Charging/discharge events in coated spacecraft polymers during electron beam irradiation in a scanning electron microscope

This paper reported a method of multiwalled carbon nanotubes (MWCNTs) fusion inside a scanning electron microscope (SEM). A CNT was picked up by nanorobotics manipulator system which was constructed in SEM with 21 DOFs and 1 nm resolution. The CNT was picked up and placed on two manipulators. The tensile force was 140 nN when the CNT was pulled into two parts. Then, two parts of the CNT were connected to each other by two manipulators. The adhered force between two parts was measured to be about 20 nN. When the two parts of CNT were connected again, the contact area was fused by focused electron beam irradiation for 3 minutes. The tensile force of the junction was measured to be about 100 nN. However, after fusion, the tensile force was five times larger than the tensile force connected only by van der Waals force. This force was 70 percent of the tensile force before pulling out of CNTs. The results revealed that the electron beam irradiation was a promising method for CNT fusion. We hope this technology will be applied to nanoelectronics in the near future.

Download Full-text

X-ray micro tomography in the scanning electron microscope

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100107678 ◽

1978 ◽

Vol 36 (1) ◽

pp. 106-107 ◽

Cited By ~ 1

Author(s):

W. Brünger

Keyword(s):

Electron Beam ◽

Electron Microscope ◽

Scanning Electron Microscope ◽

Target Surface ◽

The Body ◽

X Rays ◽

Cross Sectional ◽

X Ray ◽

Micro Tomography ◽

Scanning Electron

Reconstructive tomography is a new technique in diagnostic radiology for imaging cross-sectional planes of the human body /1/. A collimated beam of X-rays is scanned through a thin slice of the body and the transmitted intensity is recorded by a detector giving a linear shadow graph or projection (see fig. 1). Many of these projections at different angles are used to reconstruct the body-layer, usually with the aid of a computer. The picture element size of present tomographic scanners is approximately 1.1 mm2.Micro tomography can be realized using the very fine X-ray source generated by the focused electron beam of a scanning electron microscope (see fig. 2). The translation of the X-ray source is done by a line scan of the electron beam on a polished target surface /2/. Projections at different angles are produced by rotating the object.During the registration of a single scan the electron beam is deflected in one direction only, while both deflections are operating in the display tube.

Download Full-text

High Resolution Scanning Electron Microscopy

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100086696 ◽

1991 ◽

Vol 49 ◽

pp. 478-479

Author(s):

David Joy ◽

James Pawley

Keyword(s):

Electron Microscopy ◽

Scanning Electron Microscopy ◽

Electron Beam ◽

Electron Microscope ◽

High Resolution ◽

Scanning Electron Microscope ◽

Electron Probe ◽

Impact Point ◽

Interaction Volume ◽

Scanning Electron

The scanning electron microscope (SEM) builds up an image by sampling contiguous sub-volumes near the surface of the specimen. A fine electron beam selectively excites each sub-volume and then the intensity of some resulting signal is measured. The spatial resolution of images made using such a process is limited by at least three factors. Two of these determine the size of the interaction volume: the size of the electron probe and the extent to which detectable signal is excited from locations remote from the beam impact point. A third limitation emerges from the fact that the probing beam is composed of a finite number of discrete particles and therefore that the accuracy with which any detectable signal can be measured is limited by Poisson statistics applied to this number (or to the number of events actually detected if this is smaller).

Download Full-text

Slow-Scan CCD Observation of Backscattering Patterns in SEM

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100131176 ◽

1992 ◽

Vol 50 (2) ◽

pp. 1308-1309

Author(s):

F. Ouyang ◽

D. A. Ray ◽

O. L. Krivanek

Keyword(s):

Electron Beam ◽

Electron Microscope ◽

Scanning Electron Microscope ◽

Dynamic Range ◽

High Sensitivity ◽

Lens System ◽

Wide Dynamic Range ◽

Peltier Cooler ◽

Diffraction Patterns ◽

Scanning Electron

Electron backscattering Kikuchi diffraction patterns (BKDP) reveal useful information about the structure and orientation of crystals under study. With the well focused electron beam in a scanning electron microscope (SEM), one can use BKDP as a microanalysis tool. BKDPs have been recorded in SEMs using a phosphor screen coupled to an intensified TV camera through a lens system, and by photographic negatives. With the development of fiber-optically coupled slow scan CCD (SSC) cameras for electron beam imaging, one can take advantage of their high sensitivity and wide dynamic range for observing BKDP in SEM.We have used the Gatan 690 SSC camera to observe backscattering patterns in a JEOL JSM-840A SEM. The CCD sensor has an active area of 13.25 mm × 8.83 mm and 576 × 384 pixels. The camera head, which consists of a single crystal YAG scintillator fiber optically coupled to the CCD chip, is located inside the SEM specimen chamber. The whole camera head is cooled to about -30°C by a Peltier cooler, which permits long integration times (up to 100 seconds).

Download Full-text