Scientific Bases for Selection of Bifocal Lenses

1936 ◽  
Vol 19 (8) ◽  
pp. 675-683
Author(s):  
Albert L. Anderson
Keyword(s):  
2021 ◽  
Author(s):  
Aditya Tripathi

Aim: To reveal the patients point of view about the selection of different presbyopic correction options from ophthalmic lenses and awareness about presbyopia. Methodology: In this Prospective study, feedback questionnaire based study in North India, 126 subjects were enrolled and the offline questionnaire and responses were recorded. Participants’ age ranged between 37 -75 years (using near correction). Evaluated the responses to know the reasons of chosen of different options for pre-presbyopia and presbyopia correction by the subjects and attitudes about it, its importance, and present conventional correction opinions including bifocals, progressive addition lenses and contact lenses. Result: Among the all participants, number of participants between the age group 37- 45 (pre-presbyopes) were 35 (27.77%), between 45-55 years of aged group were 60 (47.61%) participants and rest of 31 (24.60%) participants were between 55-75 years of aged group. Forty eight participants (38.1%) were already wearing a near correction while seventy eight (61.9%) were not wear any near correction. Out of 126, the 6 (4.76%) subjects were chosen a near visual correction and separated glasses, 88 (69.84%) subjects were chosen the bifocal lenses, rest of all 32 (25.89%) subjects chosen the PALs. And no one was using contact lens for near correction. Few similarities were observed as age–related (75.38%), total unaware of word presbyopia (85.71%), comfort, convenience and appearance concerned (63%). Conclusion: The spectacles were most preferred for the correction of presbyopia. Bifocals are taken by majority of population. After educating about Presbyopia and advantages of PALs, it was revealed that most of the subjects wanted to choose PALs because of comfort and convenience to see all distances but most of them denied due to cost and 4-8 days adaptation time. So most of the subjects were chosen the bifocal lenses even they knew the disadvantages of it like image jump and segment line, while comfort, convenience and cosmetic appearance were seen as the preferred than cost. But cost also played role while finalize the lens and its coatings types.


2019 ◽  
Vol 42 ◽  
Author(s):  
Gian Domenico Iannetti ◽  
Giorgio Vallortigara

Abstract Some of the foundations of Heyes’ radical reasoning seem to be based on a fractional selection of available evidence. Using an ethological perspective, we argue against Heyes’ rapid dismissal of innate cognitive instincts. Heyes’ use of fMRI studies of literacy to claim that culture assembles pieces of mental technology seems an example of incorrect reverse inferences and overlap theories pervasive in cognitive neuroscience.


1975 ◽  
Vol 26 ◽  
pp. 395-407
Author(s):  
S. Henriksen

The first question to be answered, in seeking coordinate systems for geodynamics, is: what is geodynamics? The answer is, of course, that geodynamics is that part of geophysics which is concerned with movements of the Earth, as opposed to geostatics which is the physics of the stationary Earth. But as far as we know, there is no stationary Earth – epur sic monere. So geodynamics is actually coextensive with geophysics, and coordinate systems suitable for the one should be suitable for the other. At the present time, there are not many coordinate systems, if any, that can be identified with a static Earth. Certainly the only coordinate of aeronomic (atmospheric) interest is the height, and this is usually either as geodynamic height or as pressure. In oceanology, the most important coordinate is depth, and this, like heights in the atmosphere, is expressed as metric depth from mean sea level, as geodynamic depth, or as pressure. Only for the earth do we find “static” systems in use, ana even here there is real question as to whether the systems are dynamic or static. So it would seem that our answer to the question, of what kind, of coordinate systems are we seeking, must be that we are looking for the same systems as are used in geophysics, and these systems are dynamic in nature already – that is, their definition involvestime.


1978 ◽  
Vol 48 ◽  
pp. 515-521
Author(s):  
W. Nicholson

SummaryA routine has been developed for the processing of the 5820 plates of the survey. The plates are measured on the automatic measuring machine, GALAXY, and the measures are subsequently processed by computer, to edit and then refer them to the SAO catalogue. A start has been made on measuring the plates, but the final selection of stars to be made is still a matter for discussion.


