On line diffusing wave spectroscopy during rheological measurements: A new instrumental setup to measure colloidal instability and structure formation in situ

2013 ◽  
Vol 54 (1) ◽  
pp. 367-372 ◽  
Author(s):  
Marcela Alexander ◽  
Milena Corredig
Author(s):  
M.A. O’Keefe ◽  
J. Taylor ◽  
D. Owen ◽  
B. Crowley ◽  
K.H. Westmacott ◽  
...  

Remote on-line electron microscopy is rapidly becoming more available as improvements continue to be developed in the software and hardware of interfaces and networks. Scanning electron microscopes have been driven remotely across both wide and local area networks. Initial implementations with transmission electron microscopes have targeted unique facilities like an advanced analytical electron microscope, a biological 3-D IVEM and a HVEM capable of in situ materials science applications. As implementations of on-line transmission electron microscopy become more widespread, it is essential that suitable standards be developed and followed. Two such standards have been proposed for a high-level protocol language for on-line access, and we have proposed a rational graphical user interface. The user interface we present here is based on experience gained with a full-function materials science application providing users of the National Center for Electron Microscopy with remote on-line access to a 1.5MeV Kratos EM-1500 in situ high-voltage transmission electron microscope via existing wide area networks. We have developed and implemented, and are continuing to refine, a set of tools, protocols, and interfaces to run the Kratos EM-1500 on-line for collaborative research. Computer tools for capturing and manipulating real-time video signals are integrated into a standardized user interface that may be used for remote access to any transmission electron microscope equipped with a suitable control computer.


2021 ◽  
Vol 109 (4) ◽  
pp. 243-260 ◽  
Author(s):  
Yves Wittwer ◽  
Robert Eichler ◽  
Dominik Herrmann ◽  
Andreas Türler

Abstract A new setup named Fast On-line Reaction Apparatus (FORA) is presented which allows for the efficient investigation and optimization of metal carbonyl complex (MCC) formation reactions under various reaction conditions. The setup contains a 252Cf-source producing short-lived Mo, Tc, Ru and Rh isotopes at a rate of a few atoms per second by its 3% spontaneous fission decay branch. Those atoms are transformed within FORA in-situ into volatile metal carbonyl complexes (MCCs) by using CO-containing carrier gases. Here, the design, operation and performance of FORA is discussed, revealing it as a suitable setup for performing single-atom chemistry studies. The influence of various gas-additives, such as CO2, CH4, H2, Ar, O2, H2O and ambient air, on the formation and transport of MCCs was investigated. O2, H2O and air were found to harm the formation and transport of MCCs in FORA, with H2O being the most severe. An exception is Tc, for which about 130 ppmv of H2O caused an increased production and transport of volatile compounds. The other gas-additives were not influencing the formation and transport efficiency of MCCs. Using an older setup called Miss Piggy based on a similar working principle as FORA, it was additionally investigated if gas-additives are mostly affecting the formation or only the transport stability of MCCs. It was found that mostly formation is impacted, as MCCs appear to be much less sensitive to reacting with gas-additives in comparison to the bare Mo, Tc, Ru and Rh atoms.


2003 ◽  
Vol 75 (9) ◽  
pp. 2166-2171 ◽  
Author(s):  
Nicolae Leopold ◽  
Michael Haberkorn ◽  
Thomas Laurell ◽  
Johan Nilsson ◽  
Josefa R. Baena ◽  
...  

1994 ◽  
Vol 347 ◽  
Author(s):  
J.Ch. Bolomey ◽  
G. Cottard ◽  
P. Berthaud ◽  
A. Lemaitre ◽  
J. F. Portala

ABSTRACTMicrowave multiport sensors have been shown to provide some unique capabilities to achieve real-time testing of products conveyed at high speed. In many applications, quantitative measurements of physical quantities such as moisture content, density, etc… are required, either to guarantee reliable production or to optimally control a fabrication/transformation process. In this paper, different ways of extracting such physical quantities from microwave measurements performed by multiport sensors are presented. Model approaches are used, based on polynomial expansions of the physical quantities to be measured as a function of the microwave amplitude and phase data. Calibration procedures have been investigated for both paper and wood material samples. Comparisons between in-situ, microwave and conventional, measurements are analysed.


2021 ◽  
Author(s):  
José R. Serrano ◽  
Luis Miguel García-Cuevas ◽  
Vishnu Samala ◽  
Juan Antonio López-Carrillo ◽  
Holger Mai

Abstract During the last decade, increasingly advanced turbocharger models have been developed for sizing, engine matching and one-dimensional modeling. This work goes further and, instead of using these models for turbocharged engines design or analysis, it implements them in the data acquisition and control system of a turbocharger gas stand. This way, interesting new capabilities arise. The paper shows that there are important synergies between advanced turbocharger gas stand data acquisition and control systems and the modern turbocharger holistic models that have not been deeply exploited until now. They can be summarized as: on-line heat fluxes analysis, in-situ outlier testing points detection, testing time saving and using digital-twin techniques to monitor turbocharger health during testing.


2018 ◽  
Vol 11 ◽  
pp. 584-590 ◽  
Author(s):  
Johanna Maier ◽  
Thomas Behnisch ◽  
Vinzenz Geske ◽  
Matthias Ahlhelm ◽  
David Werner ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document