scholarly journals Active and recent deformation at the Southern Alps – Ligurian basin junction

2001 ◽  
Vol 80 (3-4) ◽  
pp. 255-272 ◽  
Author(s):  
C. Larroque ◽  
N. Béthoux ◽  
E. Calais ◽  
F. Courboulex ◽  
A. Deschamps ◽  
...  
Keyword(s):  
Western Europe ◽  
Active Faults ◽  
Southern Alps ◽  
Historical Seismicity ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Geological Evidence ◽  
Reflection Data ◽  
Rate Versus ◽  
Ligurian Basin

AbstractThe Southern Alps – Ligurian basin junction is one of the most active seismic areas in Western Europe countries. The topographic and the structural setting of this region is complex because of (i) its position between the high topography of the Southern Alps and the deep, narrow Ligurian oceanic basin, and (ii) the large number of structures inherited from the Alpine orogeny. Historical seismicity reveals about twenty moderate-size earthquakes (up to M=6.0), mostly distributed along the Ligurian coast and the Vésubie valley. A recent geodetic experiment shows a significant strain rate during the last 50 years in the area between the Argentera massif and the Mediterranean coastline. Results of this experiment suggest a N-S shortening of about 2-4 mm/yr over the network, this shortening direction is consistent with the seismological (P-axes of earthquakes) and the microtectonic data. The Pennic front (E-NE of the Argentera massif) and the northern Ligurian margin are the most seismically active areas. In the Nice arc and in the Argentera massif, some seismic lineaments correspond to faults identified in the field (such as theTaggia-Saorge fault or the Monaco-Sospel fault). In the western part of the Alpes Maritimes, no seismic activity is recorded in the Castellane arc. In the field, geological evidence, such as offsets of recent alluvial sediments, recent fault breccia, speleothem deformations, radon anomalies and others indicates recent deformation along these faults. Nevertheless, to this date active fault scarps have not been identified: this probably results from a relatively high erosion rate versus deformation rate and from the lack of Quaternary markers. We also suspect the presence of two hidden active faults, one in the lower Var valley (Nice city area) and the other one at the base of the Argentera crustal thrust-sheet. Offshore, along the northern Ligurian margin, the seismic reflection data shows traces of Quaternary extensional deformation, but the accuracy of the data does not yet allow the construction of a structural map nor does it allow the determination of the continuity between the offshore and onshore structures. From these data set we propose a preliminary map of 11 active faults and we discuss the questions which remain unsolved in the perspective of seismic hazard evaluations.

scholarly journals Timor Collision Front Segmentation Reveals Potential for Great Earthquakes in the Western Outer Banda Arc, Eastern Indonesia

2021 ◽  
Vol 9 ◽  
Author(s):  
Aurélie Coudurier-Curveur ◽  
Satish C. Singh ◽  
Ian Deighton
Keyword(s):  
Active Faults ◽  
Accretionary Prism ◽  
Historical Seismicity ◽  
Normal Faults ◽  
Seismic Reflection Data ◽  
Spatially Correlated ◽  
Eastern Indonesia ◽  
The North ◽  
Reflection Data ◽  
Banda Arc

In Eastern Indonesia, the western Outer Banda arc accommodates a part of the oblique Australian margin collision with Eurasia along the Timor Trough. Yet, unlike the Wetar and Alor thrusts of the Inner Banda arc in the north and the adjacent Java subduction zone in the west, both recent and historical seismicity along the Timor Trough are extremely low. This long-term seismic quiescence questions whether the Banda Arc collision front along the Timor Trough is actually fully locked or simply aseismic and raises major concerns on the possible occurrence of large magnitude and tsunamigenic earthquakes in this vulnerable and densely populated region. Here, we jointly analyze multibeam bathymetry and 2D seismic reflection data acquired along the Timor Trough to characterize the location, nature, and geometry of active faults. Discontinuous narrow folds forming a young accretionary prism at the base of the Timor wedge and spatially correlated outcropping normal faults on the bending northwest Australian shelf reveal two concurrent contrasting styles of deformation: underthrusting and frontal accretion. We find that those tectonic regimes and their associated seismic behaviors depend on 1) the thickness of the incoming and underthrusting Cenozoic sedimentary sequence, 2) the vergence of inherited normal faults developed within the continental shelf, and 3) the depth of the décollement beneath the Timor wedge. Based on the along-strike, interchanging distinct deformation style, we identify the mechanical and seismic segmentation along the Banda arc collision front and discuss the implications for earthquake and tsunami hazards along the western Outer Banda arc region.

