Investigations on structure–property relationships of activated flux TIG weldments of super-duplex/austenitic stainless steels

One of the major materials problems encountered in the development of fast breeder reactors for commercial power generation is the phenomenon of swelling in core structural components and fuel cladding. This volume expansion, which is due to the retention of lattice vacancies by agglomeration into large polyhedral clusters (voids), may amount to ten percent or greater at goal fluences in some austenitic stainless steels. From a design standpoint, this is an undesirable situation, and it is necessary to obtain experimental confirmation that such excessive volume expansion will not occur in materials selected for core applications in the Fast Flux Test Facility, the prototypic LMFBR now under construction at the Hanford Engineering Development Laboratory (HEDL). The HEDL JEM-1000 1 MeV electron microscope is being used to provide an insight into trends of radiation damage accumulation in stainless steels, since it is possible to produce atom displacements at an accelerated rate with 1 MeV electrons, while the specimen is under continuous observation.

Download Full-text

Strain-induced martensite effects on transgranular carbide precipitation in type 304 stainless steels

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100087331 ◽

1991 ◽

Vol 49 ◽

pp. 604-605

Author(s):

A.H. Advani ◽

L.E. Murr ◽

D. Matlock

Keyword(s):

Heat Treatment ◽

Grain Boundary ◽

Stress Corrosion Cracking ◽

Stainless Steels ◽

Deformation Twin ◽

Austenitic Stainless Steels ◽

Carbide Precipitation ◽

Strain Induced Martensite ◽

Type 304

Thermomechanically induced strain is a key variable producing accelerated carbide precipitation, sensitization and stress corrosion cracking in austenitic stainless steels (SS). Recent work has indicated that higher levels of strain (above 20%) also produce transgranular (TG) carbide precipitation and corrosion simultaneous with the grain boundary phenomenon in 316 SS. Transgranular precipitates were noted to form primarily on deformation twin-fault planes and their intersections in 316 SS.Briant has indicated that TG precipitation in 316 SS is significantly different from 304 SS due to the formation of strain-induced martensite on 304 SS, though an understanding of the role of martensite on the process has not been developed. This study is concerned with evaluating the effects of strain and strain-induced martensite on TG carbide precipitation in 304 SS. The study was performed on samples of a 0.051%C-304 SS deformed to 33% followed by heat treatment at 670°C for 1 h.

Download Full-text

Structure-property relationships of PE/PP sandwiched films

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100126998 ◽

1987 ◽

Vol 45 ◽

pp. 454-455

Author(s):

J. Petermann ◽

G. Broza ◽

U. Rieck ◽

A. Jaballah ◽

A. Kawaguchi

Keyword(s):

Mechanical Tests ◽

Polymer Materials ◽

Ionic Crystals ◽

Structure Property ◽

Polymer Systems ◽

Structure Property Relationships ◽

Oriented Films ◽

Materials Used ◽

Polymer Laminates ◽

Heated Glass

Oriented overgrowth of polymer materials onto ionic crystals is well known and recently it was demonstrated that this epitaxial crystallisation can also occur in polymer/polymer systems, under certain conditions. The morphologies and the resulting physical properties of such systems will be presented, especially the influence of epitaxial interfaces on the adhesion of polymer laminates and the mechanical properties of epitaxially crystallized sandwiched layers.Materials used were polyethylene, PE, Lupolen 6021 DX (HDPE) and 1810 D (LDPE) from BASF AG; polypropylene, PP, (PPN) provided by Höchst AG and polybutene-1, PB-1, Vestolen BT from Chemische Werke Hüls. Thin oriented films were prepared according to the method of Petermann and Gohil, by winding up two different polymer films from two separately heated glass-plates simultaneously with the help of a motor driven cylinder. One double layer was used for TEM investigations, while about 1000 sandwiched layers were taken for mechanical tests.

Download Full-text

Approaches for TEM imaging of cavitation in toughened nylon

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100153737 ◽

1989 ◽

Vol 47 ◽

pp. 352-353

Author(s):

Barbara A. Wood

Keyword(s):

Morphological Characteristics ◽

Structure Property ◽

Polymer Systems ◽

Selective Staining ◽

Structure Property Relationships ◽

Rubber Toughened ◽

Shear Yield ◽

Controversial Topic ◽

Selection Of ◽

Diamond Knife

A controversial topic in the study of structure-property relationships of toughened polymer systems is the internal cavitation of toughener particles resulting from damage on impact or tensile deformation.Detailed observations of the influence of morphological characteristics such as particle size distribution on deformation mechanisms such as shear yield and cavitation could provide valuable guidance for selection of processing conditions, but TEM observation of damaged zones presents some experimental difficulties.Previously published TEM images of impact fractured toughened nylon show holes but contrast between matrix and toughener is lacking; other systems investigated have clearly shown cavitated impact modifier particles. In rubber toughened nylon, the physical characteristics of cavitated material differ from undamaged material to the extent that sectioning of heavily damaged regions by cryoultramicrotomy with a diamond knife results in sections of greater than optimum thickness (Figure 1). The detailed morphology is obscured despite selective staining of the rubber phase using the ruthenium trichloride route to ruthenium tetroxide.

Download Full-text

Catalyst Halogenation Enables Rapid and Efficient Polymerizations with Visible to Near-Infrared Light

10.26434/chemrxiv.12588965 ◽

2020 ◽

Author(s):

Alex Stafford ◽

Dowon Ahn ◽

Emily Raulerson ◽

Kun-You Chung ◽

Kaihong Sun ◽

...

Keyword(s):

Near Infrared ◽

Transient Absorption ◽

Reaction Times ◽

Infrared Light ◽

Structure Property ◽

Light Emitting ◽

Structure Property Relationships ◽

Nir Light ◽

Light Intensities ◽

Emission Quenching

Driving rapid polymerizations with visible to near-infrared (NIR) light will enable nascent technologies in the emerging fields of bio- and composite-printing. However, current photopolymerization strategies are limited by long reaction times, high light intensities, and/or large catalyst loadings. Improving efficiency remains elusive without a comprehensive, mechanistic evaluation of photocatalysis to better understand how composition relates to polymerization metrics. With this objective in mind, a series of methine- and aza-bridged boron dipyrromethene (BODIPY) derivatives were synthesized and systematically characterized to elucidate key structure-property relationships that facilitate efficient photopolymerization driven by visible to NIR light. For both BODIPY scaffolds, halogenation was shown as a general method to increase polymerization rate, quantitatively characterized using a custom real-time infrared spectroscopy setup. Furthermore, a combination of steady-state emission quenching experiments, electronic structure calculations, and ultrafast transient absorption revealed that efficient intersystem crossing to the lowest excited triplet state upon halogenation was a key mechanistic step to achieving rapid photopolymerization reactions. Unprecedented polymerization rates were achieved with extremely low light intensities (< 1 mW/cm<sup>2</sup>) and catalyst loadings (< 50 μM), exemplified by reaction completion within 60 seconds of irradiation using green, red, and NIR light-emitting diodes.

Download Full-text