Author(s):  
P.J. Killingworth ◽  
M. Warren

Ultimate resolution in the scanning electron microscope is determined not only by the diameter of the incident electron beam, but by interaction of that beam with the specimen material. Generally, while minimum beam diameter diminishes with increasing voltage, due to the reduced effect of aberration component and magnetic interference, the excited volume within the sample increases with electron energy. Thus, for any given material and imaging signal, there is an optimum volt age to achieve best resolution.In the case of organic materials, which are in general of low density and electric ally non-conducting; and may in addition be susceptible to radiation and heat damage, the selection of correct operating parameters is extremely critical and is achiev ed by interative adjustment.


Author(s):  
P. M. Lowrie ◽  
W. S. Tyler

The importance of examining stained 1 to 2μ plastic sections by light microscopy has long been recognized, both for increased definition of many histologic features and for selection of specimen samples to be used in ultrastructural studies. Selection of specimens with specific orien ation relative to anatomical structures becomes of critical importance in ultrastructural investigations of organs such as the lung. The uantity of blocks necessary to locate special areas of interest by random sampling is large, however, and the method is lacking in precision. Several methods have been described for selection of specific areas for electron microscopy using light microscopic evaluation of paraffin, epoxy-infiltrated, or epoxy-embedded large blocks from which thick sections were cut. Selected areas from these thick sections were subsequently removed and re-embedded or attached to blank precasted blocks and resectioned for transmission electron microscopy (TEM).


Author(s):  
K.-H. Herrmann ◽  
D. Krahl ◽  
H.-P Rust

The high detection quantum efficiency (DQE) is the main requirement for an imagerecording system used in electron microscopy of radiation-sensitive specimens. An electronic TV system of the type shown in Fig. 1 fulfills these conditions and can be used for either analog or digital image storage and processing [1], Several sources of noise may reduce the DQE, and therefore a careful selection of various elements is imperative.The noise of target and of video amplifier can be neglected when the converter stages produce sufficient target electrons per incident primary electron. The required gain depends on the type of the tube and also on the type of the signal processing chosen. For EBS tubes, for example, it exceeds 10. The ideal case, in which all impinging electrons create uniform charge peaks at the target, is not obtainable for several reasons, and these will be discussed as they relate to a system with a scintillator, fiber-optic and photo-cathode combination as the first stage.


Author(s):  
L.E. Murr ◽  
A.B. Draper

The industrial characterization of the machinability of metals and alloys has always been a very arbitrarily defined property, subject to the selection of various reference or test materials; and the adoption of rather naive and misleading interpretations and standards. However, it seems reasonable to assume that with the present state of knowledge of materials properties, and the current theories of solid state physics, more basic guidelines for machinability characterization might be established on the basis of the residual machined microstructures. This approach was originally pursued by Draper; and our presentation here will simply reflect an exposition and extension of this research.The technique consists initially in the production of machined chips of a desired test material on a horizontal milling machine with the workpiece (specimen) mounted on a rotary table vice. A single cut of a specified depth is taken from the workpiece (0.25 in. wide) each at a new tool location.


Author(s):  
J. F. Hainfeld ◽  
J. S. Wall

Cost reduction and availability of specialized hardware for image processing have made it reasonable to purchase a stand-alone interactive work station for computer aided analysis of micrographs. Some features of such a system are: 1) Ease of selection of points of interest on the micrograph. A cursor can be quickly positioned and coordinates entered with a switch. 2) The image can be nondestructively zoomed to a higher magnification for closer examination and roaming (panning) can be done around the picture. 3) Contrast and brightness of the picture can be varied over a very large range by changing the display look-up tables. 4) Marking items of interest can be done by drawing circles, vectors or alphanumerics on an additional memory plane so that the picture data remains intact. 5) Color pictures can easily be produced. Since the human eye can detect many more colors than gray levels, often a color encoded micrograph reveals many features not readily apparent with a black and white display. Colors can be used to construct contour maps of objects of interest. 6) Publication quality prints can easily be produced by taking pictures with a standard camera of the T.V. monitor screen.


Sign in / Sign up

Export Citation Format

Share Document