Shallow seismic reflection study of a glaciated valley

Geophysics ◽  
1998 ◽  
Vol 63 (4) ◽  
pp. 1395-1407 ◽  
Author(s):  
Frank Büker ◽  
Alan G. Green ◽  
Heinrich Horstmeyer
Keyword(s):  
Seismic Reflection ◽  
High Amplitude ◽  
Data Sets ◽  
Seismic Section ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Northern Switzerland ◽  
Reflection Data ◽  
Shallow Seismic ◽  
Glaciated Valley

Shallow seismic reflection data were recorded along two long (>1.6 km) intersecting profiles in the glaciated Suhre Valley of northern Switzerland. Appropriate choice of source and receiver parameters resulted in a high‐fold (36–48) data set with common midpoints every 1.25 m. As for many shallow seismic reflection data sets, upper portions of the shot gathers were contaminated with high‐amplitude, source‐generated noise (e.g., direct, refracted, guided, surface, and airwaves). Spectral balancing was effective in significantly increasing the strength of the reflected signals relative to the source‐generated noise, and application of carefully selected top mutes ensured guided phases were not misprocessed and misinterpreted as reflections. Resultant processed sections were characterized by distributions of distinct seismic reflection patterns or facies that were bounded by quasi‐continuous reflection zones. The uppermost reflection zone at 20 to 50 ms (∼15 to ∼40 m depth) originated from a boundary between glaciolacustrine clays/silts and underlying glacial sands/gravels (till) deposits. Of particular importance was the discovery that the deepest part of the valley floor appeared on the seismic section at traveltimes >180 ms (∼200 m), approximately twice as deep as expected. Constrained by information from boreholes adjacent to the profiles, the various seismic units were interpreted in terms of unconsolidated glacial, glaciofluvial, and glaciolacustrine sediments deposited during two principal phases of glaciation (Riss at >100 000 and Würm at ∼18 000 years before present).

Migration with reduced artifacts from internal multiple reflections

Geophysics ◽  
2020 ◽  
Vol 85 (4) ◽  
pp. A25-A29
Author(s):  
Lele Zhang
Keyword(s):  
Seismic Reflection ◽  
Computational Cost ◽  
Data Sets ◽  
Square Root ◽  
Multiple Reflections ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Reflection Data ◽  
Recent Developments ◽  
Multiple Elimination

Migration of seismic reflection data leads to artifacts due to the presence of internal multiple reflections. Recent developments have shown that these artifacts can be avoided using Marchenko redatuming or Marchenko multiple elimination. These are powerful concepts, but their implementation comes at a considerable computational cost. We have derived a scheme to image the subsurface of the medium with significantly reduced computational cost and artifacts. This scheme is based on the projected Marchenko equations. The measured reflection response is required as input, and a data set with primary reflections and nonphysical primary reflections is created. Original and retrieved data sets are migrated, and the migration images are multiplied with each other, after which the square root is taken to give the artifact-reduced image. We showed the underlying theory and introduced the effectiveness of this scheme with a 2D numerical example.

