A note on the two-stream instability

1968 ◽  
Vol 2 (1) ◽  
pp. 85-91 ◽  
Author(s):  
P. C. Clemmow
Keyword(s):  
Density Ratio ◽  
Single Component ◽  
Velocity Spread ◽  
Velocity Difference ◽  
Mean Velocity ◽  
Longitudinal Waves ◽  
The Mean ◽  
Stream Instability

Conditions for the instability of longitudinal waves in a single-component two-stream plasma, in which the streams have the same velocity spread, are given in the form of simple relations between the density ratio and the mean velocity difference of the streams.

Turbulence measurements in axisymmetric jets of air and helium. Part 2. Helium jet

1993 ◽  
Vol 246 ◽  
pp. 225-247 ◽  
Author(s):  
N. R. Panchapakesan ◽  
J. L. Lumley
Keyword(s):  
Density Ratio ◽  
Effective Diameter ◽  
Mean Velocity ◽  
Velocity Fluctuations ◽  
Air Jet ◽  
Plume Region ◽  
Turbulent Schmidt Number ◽  
Radial Profiles ◽  
The Mean ◽  
Mean Concentration

A turbulent round jet of helium was studied experimentally using a composite probe consisting of an interference probe of the Way–Libby type and an × -probe. Simultaneous measurements of two velocity components and helium mass fraction concentration were made in the x/d range 50–120. These measurements are compared with measurements in an air jet of the same momentum flux reported in Part 1. The jet discharge Froude number was 14000 and the measurement range was in the intermediate region between the non-buoyant jet region and the plume region. The measurements are consistent with earlier studies on helium jets. The mass flux of helium across the jet is within ±10% of the nozzle input. The mean velocity field along the axis of the jet is consistent with the scaling expressed by the effective diameter but the mean concentration decay constant exhibits a density-ratio dependence. The radial profiles of mean velocity and mean concentration agree with earlier measurements, with the half-widths indicating a turbulent Schmidt number of 0.7. Significantly higher intensities of axial velocity fluctuations are observed in comparison with the air jet, while the intensities of radial and azimuthal velocity fluctuations are virtually identical with the air jet when scaled with the half-widths. Approximate budgets for the turbulent kinetic energy, scalar variance and scalar fluxes are presented. The ratio of mechanical to scalar timescales is found to be close to 1.5 across most of the jet. Current models for triple moments involving scalar fluctuations are compared with measurements. As was observed with the velocity triple moments in Part 1, the performance of the Full model that includes all terms except advection was found to be very good in the fully turbulent region of the jet.

Compressibility effects in a turbulent annular mixing layer. Part 1. Turbulence and growth rate

2000 ◽  
Vol 421 ◽  
pp. 229-267 ◽  
Author(s):  
JONATHAN B. FREUND ◽  
SANJIVA K. LELE ◽  
PARVIZ MOIN
Keyword(s):  
Growth Rate ◽  
Mach Number ◽  
Mixing Layer ◽  
Mixing Layers ◽  
Velocity Difference ◽  
Mean Velocity ◽  
The Mean ◽  
Mach Numbers ◽  
High Mach ◽  
Compressibility Effects

This work uses direct numerical simulations of time evolving annular mixing layers, which correspond to the early development of round jets, to study compressibility effects on turbulence in free shear flows. Nine cases were considered with convective Mach numbers ranging from Mc = 0.1 to 1.8 and turbulence Mach numbers reaching as high as Mt = 0.8.Growth rates of the simulated mixing layers are suppressed with increasing Mach number as observed experimentally. Also in accord with experiments, the mean velocity difference across the layer is found to be inadequate for scaling most turbulence statistics. An alternative scaling based on the mean velocity difference across a typical large eddy, whose dimension is determined by two-point spatial correlations, is proposed and validated. Analysis of the budget of the streamwise component of Reynolds stress shows how the new scaling is linked to the observed growth rate suppression. Dilatational contributions to the budget of turbulent kinetic energy are found to increase rapidly with Mach number, but remain small even at Mc = 1.8 despite the fact that shocklets are found at high Mach numbers. Flow visualizations show that at low Mach numbers the mixing region is dominated by large azimuthally correlated rollers whereas at high Mach numbers the flow is dominated by small streamwise oriented structures. An acoustic timescale limitation for supersonically deforming eddies is found to be consistent with the observations and scalings and is offered as a possible explanation for the decrease in transverse lengthscale.

