Partial replacement of fine aggregate by steel slag and coarse aggregate by walnut shell in concrete

2020 ◽  
Author(s):  
B. Venkatesan ◽  
V.J. Lijina ◽  
V. Kannan ◽  
P.R. Dhevasenaa
Keyword(s):  
Coarse Aggregate ◽  
Steel Slag ◽  
Partial Replacement ◽  
Walnut Shell ◽  
Fine Aggregate

scholarly journals Use of Recycled Tyre Rubber in Non-structural Concrete

2018 ◽  
Vol 203 ◽  
pp. 06001
Author(s):  
Muhammad Bilal Waris ◽  
Hussain Najwani ◽  
Khalifa Al-Jabri ◽  
Abdullah Al-Saidy
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Structural Concrete ◽  
Cement Ratio ◽  
Mix Proportion ◽  
Water To Cement Ratio ◽  
Concrete Blocks

To manage tyre waste and conserve natural aggregate resource, this research investigates the use of waste tyre rubber as partial replacement of fine aggregates in non-structural concrete. The research used Taguchi method to study the influence of mix proportion, water-to-cement ratio and tyre rubber replacement percentage on concrete. Nine mixes were prepared with mix proportion of 1:2:4, 1:5:4 and 1:2.5:3; water-to-cement ratio of 0.25, 0.35 and 0.40 and rubber to fine aggregate replacement of 20%, 30% and 40%. Compressive strength and water absorption tests were carried out on 100 mm cubes. Compressive strength was directly proportional to the amount of coarse aggregate in the mix. Water-to-cement ratio increased the strength within the range used in the study. Strength was found to be more sensitive to the overall rubber content than the replacement ratio. Seven out of the nine mixes satisfied the minimum strength requirement for concrete blocks set by ASTM. Water absorption and density for all mixes satisfied the limits applicable for concrete blocks. The study indicates that mix proportions with fine to coarse aggregate ratio of less than 1.0 and w/c ratio around 0.40 can be used with tyre rubber replacements of up to 30 % to satisfy requirements for non-structural concrete.

Suitability of Quarry Dust as a Partial Replacement of Fine Aggregate in Self Compacting Concrete

2018 ◽  
Vol 877 ◽  
pp. 248-253
Author(s):  
Thete Swapnil Tanajirao ◽  
D. Arpitha ◽  
Suman Saha ◽  
C. Rajasekaran
Keyword(s):  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Self Compacting Concrete ◽  
Slump Flow ◽  
Fine Aggregates ◽  
Material Gain ◽  
Optimum Utilization ◽  
Hardened Properties ◽  
Quarry Dust

Large quantity of the quarry dust gets produced annually in the quarries during the extraction of the crushed coarse aggregate. As a result, disposal problems of this material gain significant momentum as these disturb environmental systems also. Now-a-days many of the countries like India is facing problems of ban on the extraction of sand and lacunae in procuring of fine aggregate, which is important constituent of the concrete. To overcome this problem, present study is focused on the suitability to utilize the quarry dust in Self Compacting Concrete (SCC) partially as fine aggregate with the natural fine aggregates. In this work, quarry dust is used as replacement of sand in a different level (0%, 15%, 30%, 45% and 60%) for producing the SCC. Fresh properties such as slump flow and V-funnel time have been measured for all mixes and hardened properties as compressive strength, splitting tensile strength and flexural strength of the concrete have been checked for all the mixes and it has been found that optimum utilization of quarry dust up to 30% can been done to produce SCC without compromising with its properties.

Evaluation of Steel Slag Fine Aggregate in Hot-Mix Asphalt Mixtures

1997 ◽  
Vol 1583 (1) ◽  
pp. 28-36 ◽  
Author(s):  
Prithvi S. Kandhal ◽  
Gary L. Hoffman
Keyword(s):  
Hot Mix Asphalt ◽  
Coarse Aggregate ◽  
Steel Slag ◽  
Hot Water ◽  
Test Method ◽  
Fine Aggregate ◽  
Limestone Aggregate ◽  
Aggregate Fraction ◽  
Water Conditioning ◽  
Test Criteria

