Computational study of flowfield characteristics in cavities with stores

2011 ◽  
Vol 115 (1173) ◽  
pp. 669-681 ◽  
Author(s):  
B. Khanal ◽  
K. Knowles ◽  
A. J. Saddington
Keyword(s):  
Unsteady Flow ◽  
Computational Study ◽  
Three Dimensional ◽  
Scale Model ◽  
Detached Eddy Simulation ◽  
Mean Flow ◽  
Eddy Simulation ◽  
The Mean ◽  
Spanwise Flow ◽  
Flow Study

Abstract In this paper, the results of computational studies on the unsteady flow features in three-dimensional empty cavities and cavities with a representative store are presented. Flow simulations with a turbulence model based on a hybrid method, which behaves as a standard Reynolds-averaged Navier-Stokes (RANS) model within the attached boundary layer and as a Large-Eddy Simulation LES sub-grid scale model in the rest of the flow (commonly known as Detached-Eddy Simulation (DES)) are used in this study. The time-mean flow study showed the presence of three-dimensional effects inside the cavities. The mean flowfield visualisation also clearly showed the presence of a pair of ‘tornado-like’ vortices in the upstream half of the cavity which merge to a single, large recirculation further downstream. Visualisation for the cavity-with-store case revealed that the mean flowfield was effectively divided into two halves with significant reduction of the spanwise flow across the cavity width. In the unsteady flow study, near-field acoustic spectra were computed for the empty cavity and cavity-with-store cases. Study of unsteady pressure spectra for the cavity-with-store case found the presence of many peaks and the corresponding mode frequencies were found to agree well with the Rossiter modes. The blockage effect of store and strut on the spanwise flow is thought to have reduced the interaction, and subsequent non-linear coupling, between the Rossiter modes. This may be the reason for the co-existence of multiple modes without the coupling among them.

Computational Study of a Target Fluidic Flowmeter

2010 ◽  
Author(s):  
Andrzej F. Nowakowski ◽  
Franck C. G. A. Nicolleau ◽  
S. M. Muztaba Salim
Keyword(s):  
Reynolds Number ◽  
Computational Study ◽  
Numerical Technique ◽  
Three Dimensional ◽  
Boundary Layer Separation ◽  
Structure Design ◽  
Design Parameters ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Wide Range

The computational studies on the flow structure, design and performance of a target fluidic flowmeter have been carried out. The computational challenge was to find a universal approach to study a wide range of flow regimes. To this end the Detached Eddy Simulation (DES) approach for unsteady flows was applied. The numerical technique enabled to accurately reproduced three dimensional flow structures in a target fluidic flowmeter. The signal analysis of the obtained results was conducted for a range of Reynolds numbers from laminar case up to 4000. The results show that a number of factors such as meter geometry and aspect ratio can influence the performance of the flow meter significantly. A minimum Reynolds number constraint for the measurements to be accurate was evaluated for various design parameters. The significance of using knife edges which influence boundary layer separation was also established. The experimental data, which were obtained for a prototype of flowmeter setup were used to validate numerical tools in the important area of low Reynolds number flows.

scholarly journals Experimental and Computational Study of the Unsteady Flow in a 1.5 Stage Axial Turbine With Emphasis on the Secondary Flow in the Second Stator

1998 ◽  
Author(s):  
Ralf E. Walraevens ◽  
Heinz E. Gallus ◽  
Alexander R. Jung ◽  
Jürgen F. Mayer ◽  
Heinz Stetter
Keyword(s):  
Unsteady Flow ◽  
Secondary Flow ◽  
Computational Study ◽  
Three Dimensional ◽  
Cross Flow ◽  
Axial Flow ◽  
Time Dependent ◽  
Flow Structures ◽  
Mean Flow ◽  
Dependent Flow

A study of the unsteady flow in an axial flow turbine stage with a second stator blade row is presented. The low aspect ratio blades give way to a highly three-dimensional flow which is dominated by secondary flow structures. Detailed steady and unsteady measurements throughout the machine and unsteady flow simulations which include all blade rows have been carried out. The presented results focus on the second stator flow. Secondary flow structures and their origins are identified and tracked on their way through the passage. The results of the time-dependent secondary velocity vectors as well as flow angles and Mach number distributions as perturbation from the time-mean flow field are shown in cross-flow sections and azimuthal cuts throughout the domain of the second stator. At each location the experimental and numerical results are compared and discussed. A good overall agreement in the time-dependent flow behaviour as well as in the secondary flow structures is stated.