Shallow 3D seismic-reflection imaging of fracture zones in crystalline rock

Geophysics ◽  
2007 ◽  
Vol 72 (6) ◽  
pp. B149-B160 ◽  
Author(s):  
Cedric Schmelzbach ◽  
Heinrich Horstmeyer ◽  
Christopher Juhlin
Keyword(s):  
Seismic Reflection ◽  
Crystalline Rock ◽  
Three Dimensions ◽  
Disposal Site ◽  
3D Seismic ◽  
Fracture Zones ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Reflection Data ◽  
Receiver Array

A limited 3D seismic-reflection data set was used to map fracture zones in crystalline rock for a nuclear waste disposal site study. Seismic-reflection data simultaneously recorded along two roughly perpendicular profiles (1850 and [Formula: see text] long) and with a [Formula: see text] receiver array centered at the intersection of the lines sampled a [Formula: see text] area in three dimensions. High levels of source-generated noise required a processing sequence involving surface-consistent deconvolution, which effectively increased the strength of reflected signals, and a linear [Formula: see text] filtering scheme to suppress any remaining direct [Formula: see text]-wave energy. A flexible-binning scheme significantly balanced and increased the CMP fold, but the offset and azimuth distributions remain irregular; a wide azimuth range and offsets [Formula: see text] are concentrated in the center of the survey area although long offsets [Formula: see text] are only found at the edges of the site. Three-dimensional dip moveout and 3D poststack migration were necessary to image events with conflicting dips up to about 40°. Despite the irregular acquisition geometry and the high level of source-generated noise, we obtained images rich in structural detail. Seven continuous to semicontinuous reflection events were traced through the final data volume to a maximum depth of around [Formula: see text]. Previous 2D seismic-reflection studies and borehole data indicate that fracture zones are the most likely cause of the reflections.

Minimizing field operations in shallow 3‐D seismic reflection surveying

Geophysics ◽  
2001 ◽  
Vol 66 (6) ◽  
pp. 1761-1773 ◽  
Author(s):  
Roman Spitzer ◽  
Alan G. Green ◽  
Frank O. Nitsche
Keyword(s):  
Seismic Reflection ◽  
Cost Effective ◽  
Unconsolidated Sediments ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Northern Switzerland ◽  
Shallow Subsurface ◽  
Reflection Data ◽  
Effective Manner ◽  
Original Survey

By appropriately decimating a comprehensive shallow 3‐D seismic reflection data set recorded across unconsolidated sediments in northern Switzerland, we have investigated the potential and limitations of four different source‐receiver acquisition patterns. For the original survey, more than 12 000 shots and 18 000 receivers deployed on a [Formula: see text] grid resulted in common midpoint (CMP) data with an average fold of ∼40 across a [Formula: see text] area. A principal goal of our investigation was to determine an acquisition strategy capable of producing reliable subsurface images in a more efficient and cost‐effective manner. Field efforts for the four tested acquisition strategies were approximately 50%, 50%, 25%, and 20% of the original effort. All four data subsets were subjected to a common processing sequence. Static corrections, top‐mute functions, and stacking velocities were estimated individually for each subset. Because shallow reflections were difficult to discern on shot and CMP gathers generated with the lowest density acquisition pattern (20% field effort) such that dependable top‐mute functions could not be estimated, data resulting from this acquisition pattern were not processed to completion. Of the three fully processed data subsets, two (50% field effort and 25% field effort) yielded 3‐D migrated images comparable to that derived from the entire data set, whereas the third (50% field effort) resulted in good‐quality images only in the shallow subsurface because of a lack of far‐offset data. On the basis of these results, we concluded that all geological objectives associated with our particular study site, which included mapping complex lithological units and their intervening shallow dipping boundaries, would have been achieved by conducting a 3‐D seismic reflection survey that was 75% less expensive than the original one.

scholarly journals Reconstructing the primary reflections in seismic data by Marchenko redatuming and convolutional interferometry

Geophysics ◽  
2016 ◽  
Vol 81 (2) ◽  
pp. Q15-Q26 ◽  
Author(s):  
Giovanni Angelo Meles ◽  
Kees Wapenaar ◽  
Andrew Curtis
Keyword(s):  
Velocity Model ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Surface Reflection ◽  
Reflection Data ◽  
Reference Velocity ◽  
Time Migration ◽  
Recorded Data