scholarly journals Effects of Mean Flow Profiles on the Instability of a Low-Density Gas Jet Injected Into a High-Density Gas

Volume 1 ◽  
2004 ◽  
Author(s):  
Nanda Kishore Vedantam ◽  
Ramkumar N. Parthasarathy
Keyword(s):  
Shear Layer ◽  
Froude Number ◽  
Density Ratio ◽  
Critical Density ◽  
Velocity Profiles ◽  
High Density ◽  
Low Density ◽  
Mean Flow ◽  
Mean Velocity ◽  
The Mean

The effects of the mean velocity profiles on the instability characteristics in the near-injector region of axisymmetric low-density gas jets injected vertically upwards into a high-density gas medium were investigated using linear inviscid stability analysis. The flow was assumed to be isothermal and locally parallel. Three velocity profiles, signifying different changes in the mean velocity in the shear layer, were used in the analysis. The effects of the inhomogeneous shear layer and the Froude number (signifying the effects of gravity) on the instability for each set of mean profiles were delineated. At a large Froude number (negligible gravity), a critical density ratio was found for the three profiles at which the jet became absolutely unstable. The critical density ratio for each velocity profile was increased as the Froude number was reduced. A critical Froude number was found for the three sets of profiles, below which the jet was absolutely unstable for all the density ratios less than unity, which demarcated the jet flow into the momentum-driven regime and the buoyancy-driven regime.

The forced mixing layer between parallel streams

1982 ◽  
Vol 123 ◽  
pp. 91-130 ◽  
Author(s):  
D. Oster ◽  
I. Wygnanski
Keyword(s):  
Turbulent Mixing ◽  
Mixing Layer ◽  
Resonance Region ◽  
Spreading Rate ◽  
Initial Energy ◽  
Two Dimensional ◽  
Velocity Difference ◽  
Mean Velocity ◽  
Order Of Magnitude ◽  
The Mean

The effect of periodic two-dimensional excitation on the development of a turbulent mixing region was studied experimentally. Controlled oscillations of variable ampli- tude and frequency were applied at the initiation of mixing between two parallel air streams. The frequency of forcing was at least an order of magnitude lower than the initial instability frequency of the flow in order to test its effect far downstream. The effect of the velocity difference between the streams was also investigated in this experiment. A typical Reynolds number based on the velocity difference and the momentum thickness of the shear layer was l04.It was determined that the spreading rate of the mixing layer is sensitive to periodic surging even if the latter is so small that it does not contribute to the initial energy of the fluctuations. Oscillations at very small amplitudes tend to increase the spreading rate of the flow by enhancing the amalgamation of neighbouring eddies, but at higher amplitudes the flow resonates with the imposed oscillation. The resonance region can extend over a significant fraction of the test section depending on the Strouhal number and a dimensionless velocity-difference parameter. The flow in the resonance region consists of a single array of large, quasi-two-dimensional vortex lumps, which do not interact with one another. The exponential shape of the mean-velocity distribution is not affected in this region, but the spreading rate of the flow with increasing distance downstream is inhibited. The Reynolds stress in this region changes sign, indicating that energy is extracted from the turbulence to the mean motion; the intensity of the spanwise fluctuations is also reduced, suggesting that the flow tends to become more two-dimensional.Amalgamation of large coherent eddies is resumed beyond the resonance region, but the flow is not universally similar. There are many indications suggesting that the large eddies in the turbulent mixing layer at fairly large Re are governed by an inviscid instability.