Numerical Solutions for Unsteady Subsonic Vortical Flows Around Loaded Cascades

1993 ◽  
Vol 115 (4) ◽  
pp. 810-816 ◽  
Author(s):  
J. Fang ◽  
H. M. Atassi
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Numerical Solutions ◽  
Three Dimensional ◽  
Frequency Range ◽  
Mean Flow ◽  
Vortical Flows ◽  
Unsteady Aerodynamic ◽  
Reduced Frequency ◽  
The Mean

A frequency domain linearized unsteady aerodynamic analysis is presented for three-dimensional unsteady vortical flows around a cascade of loaded airfoils. The analysis fully accounts for the distortion of the impinging vortical disturbances by the mean flow. The entire unsteady flow field is calculated in response to upstream three-dimensional harmonic disturbances. Numerical results are presented for two standard cascade configurations representing turbine and compressor bladings for a reduced frequency range from 0.1 to 5. Results show that the upstream gust conditions and blade sweep strongly affect the unsteady blade response.

Assessment of Predictive Capabilities of Detached Eddy Simulation to Simulate Flow and Mass Transport Past Open Cavities

2007 ◽  
Vol 129 (11) ◽  
pp. 1372-1383 ◽  
Author(s):  
Kyoungsik Chang ◽  
George Constantinescu ◽  
Seung-O Park
Keyword(s):  
Reynolds Number ◽  
Shear Layer ◽  
Transport Model ◽  
Detached Eddy Simulation ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Mean Velocity ◽  
Eddy Simulation ◽  
Fine Mesh ◽  
The Mean

The three-dimensional (3D) incompressible flow past an open cavity in a channel is predicted using the Spalart–Almaras (SA) and the shear-stress-transport model (SST) based versions of detached eddy simulation (DES). The flow upstream of the cavity is fully turbulent. In the baseline case the length to depth (L∕D) ratio of the cavity is 2 and the Reynolds number ReD=3360. Unsteady RANS (URANS) is performed to better estimate the performance of DES using the same code and meshes employed in DES. The capabilities of DES and URANS to predict the mean flow, velocity spectra, Reynolds stresses, and the temporal decay of the mass of a passive contaminant introduced instantaneously inside the cavity are assessed based on comparisons with results from a well resolved large eddy simulation (LES) simulation of the same flow conducted on a very fine mesh and with experimental data. It is found that the SA-DES simulation with turbulent fluctuations at the inlet gives the best overall predictions for the flow statistics and mass exchange coefficient characterizing the decay of scalar mass inside the cavity. The presence of inflow fluctuations in DES is found to break the large coherence of the vortices shed in the separated shear layer that are present in the simulations with steady inflow conditions and to generate a wider range of 3D eddies inside the cavity, similar to LES. The predictions of the mean velocity field from URANS and DES are similar. However, URANS predictions show poorer agreement with LES and experiment compared to DES for the turbulence quantities. Additionally, simulations with a higher Reynolds number (ReD=33,600) and with a larger length to depth ratio (L∕D=4) are conducted to study the changes in the flow and shear-layer characteristics, and their influence on the ejection of the passive contaminant from the cavity.

scholarly journals Numerical Solutions for Unsteady Subsonic Vortical Flows Around Loaded Cascades

1992 ◽  
Author(s):  
J. Fang ◽  
H. M. Atassi
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Numerical Solutions ◽  
Three Dimensional ◽  
Frequency Range ◽  
Mean Flow ◽  
Vortical Flows ◽  
Unsteady Aerodynamic ◽  
Reduced Frequency ◽  
The Mean

A frequency domain linearized unsteady aerodynamic analysis is presented for three-dimensional unsteady vortical flows around a cascade of loaded airfoils. The analysis fully accounts for the distortion of the impinging vortical disturbances by the mean flow. The entire unsteady flow field is calculated in response to upstream three-dimensional harmonic disturbances. Numerical results are presented for two standard cascade configurations representing turbine and compressor bladings for a reduced frequency range from 0.1 to 5. Results show that the upstream gust conditions and blade sweep strongly affect the unsteady blade response.

Numerical Study of the Mean and Filtered Characteristics of Turbulent Jets Impinging on Convex and Flat Surfaces Using LES

2012 ◽  
Author(s):  
Adra Benhacine ◽  
Zoubir Nemouchi ◽  
Lyes Khezzar ◽  
Nabil Kharoua
Keyword(s):  
Convex Surface ◽  
Numerical Study ◽  
Three Dimensional ◽  
Turbulent Jets ◽  
Scale Model ◽  
Wall Jet ◽  
Potential Core ◽  
Flat Surfaces ◽  
Free Jet ◽  
Eddy Simulation

A numerical study of a turbulent plane jet impinging on a convex surface and on a flat surface is presented, using the large eddy simulation approach and the Smagorinski-Lilly sub-grid-scale model. The effects of the wall curvature on the unsteady filtered, and the steady mean, parameters characterizing the dynamics of the wall jet are addressed in particular. In the free jet upstream of the impingement region, significant and fairly ordered velocity fluctuations, that are not turbulent in nature, are observed inside the potential core. Kelvin-Helmholtz instabilities in the shear layer between the jet and the surrounding air are detected in the form of wavy sheets of vorticity. Rolled up vortices are detached from these sheets in a more or less periodic manner, evolving into distorted three dimensional structures. Along the wall jet the Coanda effect causes a marked suction along the convex surface compared with the flat one. As a result, relatively important tangential velocities and a stretching of sporadic streamwise vortices are observed, leading to friction coefficient values on the curved wall higher than those on the flat wall.

