Wear analysis of materials used as orthopaedic implants

The paper presents and experimental study upon several types of materials used for dental works (especially prosthetic works) after prolonged use (over 10 years). The issues that lead to the necessity of changing the prosthetic works are the results of multiple types of wear. Our aim is to determine the extension of damage by digital microscopy, probable causes and analyze the benefits and disadvantages of the most used materials in prosthetic works.

Download Full-text

Wear Analysis of Materials Used for a Track Steering System in Abrasive Soil Mass

Materials ◽

10.3390/ma14206164 ◽

2021 ◽

Vol 14 (20) ◽

pp. 6164

Author(s):

Klaudia Olejniczak ◽

Jerzy Napiórkowski

Keyword(s):

High Density Polyethylene ◽

Comparative Research ◽

Resistance Index ◽

Soil Mass ◽

Steering System ◽

Hadfield Steel ◽

Natural Soil ◽

Wear Analysis ◽

Ethylene Content ◽

Materials Used

This paper presents the results of comparative research on materials used for a track steering system in an abrasive soil mass. Two types of elastomer tracks were tested: a steel-rubber stave from an asphalt paver and a rubber overlay used in vehicles with a steel track chain. The results obtained were related to the wear of Hadfield steel. The tests were carried out on a “spinning bowl” stand in a natural soil mass, which consisted of two types of soil: light and heavy. It was shown that the resistance to abrasive wear depended on the grain size of the worked soil and the chemical composition of the materials. Rubber overlay was found to have the highest resistance index in all types of soils. It was made of high-density polyethylene, low-density polyethylene, ethylene acrylate/ethyl copolymer (ethylene acrylate 18%) and ethylene/propylene copolymer with an ethylene content of 60%. An analysis of the condition of the machined surfaces after friction tests complements the results presented.

Download Full-text

Deformation Replication

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100068394 ◽

1970 ◽

Vol 28 ◽

pp. 280-281

Author(s):

J. Temple Black

Keyword(s):

Cutting Speed ◽

Machining Process ◽

Depth Of Cut ◽

Rake Face ◽

Orthogonal Machining ◽

Aluminum Chips ◽

Before And After ◽

Materials Used ◽

Glass Knife ◽

Very High

Tool materials used in ultramicrotomy are glass, developed by Latta and Hartmann (1) and diamond, introduced by Fernandez-Moran (2). While diamonds produce more good sections per knife edge than glass, they are expensive; require careful mounting and handling; and are time consuming to clean before and after usage, purchase from vendors (3-6 months waiting time), and regrind. Glass offers an easily accessible, inexpensive material ($0.04 per knife) with very high compressive strength (3) that can be employed in microtomy of metals (4) as well as biological materials. When the orthogonal machining process is being studied, glass offers additional advantages. Sections of metal or plastic can be dried down on the rake face, coated with Au-Pd, and examined directly in the SEM with no additional handling (5). Figure 1 shows aluminum chips microtomed with a 75° glass knife at a cutting speed of 1 mm/sec with a depth of cut of 1000 Å lying on the rake face of the knife.

Download Full-text

High Voltage Transmission Microscopy of Surveyor III Camera Shrouds

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100064748 ◽

1971 ◽

Vol 29 ◽

pp. 138-139

Author(s):

W. R. Duff ◽

L. E. Thomas ◽

R. M. Fisher ◽

S. V. Radcliffe

Keyword(s):

Alloy Sheet ◽

Transmission Microscopy ◽

Television Camera ◽

Window Method ◽

Transmission Electron ◽

Microstructural Effects ◽

Lunar Environment ◽

Successful Retrieval ◽

Materials Used ◽

Abrasive Paper

Successful retrieval of the television camera and other components from the Surveyor III spacecraft by the Apollo 12 astronauts has provided a unique opportunity to study the effects of a known and relatively extensive exposure to the lunar environment. Microstructural effects including those produced by micro-meteorite impact, radiation damage (by both the solar wind and cosmic rays) and solar heating might be expected in the materials used to fabricate the spacecraft. Samples received were in the form of 1 cm2 of painted unpainted aluminum alloy sheet from the top of the camera visor (JPL Code 933) and the sides (935,936) and bottom (934) of the lower camera shroud. They were prepared for transmission electron microscopy by first hand-grinding with abrasive paper to a thickness of 0.006". The edges were lacquered and the sample electropolished in 10% perchloric methanol using the “window” method, to a thickness of ~0.001". Final thinning was accomplished by polishing 3 mm punched disks in an acetic-phosphoric-nitric acid solution.

Download Full-text

Structure-property relationships of PE/PP sandwiched films

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100126998 ◽

1987 ◽

Vol 45 ◽

pp. 454-455

Author(s):

J. Petermann ◽

G. Broza ◽

U. Rieck ◽

A. Jaballah ◽

A. Kawaguchi

Keyword(s):

Mechanical Tests ◽

Polymer Materials ◽

Ionic Crystals ◽

Structure Property ◽

Polymer Systems ◽

Structure Property Relationships ◽

Oriented Films ◽

Materials Used ◽

Polymer Laminates ◽

Heated Glass

Oriented overgrowth of polymer materials onto ionic crystals is well known and recently it was demonstrated that this epitaxial crystallisation can also occur in polymer/polymer systems, under certain conditions. The morphologies and the resulting physical properties of such systems will be presented, especially the influence of epitaxial interfaces on the adhesion of polymer laminates and the mechanical properties of epitaxially crystallized sandwiched layers.Materials used were polyethylene, PE, Lupolen 6021 DX (HDPE) and 1810 D (LDPE) from BASF AG; polypropylene, PP, (PPN) provided by Höchst AG and polybutene-1, PB-1, Vestolen BT from Chemische Werke Hüls. Thin oriented films were prepared according to the method of Petermann and Gohil, by winding up two different polymer films from two separately heated glass-plates simultaneously with the help of a motor driven cylinder. One double layer was used for TEM investigations, while about 1000 sandwiched layers were taken for mechanical tests.

Download Full-text