The flow of liquid in a stream from the standard turbine impeller

1979 ◽  
Vol 44 (3) ◽  
pp. 700-710 ◽  
Author(s):  
Ivan Fořt ◽  
Hans-Otto Möckel ◽  
Jan Drbohlav ◽  
Miroslav Hrach
Keyword(s):  
Reynolds Number ◽  
Kinematic Viscosity ◽  
Momentum Flux ◽  
Relative Size ◽  
Mean Velocity ◽  
Axial Profile ◽  
The Mean ◽  
Hot Film ◽  
Turbine Impeller

Profiles of the mean velocity have been analyzed in the stream streaking from the region of rotating standard six-blade disc turbine impeller. The profiles were obtained experimentally using a hot film thermoanemometer probe. The results of the analysis is the determination of the effect of relative size of the impeller and vessel and the kinematic viscosity of the charge on three parameters of the axial profile of the mean velocity in the examined stream. No significant change of the parameter of width of the examined stream and the momentum flux in the stream has been found in the range of parameters d/D ##m <0.25; 0.50> and the Reynolds number for mixing ReM ##m <2.90 . 101; 1 . 105>. However, a significant influence has been found of ReM (at negligible effect of d/D) on the size of the hypothetical source of motion - the radius of the tangential cylindrical jet - a. The proposed phenomenological model of the turbulent stream in region of turbine impeller has been found adequate for values of ReM exceeding 1.0 . 103.

scholarly journals The mean velocity of posterior cerebral artery and basilar artery in Parkinson's disease with sleep disorders

2021 ◽  
Vol 4 ◽  
pp. 100207
Author(s):  
Muhammad Iqbal Basri ◽  
Ida Farida ◽  
Yudy Goysal ◽  
Jumraini Tammasse ◽  
Muhammad Akbar
Keyword(s):  
Parkinson’S Disease ◽  
Parkinson's Disease ◽  
Sleep Disorders ◽  
Cerebral Artery ◽  
Basilar Artery ◽  
Posterior Cerebral Artery ◽  
Mean Velocity ◽  
The Mean

scholarly journals Effect of Mean Velocity-to-Critical Velocity Ratios on Bed Topography and Incipient Motion in a Meandering Channel: Experimental Investigation

Water ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 883
Author(s):  
Nargess Moghaddassi ◽  
Seyed Habib Musavi-Jahromi ◽  
Mohammad Vaghefi ◽  
Amir Khosrojerdi
Keyword(s):  
Experimental Investigation ◽  
Critical Velocity ◽  
Velocity Ratio ◽  
Scour Depth ◽  
Incipient Motion ◽  
Mean Velocity ◽  
Straight Path ◽  
Meandering Channel ◽  
Bed Topography ◽  
The Mean

As 180-degree meanders are observed in abundance in nature, a meandering channel with two consecutive 180-degree bends was designed and constructed to investigate bed topography variations. These two 180-degree mild bends are located between two upstream and downstream straight paths. In this study, different mean velocity-to-critical velocity ratios have been tested at the upstream straight path to determine the meander’s incipient motion. To this end, bed topography variations along the meander and the downstream straight path were addressed for different mean velocity-to-critical velocity ratios. In addition, the upstream bend’s effect on the downstream bend was investigated. Results indicated that the maximum scour depth at the downstream bend increased as a result of changing the mean velocity-to-critical velocity ratio from 0.8 to 0.84, 0.86, 0.89, 0.92, 0.95, and 0.98 by, respectively, 1.5, 2.5, 5, 10, 12, and 26 times. Moreover, increasing the ratio increased the maximum sedimentary height by 3, 10, 23, 48, 49, and 56 times. The upstream bend’s incipient motion was observed for the mean velocity-to-critical velocity ratio of 0.89, while the downstream bend’s incipient motion occurred for the ratio of 0.78.