An Investigation of Flow Fields Over Multi-Element Aerofoils

2001 ◽  
Vol 124 (1) ◽  
pp. 154-165 ◽  
Author(s):  
S. R. Maddah ◽  
H. H. Bruun
Keyword(s):  
Flow Field ◽  
Computational Study ◽  
Separated Flow ◽  
Mean Flow ◽  
Model Configuration ◽  
Attached Flow ◽  
The Mean ◽  
Flap Deflection ◽  
Comparative Results ◽  
Lift And Drag

This paper presents results obtained from a combined experimental and computational study of the flow field over a multi-element aerofoil with and without an advanced slat. Detailed measurements of the mean flow and turbulent quantities over a multi-element aerofoil model in a wind tunnel have been carried out using stationary and flying hot-wire (FHW) probes. The model configuration which spans the test section 600mm×600mm, is made of three parts: 1) an advanced (heel-less) slat, 2) a NACA 4412 main aerofoil and 3) a NACA 4415 flap. The chord lengths of the elements were 38, 250 and 83 mm, respectively. The results were obtained at a chord Reynolds number of 3×105 and a free Mach number of less than 0.1. The variations in the flow field are explained with reference to three distinct flow field regimes: attached flow, intermittent separated flow, and separated flow. Initial comparative results are presented for the single main aerofoil and the main aerofoil with a nondeflected flap at angles of attacks of 5, 10, and 15 deg. This is followed by the results for the three-element aerofoil with emphasis on the slat performance at angles of attack α=10, 15, 20, and 25 deg. Results are discussed both for a nondeflected flap δf=0deg and a deflected flap δf=25deg. The measurements presented are combined with other related aerofoil measurements to explain the main interaction of the slat/main aerofoil and main aerofoil/flap both for nondeflected and deflected flap conditions. These results are linked to numerically calculated variations in lift and drag coefficients with angle of attack and flap deflection angle.

scholarly journals Prediction of flow and dispersion in cross–ventilated buildings

2019 ◽  
Vol 128 ◽  
pp. 05002
Author(s):  
Ali Cemal Benim ◽  
Michael Diederich ◽  
Ali Nahavandi
Keyword(s):  
Computational Analysis ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Turbulence Structure ◽  
Detached Eddy Simulation ◽  
Mean Velocity ◽  
Eddy Simulation ◽  
Large Eddy ◽  
The Mean ◽  
Grid Independence

The present paper presents a detailed computational analysis of flow and dispersion in a generic isolated single–zone buildings. First, a grid generation strategy is discussed, that is inspired by a previous computational analysis and a grid independence study. Different turbulence models are appliedincluding two-equation turbulence models, the differential Reynolds Stress Model, Detached Eddy Simulation and Zonal Large Eddy Simulation. The mean velocity and concentration fields are calculated and compared with the measurements. A satisfactory agreement with the experiments is not observed by any of the modelling approaches, indicating the highly demanding flow and turbulence structure of the problem.

scholarly journals Flow visualization using momentum and energy transport tubes and applications to turbulent flow in wind farms

2013 ◽  
Vol 715 ◽  
pp. 335-358 ◽  
Author(s):  
Johan Meyers ◽  
Charles Meneveau
Keyword(s):  
Turbulent Flow ◽  
Flow Visualization ◽  
Energy Transport ◽  
Three Dimensional ◽  
Wind Farms ◽  
Mean Flow ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Using Data ◽  
Large Wind

AbstractAs a generalization of the mass–flux based classical stream tube, the concept of momentum and energy transport tubes is discussed as a flow visualization tool. These transport tubes have the property that no fluxes of momentum or energy exist over their respective tube mantles. As an example application using data from large eddy simulation, such tubes are visualized for the mean-flow structure of turbulent flow in large wind farms, in fully developed wind-turbine-array boundary layers. The three-dimensional organization of energy transport tubes changes considerably when turbine spacings are varied, enabling the visualization of the path taken by the kinetic energy flux that is ultimately available at any given turbine within the array.

Sign in / Sign up

Export Citation Format

Share Document