State-of-the-art methods to image the earth’s subsurface using active-source seismic reflection data involve reverse time migration. This and other standard seismic processing methods such as velocity analysis provide best results only when all waves in the data set are primaries (waves reflected only once). A variety of methods are therefore deployed as processing to predict and remove multiples (waves reflected several times); however, accurate removal of those predicted multiples from the recorded data using adaptive subtraction techniques proves challenging, even in cases in which they can be predicted with reasonable accuracy. We present a new, alternative strategy to construct a parallel data set consisting only of primaries, which is calculated directly from recorded data. This obviates the need for multiple prediction and removal methods. Primaries are constructed by using convolutional interferometry to combine the first-arriving events of upgoing and direct-wave downgoing Green’s functions to virtual receivers in the subsurface. The required upgoing wavefields to virtual receivers are constructed by Marchenko redatuming. Crucially, this is possible without detailed models of the earth’s subsurface reflectivity structure: Similar to the most migration techniques, the method only requires surface reflection data and estimates of direct (nonreflected) arrivals between the virtual subsurface sources and the acquisition surface. We evaluate the method on a stratified synclinal model. It is shown to be particularly robust against errors in the reference velocity model used and to improve the migrated images substantially.

scholarly journals Geodynamic and seismotectonic model of a long-lived transverse structure: The Schio-Vicenza Fault System (NE Italy)

Solid Earth ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 1967-1986
Author(s):  
Dario Zampieri ◽  
Paola Vannoli ◽  
Pierfrancesco Burrato
Keyword(s):  
Active Faults ◽  
Strike Slip ◽  
Southern Alps ◽  
Fault System ◽  
Thrust Belt ◽  
Geological Evidence ◽  
Slip Activity ◽  
Seismological Data ◽  
Moderate Seismicity ◽  
Northern Segment

Abstract. We make a thorough review of geological and seismological data on the long-lived Schio-Vicenza Fault System (SVFS) in northern Italy and present for it a geodynamic and seismotectonic interpretation. The SVFS is a major and high-angle structure transverse to the mean trend of the eastern Southern Alps fold-and-thrust belt, and the knowledge of this structure is deeply rooted in the geological literature and spans more than a century and a half. The main fault of the SVFS is the Schio-Vicenza Fault (SVF), which has a significant imprint in the landscape across the eastern Southern Alps and the Veneto-Friuli foreland. The SVF can be divided into a northern segment, extending into the chain north of Schio and mapped up to the Adige Valley, and a southern one, coinciding with the SVF proper. The latter segment borders to the east the Lessini Mountains, Berici Mountains and Euganei Hills block, separating this foreland structural high from the Veneto-Friuli foreland, and continues southeastward beneath the recent sediments of the plain via the blind Conselve–Pomposa fault. The structures forming the SVFS have been active with different tectonic phases and different styles of faulting at least since the Mesozoic, with a long-term dip-slip component of faulting well defined and, on the contrary, the horizontal component of the movement not being well constrained. The SVFS interrupts the continuity of the eastern Southern Alps thrust fronts in the Veneto sector, suggesting that it played a passive role in controlling the geometry of the active thrust belt and possibly the current distribution of seismic release. As a whole, apart from moderate seismicity along the northern segment and few geological observations along the southern one, there is little evidence to constrain the recent activity of the SVFS. In this context, the SVFS, and specifically its SVF strand, has accommodated a different amount of shortening of adjacent domains of the Adriatic (Dolomites) indenter by internal deformation produced by lateral variation in strength, related to Permian–Mesozoic tectonic structures and paleogeographic domains. The review of the historical and instrumental seismicity along the SVFS shows that it does not appear to have generated large earthquakes during the last few hundred years. The moderate seismicity points to a dextral strike-slip activity, which is also corroborated by the field analysis of antithetic Riedel structures of the fault cropping out along the northern segment. Conversely, the southern segment shows geological evidence of sinistral strike-slip activity. The apparently conflicting geological and seismological data can be reconciled considering the faulting style of the southern segment as driven by the indentation of the Adriatic plate, while the opposite style along the northern segment can be explained in a sinistral opening “zipper” model, where intersecting pairs of simultaneously active faults with a different sense of shear merge into a single fault system.