Since a considerable amount of steel slag is produced in the southwestern part of Pennsylvania around Pittsburgh, where natural fine aggregate sources are limited, an evaluation was undertaken to determine the feasibility of using “cured” steel slag fine aggregate in hot-mix asphalt (HMA) mixtures. The objectives of this work were to (1) correlate fine aggregate expansions to the “parent” coarse aggregate expansions, (2) determine properties of dense-graded Pennsylvania ID-2 wearing coarse mixtures made with various sources of steel slag and crushed limestone fine aggregate, and (3) recommend appropriate specifications and test criteria for implementing the use of steel slag fine aggregate, if justifiable. Expansive characteristics of the steel slag aggregates were determined by Pennsylvania Test Method 130. HMA mixtures made with steel slag aggregates and limestone aggregate (control) were subjected to hot-water conditioning and Lottman freeze-and-thaw conditioning to determine potential problems, such as swell and moisture-induced damage. An excellent correlation existed between the average total expansion of the fine aggregate fraction and that of the “parent” coarse aggregate. No significant problems with swell and moisture-induced damage were noted in HMA mixtures containing steel slag fine aggregate and limestone coarse aggregate. Specifications and test criteria were recommended for the use of steel slag fine aggregate in HMA mixtures.

scholarly journals Behavior of Steel Slag Concrete Subjected to Elevated Temperature

2020 ◽  
Vol 9 (4) ◽  
pp. 1165-1170
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
High Temperatures ◽  
Elevated Temperatures ◽  
Coarse Aggregate ◽  
Steel Slag ◽  
Partial Replacement ◽  
High Porosity ◽  
Residual Mechanical Properties

Recycling of materials has become a major interest for engineers. At present, the amount of slag deposited in storage yard adds up to millions of tons/year leading to the occupation of farm land and serious pollution to the environment, as a result of the rapid growth in the steel industry. Steel slag is made at 1500- 1650°C having a honey comp shape with high porosity. Using steel slag as the natural aggregate with a lower waste material cost can be considered as a good alternative for sustainable constructions. The objective of this study is to evaluate the performance of residual mechanical properties of concrete with steel slag as coarse aggregate partial replacement after exposing to high temperatures .This study investigates the behavior of using granulated slag as partial or fully coarse aggregate replacement with different percentages of 0%, 15%, 30%, 50% and 100% in concrete when subjected to elevated temperatures. Six groups of concrete mixes were prepared using various replacement percentages of slag exposed to different temperatures of 400 °C, 600 °C and 800 °C for different durations of 1hr, 1.5hr and 2hr. Evaluation tests were compressive strength, tensile strength, and bond strength. The steel slag concrete mixes showed week workability lower than control mix. A systematic increasing of almost up to 21.7% in compressive strength, and 66.2% in tensile strength with increasing the percentage of steel slag replacement to 50%. And the results showed improvement on concrete residual mechanical properties after subjected to elevated temperatures with the increase of steel slag content. The findings of this study give an overview of the effect of steel slag coarse aggregate replacement on concrete after exposed to high temperatures.

scholarly journals Mechanical Behaviour on Replacement of Aggregate by E-waste in Concrete

2019 ◽  
Vol 9 (2) ◽  
pp. 302-305 ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Mechanical Behaviour ◽  
Coarse Aggregate ◽  
Environmental Problems ◽  
Waste Utilization ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Construction Work ◽  
Split Tensile Strength

Concrete is a widely used material in all construction work. The aim of the project is to study the behavior of concrete with replacement of E waste. The fine aggregate and coarse aggregate are naturally available due to increase in demand it is over exploited. The waste utilization is sustainable solution to environmental problems Waste from electric and electronic equipment is used as an E waste replacement for coarse aggregate in concrete which is used in the construction .Therefore the effects have been made to study the use of E waste components as a partial replacement of coarse aggregate in 5%, 10% and 15%. To determine the optimum percentage of E waste that can be replaced for coarse aggregate the compressive strength and split tensile strength of concrete to be studied. After determining the optimum percentage of E waste that can be replaced with coarse aggregate. The comparison of the conventional and optimum percentage of E waste replaced with concrete has been done

scholarly journals Performance of SIFCON with Steel Slag

10.29007/jxp9 ◽  
2018 ◽  
Author(s):  
Shashi Kant Sharma ◽  
Aniruddha Chopadekar ◽  
Samarth Bhatia
Keyword(s):  
Industrial Waste ◽  
High Performance ◽  
High Performance Concrete ◽  
Steel Slag ◽  
High Strength ◽  
Partial Replacement ◽  
Experimental Program ◽  
Fine Aggregate ◽  
Unique Type ◽  
The Matrix

