Study on the low-temperature annealing-induced color center in Y3+-doped PbWO4 single crystal

2009 ◽  
Vol 610 (3) ◽  
pp. 636-639
Author(s):  
Weifeng Li ◽  
Yumei Long ◽  
Xiqi Feng
Keyword(s):  
Low Temperature ◽  
Single Crystal ◽  
Color Center ◽  
Low Temperature Annealing

Anisotropic-to-Isotropic Change in Lateral Force at the Surface of Single-Crystal Lamellae of High-Density Polyethylene during Low-Temperature Annealing

2004 ◽  
Vol 37 (13) ◽  
pp. 5115-5117 ◽  
Author(s):  
Yuji Ryousho ◽  
Sono Sasaki ◽  
Toshihiko Nagamura ◽  
Atsushi Takahara ◽  
Tisato Kajiyama
Keyword(s):  
Low Temperature ◽  
Single Crystal ◽  
High Density Polyethylene ◽  
Lateral Force ◽  
High Density ◽  
Low Temperature Annealing

Low-temperature annealing of YBa2Cu3O7-x

1992 ◽  
Vol 50 (1) ◽  
pp. 88-89
Author(s):  
R.L. Sabatini ◽  
Yimei Zhu ◽  
Masaki Suenaga ◽  
A.R. Moodenbaugh
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Low Temperature ◽  
Oxygen Diffusion ◽  
Diffusion Rate ◽  
Oxygen Depletion ◽  
Low Temperature Annealing ◽  
Transmission Electron ◽  
Microstructural Effects ◽  
Oxygen Diffusion Rate

Low temperature annealing (<400°C) of YBa2Cu3O7x in a ozone containing oxygen atmosphere is sometimes carried out to oxygenate oxygen deficient thin films. Also, this technique can be used to fully oxygenate thinned TEM specimens when oxygen depletion in thin regions is suspected. However, the effects on the microstructure nor the extent of oxygenation of specimens has not been documented for specimens exposed to an ozone atmosphere. A particular concern is the fact that the ozone gas is so reactive and the oxygen diffusion rate at these temperatures is so slow that it may damage the specimen by an over-reaction. Thus we report here the results of an investigation on the microstructural effects of exposing a thinned YBa2Cu3O7-x specimen in an ozone atmosphere using transmission electron microscopy and energy loss spectroscopy techniques.

ФОРМИРОВАНИЕ ПЕРЕХОДНОГО СЛОЯ ALN НА ТЕМПЛЕЙТАХ 3С-SIC/SI(111) МЕТОДОМ АММИАЧНОЙ МОЛЕКУЛЯРНО-ЛУЧЕВОЙ ЭПИТАКСИИ

2020 ◽  
Vol 96 (3s) ◽  
pp. 148-153
Author(s):  
С.Д. Федотов ◽  
А.В. Бабаев ◽  
В.Н. Стаценко ◽  
К.А. Царик ◽  
В.К. Неволин
Keyword(s):  
Crystal Structure ◽  
Growth Rate ◽  
Low Temperature ◽  
Surface Morphology ◽  
Single Crystal ◽  
Root Mean Square Roughness ◽  
Rate Variation ◽  
Mean Square ◽  
Nucleation Layer ◽  
Low Temperature Epitaxy

Представлены результаты изучения морфологии поверхности и структуры слоев AlN, сформированных аммиачной МЛЭ на темплейтах 3C-SiC/Si(111) on-axis- и 4° off-axis-разориентации. Опробован технологический режим низкотемпературной эпитаксии зародышевого слоя AlN на поверхности 3C-SiC(111). Среднеквадратичная шероховатость поверхности (5 х 5 мкм) слоев AlN толщиной 150 ± 50 нм составила 2,5-3,5 нм на темплейтах 3C-SiC/Si(111) on-axis и 3,3-3,5 нм на 4° off-axis. Показано уменьшение шероховатости смачивающего слоя AlN при изменении скорости роста. Получены монокристаллические слои AlN(0002) со значениями FWHM (ω-геометрия) 1,4-1,6°. The paper presents the surface morphology and crystal structure of AlN layers formed by ammonia MBE on 3C-SiC/Si(111) on-axis and 4° off-axis disorientation. It offers the technological approach of low-temperature epitaxy of the AlN nucleation layer on the 3C-SiC (111) surface. Root mean square roughness (5 х 5 |xm) of AlN layers with thickness of 150 ± 50 nm was 2,5-3,5 nm onto on-axis templates and 3.3-3.5 nm onto 4° off-axis. It appears that the RMS roughness of the AlN surface is changing with the growth rate variation. Single-crystal AlN(0002) layers with FWHM values (ω-geometry) of 1.4-1.6° have been obtained.

scholarly journals Effects of equal channel angular pressing and heat treatments on the microstructures and mechanical properties of selective laser melted and cast AlSi10Mg alloys

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Przemysław Snopiński ◽  
Mariusz Król ◽  
Marek Pagáč ◽  
Jana Petrů ◽  
Jiří Hajnyš ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Heat Treatments ◽  
Electron Backscattered Diffraction ◽  
Angular Pressing ◽  
Low Temperature Annealing ◽  
Transmission Electron ◽  
Before And After ◽  
The Impact

AbstractThis study investigated the impact of the equal channel angular pressing (ECAP) combined with heat treatments on the microstructure and mechanical properties of AlSi10Mg alloys fabricated via selective laser melting (SLM) and gravity casting. Special attention was directed towards determining the effect of post-fabrication heat treatments on the microstructural evolution of AlSi10Mg alloy fabricated using two different routes. Three initial alloy conditions were considered prior to ECAP deformation: (1) as-cast in solution treated (T4) condition, (2) SLM in T4 condition, (3) SLM subjected to low-temperature annealing. Light microscopy, transmission electron microscopy, X-ray diffraction line broadening analysis, and electron backscattered diffraction analysis were used to characterize the microstructures before and after ECAP. The results indicated that SLM followed by low-temperature annealing led to superior mechanical properties, relative to the two other conditions. Microscopic analyses revealed that the partial-cellular structure contributed to strong work hardening. This behavior enhanced the material’s strength because of the enhanced accumulation of geometrically necessary dislocations during ECAP deformation.

Low temperature acoustic characterization of PMN single crystal

2017 ◽  
Vol 122 (8) ◽  
pp. 084103 ◽  
Author(s):  
E. Smirnova ◽  
A. Sotnikov ◽  
S. Ktitorov ◽  
H. Schmidt
Keyword(s):  
Low Temperature ◽  
Single Crystal ◽  
Acoustic Characterization
Sign in / Sign up

Export Citation Format

Share Document