An experimental study of the relationship between surface roughness and stress in EHL contacts

2000 ◽  
pp. 735-746 ◽  
Author(s):  
C.J. Hooke ◽  
K.Y. Li
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
The Relationship

scholarly journals Investigate the Effect of Cutting Parameters on Surface Roughness When Milling X12m Steel

2021 ◽  
pp. 258-263
Author(s):  
Do Thi Kim Lien ◽  
Nguyen Dinh Man ◽  
Phung Tran Dinh
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Face Milling ◽  
Negligible Effect ◽  
Depth Of Cut ◽  
The Relationship

In this paper, an experimental study on the effect of cutting parameters on surface roughness was conducted when milling X12M steel. The cutting tool used in this study is a face milling cutter. The material that is used to make the insert is the hard alloy T15K6. The cutting parameters covered in this study include the cutting speed, the feed rate and depth of cut. The experiments are performed in the form of a rotating center composite design. The analysis shows that for both Ra and Rz: (1) the feed rate has the greatest influence on the surface roughness while the depth of cut, the cutting speed has a negligible effect on the surface roughness. (2) only the interaction between the feed rate and the depth of the cut has a significant effect on both Ra and Rz while the interaction between the cutting speed and the feed rate, the interaction between the cutting speed and the depth of cut have a negligible effect on surface roughness. A regression equation showing the relationship between Ra, Rz, and cutting parameters has also been built in this study.

scholarly journals Experimental Study on Ultrasonic Shot Peening Forming and Surface Properties of AALY12

2015 ◽  
Vol 1094 ◽  
pp. 339-342
Author(s):  
Chao Xun Liu ◽  
Shi Hong Lu ◽  
Wei Miao ◽  
Pan Feng Song ◽  
Tian Rui Wu
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Electric Current ◽  
Shot Peening ◽  
Processing Time ◽  
Radius Of Curvature ◽  
Micro Hardness ◽  
Current Time ◽  
Ultrasonic Shot Peening ◽  
The Relationship

Ultrasonic shot peening (USP) on AALY12 sheet was studied. Several parameters (arc heights, surface roughness, surface topography and micro hardness) with different USP process parameters were measured. The research proposes that radius of curvature of shot peened sheet increases with time and electric current decreasing, while increases with pin diameter increasing, and radius of curvature reaches a saturation level after a specific processing time and electric current. An empirical model of the relationship between radius of curvature and pin diameter, electric current, time was also obtained. The research shows that the increment of surface and vertical micro hardness of material is more obvious with longer time and higher value of electric current, which can be up to 20% and 28% respectively.

scholarly journals What Makes a Floor Slippery? A Brief Experimental Study of Ceramic Tiles Slip Resistance Depending on Their Properties and Surface Conditions

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7064
Author(s):  
Ewa Sudoł ◽  
Marcin Małek ◽  
Mateusz Jackowski ◽  
Marcin Czarnecki ◽  
Cezary Strąk
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Experimental Measurements ◽  
Ceramic Tiles ◽  
Main Determinant ◽  
Surface Conditions ◽  
Slip Resistance ◽  
Dry Conditions ◽  
Value Of It ◽  
The Relationship

The safety of the use of construction facilities should be a priority in today’s busy world, where it is not difficult to get involved in an accident. Most of them, due to the pace at which we live today, are caused by slips, trips, and falls. This work presents a detailed analysis of the resistance of ceramic floors to these events, taking into account the surface properties and conditions (dry/wet), which, as presented, have a significant impact on the final slip resistance values. This study also investigates the relationship between surface roughness and anti-slip properties. According to the obtained results, it can be concluded that the surface roughness is not the main determinant of slip resistance, and the final value of it is influenced by many components that should be considered together and not be neglected when designing the surface finish. Furthermore, based on experimental measurements, it can be noted that the highest slip resistance in both wet and dry conditions showed the unglazed tiles with lapatto finish and the glazed tiles without any extra finish.

