Design and analysis of CICABOT: a novel translational parallel manipulator based on two 5-bar mechanisms

Robotica ◽  
2011 ◽  
Vol 30 (3) ◽  
pp. 449-456 ◽  
Author(s):  
M. F. Ruiz-Torres ◽  
E. Castillo-Castaneda ◽  
J. A. Briones-Leon
Keyword(s):  
Parallel Manipulator ◽  
Jacobian Matrix ◽  
Geometric Analysis ◽  
Vector Equation ◽  
Prismatic Joints ◽  
Hollow Cylinders ◽  
Moving Platform ◽  
Direct Kinematics

SUMMARYThis work presents the CICABOT, a novel 3-DOF translational parallel manipulator (TPM) with large workspace. The manipulator consists of two 5-bar mechanisms connected by two prismatic joints; the moving platform is on the union of these prismatic joints; each 5-bar mechanism has two legs. The mobility of the proposed mechanism, based on Gogu approach, is also presented. The inverse and direct kinematics are solved from geometric analysis. The manipulator's Jacobian is developed from the vector equation of the robot legs; the singularities can be easily derived from Jacobian matrix. The manipulator workspace is determined from analysis of a 5-bar mechanism; the resulting workspace is the intersection of two hollow cylinders that is much larger than other TPM with similar dimensions.

Dynamic Modeling of a Parallel Manipulator With Three Translational Degrees of Freedom

1998 ◽  
Author(s):  
Richard Stamper ◽  
Lung-Wen Tsai
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Close Agreement ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Kinematic Structure ◽  
End Effector ◽  
Moving Platform ◽  
Euler Approach ◽  
Computationally Intensive

Abstract The dynamics of a parallel manipulator with three translational degrees of freedom are considered. Two models are developed to characterize the dynamics of the manipulator. The first is a traditional Lagrangian based model, and is presented to provide a basis of comparison for the second approach. The second model is based on a simplified Newton-Euler formulation. This method takes advantage of the kinematic structure of this type of parallel manipulator that allows the actuators to be mounted directly on the base. Accordingly, the dynamics of the manipulator is dominated by the mass of the moving platform, end-effector, and payload rather than the mass of the actuators. This paper suggests a new method to approach the dynamics of parallel manipulators that takes advantage of this characteristic. Using this method the forces that define the motion of moving platform are mapped to the actuators using the Jacobian matrix, allowing a simplified Newton-Euler approach to be applied. This second method offers the advantage of characterizing the dynamics of the manipulator nearly as well as the Lagrangian approach while being less computationally intensive. A numerical example is presented to illustrate the close agreement between the two models.

Geometry and Kinematic Analysis of a Redundantly Actuated Parallel Mechanism for Rehabilitation

2007 ◽  
Author(s):  
Jody A. Saglia ◽  
Jian S. Dai
Keyword(s):  
Control System ◽  
Kinematic Analysis ◽  
Parallel Mechanism ◽  
Parallel Manipulator ◽  
Jacobian Matrix ◽  
Forward Kinematics ◽  
Control System Design ◽  
Ankle Rehabilitation ◽  
Redundantly Actuated ◽  
Moving Platform

This paper presents the geometry and the kinematic analysis of a parallel manipulator developed for ankle rehabilitation, as the beginning of a control system design process. First the geometry of the parallel mechanism is described, secondly the equations for the inverse and the forward kinematics are obtained, then the forward kinematics is analyzed in order to define all the possible configurations of the moving platform. Finally the Jacobian matrix of the rig is obtained by differentiating the position equations and the singularities are investigated, comparing the non-redundant and redundant type of mechanism.

Sensitivity Analysis of Planar Parallel Manipulators

2008 ◽  
Author(s):  
Ste´phane Caro ◽  
Nicolas Binaud ◽  
Philippe Wenger
Keyword(s):  
Sensitivity Analysis ◽  
Parallel Manipulator ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Geometric Parameters ◽  
Sensitivity Coefficients ◽  
Planar Parallel Manipulator ◽  
Moving Platform ◽  
Conditioning Number ◽  
Planar Parallel Manipulators

This paper deals with the sensitivity analysis of planar parallel manipulators. A methodology is introduced to derive the sensitivity coefficients by means of the study of 3-RPR manipulators. As a matter of fact, the sensitivity coefficients of the pose of its moving platform to variations in the geometric parameters are expressed algebraically, the variations being defined both in Polar and Cartesian coordinates. The dexterity of the manipulator is also studied by means of the conditioning number of its normalized kinematic Jacobian matrix. As an illustrative example, the sensitivity of a symmetrical planar parallel manipulator is analyzed in detail. Finally, the accuracy of the manipulator is compared with its dexterity.

