Deformation behavior in bulk nanocrystalline-ultrafine aluminum: in situ evidence of plastic strain recovery

2009 ◽  
Vol 60 (7) ◽  
pp. 520-523 ◽  
Author(s):  
I LONARDELLI ◽  
J ALMER ◽  
G ISCHIA ◽  
C MENAPACE ◽  
A MOLINARI
Keyword(s):  
Plastic Strain ◽  
Deformation Behavior ◽  
Strain Recovery ◽  
Ultrafine Aluminum ◽  
Bulk Nanocrystalline

In Situ Study on the Compression Deformation Behavior of MoNbTaVW High-Entropy Alloy

2020 ◽  
Author(s):  
Congyan Zhang ◽  
Binbin Yue ◽  
Uttam Bhandari ◽  
Oleg Starovoytov ◽  
Yan Yang ◽  
...  
Keyword(s):  
Deformation Behavior ◽  
High Entropy Alloy ◽  
High Entropy ◽  
Compression Deformation

scholarly journals Study on Microstructure and In Situ Tensile Deformation Behavior of Fe-25Mn-xAl-8Ni-C Alloy Prepared by Vacuum Arc Melting

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 814
Author(s):  
Yaping Bai ◽  
Meng Li ◽  
Chao Cheng ◽  
Jianping Li ◽  
Yongchun Guo ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Austenite Phase ◽  
Vacuum Arc ◽  
Al Content ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Tensile Deformation Behavior

In this study, Fe-25Mn-xAl-8Ni-C alloys (x = 10 wt.%, 11 wt.%, 12 wt.%, 13 wt.%) were prepared by a vacuum arc melting method, and the microstructure of this series of alloys and the in situ tensile deformation behavior were studied. The results showed that Fe-25Mn-xAl-8Ni-C alloys mainly contained austenite phase with a small amount of NiAl compound. With the content of Al increasing, the amount of austenite decreased while the amount of NiAl compound increased. When the Al content increased to 12 wt.%, the interface between austenite and NiAl compound and austenitic internal started to precipitate k-carbide phase. In situ tensile results also showed that as the content of Al increased, the alloy elongation decreased gradually, and the tensile strength first increased and then decreased. When the Al content was up to 11 wt.%, the elongation and tensile strength were 2.6% and 702.5 MPa, respectively; the results of in situ tensile dynamic observations show that during the process of stretching, austenite deformed first, and crack initiation mainly occurred at the interface between austenite and NiAl compound, and propagated along the interface, resulting in fracture of the alloy.

Mechanical Properties of Nanocrystalline Materials Produced by In Situ Consolidation Ball Milling

2008 ◽  
Vol 579 ◽  
pp. 15-28 ◽  
Author(s):  
Carl C. Koch ◽  
Khaled M. Youssef ◽  
Ron O. Scattergood
Keyword(s):  
Mechanical Properties ◽  
Ball Milling ◽  
Nanocrystalline Materials ◽  
Preparation Method ◽  
High Strength ◽  
Al Alloys ◽  
Ductile Metals ◽  
Cu Alloys ◽  
Bulk Nanocrystalline

This paper reviews a method, “in situ consolidation ball milling” that provides artifactfree bulk nanocrystalline samples for several ductile metals such as Zn, Al and Al alloys, and Cu and Cu alloys. The preparation method is described in this paper and examples of the mechanical behavior of nanocrystalline materials made by this technique are given. It is found that in such artifact-free metals, combinations of both high strength and good ductility are possible.

Judgement Method for Surrounding Rock Stability of Guanjiao Tunnel Based on Catastrophe Theory

2011 ◽  
Vol 90-93 ◽  
pp. 2307-2312 ◽  
Author(s):  
Wen Jiang Li ◽  
Su Min Zhang ◽  
Xian Min Han
Keyword(s):  
Plastic Strain ◽  
Catastrophe Theory ◽  
Soft Rock ◽  
Surrounding Rock ◽  
In Situ Monitoring ◽  
Engineering Practice ◽  
Stability Of Surrounding Rock ◽  
The Stability ◽  
Rock Tunnel

The stability judgement of surrounding rock is one of the key jobs in tunnel engineering. Taking the Erlongdong fault bundle section of Guanjiao Tunnel as the background, the stability of surrounding rock during construction of soft rock tunnel was discussed preliminarily. Based on plastic strain catastrophe theory, and combining numerical results and in-situ data, the limit displacements for stability of surrounding rock were analyzed and obtained corresponding to the in-situ monitoring technology. It shows that the limit displacements obtained corresponds to engineering practice primarily. The plastic strain catastrophe theory under unloading condition provides new thought for ground stability of deep soft rock tunnel and can be good guidance and valuable reference to construction decision making and deformation managing of similar tunnels.

Nanoclay-reinforced Polyacrylamide Composite: Synthesis, Structural and Mechanical Characterization

2009 ◽  
Vol 1239 ◽  
Author(s):  
Yong Sun ◽  
Zaiwang Huang ◽  
Xiaodong Li
Keyword(s):  
Thin Films ◽  
Deformation Behavior ◽  
Mechanical Characterization ◽  
Interfacial Strength ◽  
Localized Deformation ◽  
Nano Indentation ◽  
Atomic Force ◽  
Nanocomposite Thin Films ◽  
Synthesized Materials

AbstractA facile electrophoretic deposition method was successfully applied to achieve novel nanoclay-reinforced polyacrylamide nanocomposite thin films. A special curled architecture of the re-aggregated nanoclay-platelets was identified, providing a possible source for realizing the interlocking mechanism in the nanocomposites. The curled architecture could be the result from strain releasing when the thin films were peeled off from the substrates. Through micro-/nano-indentation and in situ observation of the deformation during tensile test with an atomic force microscope (AFM), the localized deformation mechanism of the synthesized materials was investigated in further details. The results implied that a localized crack diversion mechanism worked in the synthesized nanocomposite thin films, which resembled its nature counterpart-nacre. The deformation behavior and fracture mechanism were discussed with reference to lamellar structure, interfacial strength between the nanoclays and the polyacrylamide matrix, and nanoclay agglomeration.

Sign in / Sign up

Export Citation Format

Share Document