Theoretical analysis of a rolling-sliding elastohydrodynamic lubrication line contact with a subsurface inclusion

2019 ◽  
Vol 233 (8) ◽  
pp. 1197-1207
Author(s):  
Armando Félix Quiñonez ◽  
Guillermo E Morales Espejel
Keyword(s):  
Elastohydrodynamic Lubrication ◽  
Element Model ◽  
Von Mises Stress ◽  
Transient Effects ◽  
Mean Velocity ◽  
The Matrix ◽  
Soft Inclusion ◽  
The Mean ◽  
Von Mises ◽  
Fully Coupled

This work investigates the transient effects of a single subsurface inclusion over the pressure, film thickness, and von Mises stress in a line elastohydrodynamic lubrication contact. Results are obtained with a fully-coupled finite element model for either a stiff or a soft inclusion moving at the speed of the surface. Two cases analyzed consider the inclusion moving either at the same speed as the mean velocity of the lubricant or moving slower. Two additional cases investigate reducing either the size of the inclusion or its stiffness differential with respect to the matrix. It is shown that the well-known two-wave elastohydrodynamic lubrication mechanism induced by surface features is also applicable to the inclusions. Also, that the effects of the inclusion become weaker both when its size is reduced and when its stiffness approaches that of the matrix. A direct comparison with predictions by the semi-analytical model of Morales-Espejel et al. ( Proc IMechE, Part J: J Engineering Tribology 2017; 231) shows reasonable qualitative agreement. Quantitatively some differences are observed which, after accounting for the semi-analytical model's simplicity, physical agreement, and computational efficiency, may then be considered as reasonable for engineering applications.

The Estimation of Discharge in an Experimental Open Channel

2014 ◽  
Vol 905 ◽  
pp. 369-373
Author(s):  
Choo Tai Ho ◽  
Yoon Hyeon Cheol ◽  
Yun Gwan Seon ◽  
Noh Hyun Suk ◽  
Bae Chang Yeon
Keyword(s):  
Unsteady Flow ◽  
River Discharge ◽  
Open Channel ◽  
Flow Conditions ◽  
Mean Velocity ◽  
Velocity Equation ◽  
The Mean ◽  
Loop Form

The estimation of a river discharge by using a mean velocity equation is very convenient and rational. Nevertheless, a research on an equation calculating a mean velocity in a river was not entirely satisfactory after the development of Chezy and Mannings formulas which are uniform equations. In this paper, accordingly, the mean velocity in unsteady flow conditions which are shown loop form properties was estimated by using a new mean velocity formula derived from Chius 2-D velocity formula. The results showed that the proposed method was more accurate in estimating discharge, when compared with the conventional formulas.

scholarly journals Dynamic Asymmetries Do Not Match Spatiotemporal Step Asymmetries during Split-Belt Walking

Symmetry ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 1089
Author(s):  
Stefano Scarano ◽  
Luigi Tesio ◽  
Viviana Rota ◽  
Valeria Cerina ◽  
Luigi Catino ◽  
...  
Keyword(s):  
Lower Limb ◽  
Step Length ◽  
Centre Of Mass ◽  
Mean Velocity ◽  
Rehabilitation Research ◽  
Joint Dynamics ◽  
Stance Time ◽  
After Effect ◽  
The Mean ◽  
Step Parameters

While walking on split-belt treadmills (two belts running at different speeds), the slower limb shows longer anterior steps than the limb dragged by the faster belt. After returning to basal conditions, the step length asymmetry is transiently reversed (after-effect). The lower limb joint dynamics, however, were not thoroughly investigated. In this study, 12 healthy adults walked on a force-sensorised split-belt treadmill for 15 min. Belts rotated at 0.4 m s−1 on both sides, or 0.4 and 1.2 m s−1 under the non-dominant and dominant legs, respectively. Spatiotemporal step parameters, ankle power and work, and the actual mean velocity of the body’s centre of mass (CoM) were computed. On the faster side, ankle power and work increased, while step length and stance time decreased. The mean velocity of the CoM slightly decreased. As an after-effect, modest converse asymmetries developed, fading within 2–5 min. These results may help to decide which belt should be assigned to the paretic and the unaffected lower limb when split-belt walking is applied for rehabilitation research in hemiparesis.

Sign in / Sign up

Export Citation Format

Share Document