scholarly journals Using Seismic Attributes in seismotectonic research: an application to the Norcia's Mw = 6.5 earthquake (30th October 2016) in Central Italy

2019 ◽  
Author(s):  
Maurizio Ercoli ◽  
Emanuele Forte ◽  
Massimiliano Porreca ◽  
Ramon Carbonell ◽  
Cristina Pauselli ◽  
...  
Keyword(s):  
Seismic Reflection ◽  
Central Italy ◽  
Seismic Attributes ◽  
Seismic Attribute ◽  
Data Set ◽  
Epicentral Zone ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Reflection Data ◽  
Attribute Analysis

Abstract. In seismotectonic studies, seismic reflection data are a powerful tool to unravel the complex deep architecture of active faults. Such tectonic structures are usually mapped at surface through traditional geological surveying whilst seismic reflection data may help to trace their continuation from the near-surface down to hypocentral depth. In this study, we propose the application of the seismic attributes technique, commonly used in seismic reflection exploration by oil industry, to seismotectonic research for the first time. The study area is a geologically complex region of Central Italy, recently struck by a long-lasting seismic sequence including a Mw 6.5 main-shock. A seismic reflection data-set consisting of three vintage seismic profiles, currently the only available across the epicentral zone, constitutes a singular opportunity to attempt a seismic attribute analysis. This analysis resulted in peculiar seismic signatures which generally correlate with the exposed surface geologic features, and also confirming the presence of other debated structures. These results are critical, because provide information also on the relatively deep structural setting, mapping a prominent, high amplitude regional reflector that marks the top basement, interpreted as important rheological boundary. Complex patterns of high-angle discontinuities crossing the reflectors have been also identified. These dipping fabrics are interpreted as the expression of fault zones, belonging to the active normal fault systems responsible for the seismicity of the region. This work demonstrates that seismic attribute analysis, even if used on low-quality vintage 2D data, may contribute to improve the subsurface geological interpretation of areas characterized by high seismic potential.

scholarly journals Time-lapse imaging using 3D ultra-high-frequency marine seismic reflection data

Geophysics ◽  
2020 ◽  
Vol 85 (2) ◽  
pp. P13-P25
Author(s):  
Michael J. Faggetter ◽  
Mark E. Vardy ◽  
Justin K. Dix ◽  
Jonathan M. Bull ◽  
Timothy J. Henstock
Keyword(s):  
High Frequency ◽  
Seismic Reflection ◽  
High Tide ◽  
Time Lapse ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Ultra High Frequency ◽  
Reflection Data ◽  
Marine Seismic

Time-lapse (4D) seismic imaging is now widely used as a tool to map and interpret changes in deep reservoirs as well as investigate dynamic, shallow hydrological processes in the near surface. However, there are very few examples of time-lapse analysis using ultra-high-frequency (UHF; kHz range) marine seismic reflection data. Exacting requirements for navigation can be prohibitive for acquiring coherent, true-3D volumes. Variable environmental noise can also lead to poor amplitude repeatability and make it difficult to identify differences that are related to real physical changes. Overcoming these challenges opens up a range of potential applications for monitoring the subsurface at decimetric resolution, including geohazards, geologic structures, as well as the bed-level and subsurface response to anthropogenic activities. Navigation postprocessing was incorporated to improve the acquisition and processing workflow for the 3D Chirp subbottom profiler and provide stable, centimeter-level absolute positioning, resulting in well-matched 3D data and mitigating 4D noise for data stacked into [Formula: see text] common-midpoint bins. Within an example 4D data set acquired on the south coast of the UK, interpretable differences are recorded within a shallow gas blanket. Reflections from the top and bottom of a gas pocket are imaged at low tide, whereas at high tide only the upper reflection is imaged. This case study demonstrates the viability of time-lapse UHF 3D seismic reflection for quantitative mapping of decimeter-scale changes within the shallow marine subsurface.

Sign in / Sign up

Export Citation Format

Share Document