Possible examinations of stone machining focused on the relationship between technological parameters and surface quality

2013 ◽  
Vol 4 (1) ◽  
pp. 63-68 ◽  
Author(s):  
Zs. Kun ◽  
I. G. Gyurika
Keyword(s):  
Surface Roughness ◽  
Metal Cutting ◽  
Cutting Speed ◽  
Theoretical Background ◽  
Motion Path ◽  
Depth Of Cut ◽  
Manufacturing Cost ◽  
Technological Parameters ◽  
The Relationship ◽  
Manufacturing Time

Abstract The stone products with different sizes, geometries and materials — like machine tool's bench, measuring machine's board or sculptures, floor tiles — can be produced automatically while the manufacturing engineer uses objective function similar to metal cutting. This function can minimise the manufacturing time or the manufacturing cost, in other cases it can maximise of the tool's life. To use several functions, manufacturing engineers need an overall theoretical background knowledge, which can give useful information about the choosing of technological parameters (e.g. feed rate, depth of cut, or cutting speed), the choosing of applicable tools or especially the choosing of the optimum motion path. A similarly important customer's requirement is the appropriate surface roughness of the machined (cut, sawn or milled) stone product. This paper's first part is about a five-month-long literature review, which summarizes in short the studies (researches and results) considered the most important by the authors. These works are about the investigation of the surface roughness of stone products in stone machining. In the second part of this paper the authors try to determine research possibilities and trends, which can help to specify the relation between the surface roughness and technological parameters. Most of the suggestions of this paper are about stone milling, which is the least investigated machining method in the world.

Quantity judgment and the mass-count distinction across languages: Advances, problems, and future directions for research

2018 ◽  
Author(s):  
David Barner ◽  
Alan Bale
Keyword(s):  
Experimental Study ◽  
Judgment Task ◽  
Scientific Enterprise ◽  
Future Directions ◽  
Quantity Judgment ◽  
The Relationship ◽  
Linguistic Cognition

We review advances in the experimental study of the mass-count distinction and highlight problems that have emerged. First, we lay out what we see to be the scientific enterprise of studying the syntax and semantics of mass-count distinction, and the assumptions we believe must be made if additional progress is to occur, especially as the empirical facts continue to grow in number and complexity. Second, we discuss the new landscape of cross-linguistic results that has been created by widespread use of the quantity judgment task, and what these results tell us about the nature of the mass-count distinction. Finally, we discuss the relationship between the mass-count distinction and non-linguistic cognition, and in particular the object-substance distinction.

External Investigators' Follow-Up Intentions When Whistleblowers Report Healthcare Fraud: The Effects of Report Anonymity and Previous Confrontation

2020 ◽  
Vol 32 (2) ◽  
pp. 91-101
Author(s):  
Steven E. Kaplan ◽  
Danny Lanier ◽  
Kelly R. Pope ◽  
Janet A. Samuels
Keyword(s):  
Experimental Study ◽  
Early Detection ◽  
Data Availability ◽  
Medical Provider ◽  
Perceived Credibility ◽  
The Relationship ◽  
Critical Investigation

ABSTRACT Whistleblowing reports, if properly investigated, facilitate the early detection of fraud. Although critical, investigation-related decisions represent a relatively underexplored component of the whistleblowing process. Investigators are responsible for initially deciding whether to follow-up on reports alleging fraud. We report the results of an experimental study examining the follow-up intentions of highly experienced healthcare investigators. Participants, in the role of an insurance investigator, are asked to review a whistleblowing report alleging billing fraud occurring at a medical provider. Thus, participants are serving as external investigators. In a between-participant design, we manipulate the report type and whether the caller previously confronted the wrongdoer. We find that compared to an anonymous report, a non-anonymous report is perceived as more credible and follow-up intentions stronger. We also find that perceived credibility fully mediates the relationship between report type and follow-up intentions. Previous confrontation is not significantly associated with either perceived credibility or follow-up intentions. Data Availability: Data are available upon request.

Sign in / Sign up

Export Citation Format

Share Document