Direct Singular Positions of 3RPS Parallel Manipulators

2004 ◽  
Vol 126 (6) ◽  
pp. 1006-1016 ◽  
Author(s):  
C. H. Liu ◽  
Shengchia Cheng
Keyword(s):  
Circular Cylinder ◽  
Parallel Manipulator ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Second Step ◽  
Horizontal Position ◽  
Solid Cylinder ◽  
Singular Configurations ◽  
Solid Circular Cylinder ◽  
Moving Platform

In this study a procedure to obtain direct singular positions of a 3RPS parallel manipulator is presented. If the heights of three spherical joints, denoted by d1n,d2n, and d3n respectively, are used as coordinate axes, then the workspace of the moving platform may be represented as an inclined solid cylinder in this coordinate system. The location of a point on the solid circular cylinder determines a configuration of the manipulator’s moving platform. The procedure to locate direct singular positions consists of two steps, the orientation of the moving platform is assumed first, from which the horizontal position of the moving platform may be obtained. Then in the second step the heights that make determinant of the Jacobian matrix vanish may always be determined. Results show that unless the moving platform is normal to the base, in which case there exist only one or two singular configurations, otherwise there are always three singular configurations corresponding to a moving platform’s orientation.

On the kinematics of the 3-RRUR spherical parallel manipulator

Robotica ◽  
2009 ◽  
Vol 28 (6) ◽  
pp. 821-832 ◽  
Author(s):  
R. Deidda ◽  
A. Mariani ◽  
M. Ruggiu
Keyword(s):  
Parallel Manipulator ◽  
Jacobian Matrix ◽  
Mobility Analysis ◽  
Geometrical Condition ◽  
Mechanical Interference ◽  
Fixed Base ◽  
Spherical Wrist ◽  
Moving Platform ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator

SUMMARYIn the present paper, the kinematics of a three-degree-of-freedom spherical wrist is investigated. The wrist consists of a fixed base connected to a moving platform by three identical legs, each with a RRUR chain (R and U denote a revolute pair and a universal pair, respectively). For each leg, the first R pair is to be considered actuated. Although in previous works the kinematics synthesis of this architecture was carried out, no detailed studies were presented on the kinematic issues of the wrist. This paper presents the mobility analysis, the direct and inverse position kinematics, the differential kinematics of the manipulator including inspection on the jacobian matrix and the analysis of the singularities. The geometrical condition matched in case of mechanical interference between legs is addressed, too. A numerical example of the manipulator kinematics was performed to obtain the workspace, the condition number and the mechanical inteference condition.

Direct Singular Positions of 3RPS Parallel Manipulators

2004 ◽  
Author(s):  
C. H. Liu ◽  
Shengchia Cheng
Keyword(s):  
Circular Cylinder ◽  
Parallel Manipulator ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Second Step ◽  
Horizontal Position ◽  
Solid Cylinder ◽  
Singular Configurations ◽  
Solid Circular Cylinder ◽  
Moving Platform

In this study a procedure to obtain direct singular positions of a 3RPS parallel manipulator is presented. If the heights of 3 spherical joints, denoted by d1n, d2n, and d3n respectively, are used as coordinate axes, then the workspace of the moving platform may be represented as an inclined solid cylinder in this coordinate system. The location of a point on the solid circular cylinder determines a configuration of the manipulator’s moving platform. The procedure to locate direct singular positions consists of two steps, the orientation of the moving platform is assumed first, from which the horizontal position of the moving platform may be obtained; then in the second step the heights that make determinant of Jacobian matrix vanish may always be determined. Results show that unless the moving platform is normal to the base, in which case there exist only one or two singular configurations, otherwise there are always three singular configurations corresponding to a moving platform’s orientation.