Slurry infiltrated fibrous concrete (SIFCON) is a new and unique type of high performance concrete invented by Lankard in 1979, containing high percentage of fiber about 6% to 20% by volume. SIFCON possesses high strength as well as large ductility and has excellent potential for structural application. The matrix in SIFCON has no coarse aggregate but high cementitious content. The aim of study is to evaluate the performance of SIFCON mortar with lower fiber percentage and to minimize the fine aggregate usage by replacing it with industrial waste i.e. steel slag. Thereby, it also helps in effective disposal of industrial waste and helps in mitigating environmental pollution. The main objective of this study is to determine the effect of partial replacement of sand with steel slag on the mechanical properties of SIFCON mortar. The experimental program was carried out with 2%, 3% and 4% of fiber content by volume combined with replacement of sand by steel slag in proportion of 10% and 20% by weight. For this purpose, compressive strength, flexural strength, split tension and impact strength of SIFCON specimens were tested after 7 and 28 days of curing, yielding positive results.

scholarly journals Study of Light Weight Fibre Reinforced Concrete by Partial Replacement of Coarse Aggregate with Pumice Stone

2021 ◽  
Vol 9 (9) ◽  
pp. 933-940
Author(s):  
Mohammed Sohel Ahmed
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Light Weight ◽  
Structural Members ◽  
Conventional Concrete ◽  
Shrinkage Cracking ◽  
Pumice Stone ◽  
Average Compressive Strength

Abstract: As the demand for the structural members application in the concrete industry is continuously increasing simultaneously many a times it is required to lower the density of concrete enabling light weight which helps in easy handling of the concrete and its members. In this research an experimental endeavour has been made to equate conventional concrete with light weight by partially substituting the coarse aggregate with the pumice stone aggregate in M30 grade mix design. Simultaneously small fibres of Recron3's Polypropylene have been applied to the concrete as a reinforcing medium to minimize shrinkage cracking and improve tensile properties. The coarse aggregate was substituted by the pumice aggregate in 10, 20, 30, 40, and 50 percent and fibres respectively in 0.5, 1, 1.5, 2 and 2.5 percent. The experiment is focused on strength parameters to determine the most favourable optimum percent with respect to conventional concrete. Keywords: OPC (Ordinary Portland Cement)1, FA (Fine Aggregate)2, CA (Coarse Aggregate) 3, fck (Characteristic Compressive Strength at 28days)4, Sp. Gr (Specific Gravity)5, WC (Water Content)6, W/C (Water Cement Ratio)7, S (Standard Deviation)8, Fck (Target Average Compressive Strength at 28days)9.

scholarly journals Waste Material Ashes Used in Concrete

2019 ◽  
Vol 9 (1S3) ◽  
pp. 192-195
Keyword(s):  
Construction Industry ◽  
Coarse Aggregate ◽  
Rice Husk Ash ◽  
Waste Materials ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Fine Aggregate ◽  
Saw Dust ◽  
Sugar Cane Bagasse Ash ◽  
Disposal Problem

Disposal problem of waste materials and excessive demand on naturally available resources due to rapid urban development has opened possibilities for use of waste materials in construction industry. Many waste materials are used in concrete as replacement to cement, fine aggregate, coarse aggregate and reinforcement. Here review of some waste materials, whose ash is used as partial replacement to cement in concrete, is presented. Different properties of fresh and hardened concrete, when admixed with ash of waste materials are reviewed. Concrete containing sugar cane bagasse ash, ground nut shell ash, rice husk ash, saw dust ash, and tobacco waste ash are reviewed. After review, it is observed that further studies are required on all waste ashes replacing cement, which will reveal more potential on their usage in concrete. Concrete containing ash of waste materials attained demanded strength within 5% to 20% replacement.

Sign in / Sign up

Export Citation Format

Share Document