Dimensionally Homogeneous Jacobian and Condition Number

2016 ◽  
Vol 836 ◽  
pp. 42-47 ◽  
Author(s):  
Latifah Nurahmi ◽  
Stéphane Caro
Keyword(s):  
Performance Analysis ◽  
Condition Number ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Moving Platform ◽  
Conditioning Number

This paper deals with the formulation of the dimensionally homogeneous extended Jacobian matrix, which is an important issue for the performance analysis of f degrees-of-freedom (f ≤6) parallel manipulators having coupled rotational and translational motions. By using the f independent coordinates to define the permitted motions and (6-f) independent coordinates to define the restricted motions of the moving platform, the 6×6 dimensionally homogeneous extended Jacobian matrix is derived for non-redundant parallel manipulators. The conditioning number of the parallel manipulators is computed to evaluate the homogeneous extended Jacobian matrix, the homogeneous actuation wrench matrix, and the homogeneous constraint wrench matrix to evaluate the performance of the parallel manipulators. By using these indices, the closeness of a pose to different singularities can be detected. An illustrative example with the 3-RPS parallel manipulator is provided to highlight the effectiveness of the approach and the proposed indices.

scholarly journals Non-Singular Assembly Mode Changing Trajectories of a 6-DOF Parallel Robot

2012 ◽  
Author(s):  
Stéphane Caro ◽  
Philippe Wenger ◽  
Damien Chablat
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Dimensional Space ◽  
Kinematic Model ◽  
Three Dimensional ◽  
Parallel Robot ◽  
Joint Space ◽  
Change Of Variables ◽  
Prismatic Joints ◽  
Moving Platform

This paper deals with the non-singular assembly mode changing of a six degrees of freedom parallel manipulator. The manipulator is composed of three identical limbs and one moving platform. Each limb is composed of three prismatic joints of directions orthogonal to each other and one spherical joint. The first two prismatic joints of each limb are actuated. The planes normal to the directions of the first two prismatic joints of each limb are orthogonal to each other. It appears that the parallel singularities of the manipulator depend only on the orientation of its moving platform. Moreover, the manipulator turns to have two aspects, namely, two maximal singularity free domains without any singular configuration, in its orientation workspace. As the manipulator can get up to eight solutions to its direct kinematic model, several assembly modes can be connected by non-singular trajectories. It is noteworthy that the images of those trajectories in the joint space of the manipulator encircle one or several cusp point(s). This property can be depicted in a three dimensional space because the singularities depend only on the orientation of the moving-platform and the mapping between the orientation parameters of the manipulator and three joint variables can be obtained with a simple change of variables. Finally to the best of the authors’ knowledge, this is the first spatial parallel manipulator for which non-singular assembly mode changing trajectories have been found and shown.

Kinematics of a New High-Precision Three-Degree-of-Freedom Parallel Manipulator

2006 ◽  
Vol 129 (3) ◽  
pp. 320-325 ◽  
Author(s):  
Farhad Tahmasebi
Keyword(s):  
Power Dissipation ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Base Plane ◽  
Degree Polynomial ◽  
Payload Capacity ◽  
Half Angle ◽  
Three Degree Of Freedom ◽  
Direct Kinematics

Closed-form direct and inverse kinematics of a new three-degree-of-freedom (DOF) parallel manipulator with inextensible limbs and base-mounted actuators are presented. The manipulator has higher resolution and precision than the existing three-DOF mechanisms with extensible limbs. Since all of the manipulator actuators are base mounted, higher payload capacity, smaller actuator sizes, and lower power dissipation can be obtained. The manipulator is suitable for alignment applications where only tip, tilt, and piston motions are significant. The direct kinematics of the manipulator is reduced to solving an eighth-degree polynomial in the square of the tangent of the half-angle between one of the limbs and the base plane. Hence, there are at most 16 assembly configurations for the manipulator. In addition, it is shown that the 16 solutions are eight pairs of reflected configurations with respect to the base plane. Numerical examples for the direct and inverse kinematics of the manipulator are also presented.

Synthesis of Parallel Manipulator with Single DOF

2013 ◽  
Vol 330 ◽  
pp. 639-643 ◽  
Author(s):  
Chung Huang Yu ◽  
Wen Yeuan Chung
Keyword(s):  
Parallel Manipulator ◽  
Design Concept ◽  
Path Generation ◽  
Dimensional Synthesis ◽  
Type Synthesis ◽  
Numerical Example ◽  
Geometrical Constraints ◽  
Moving Platform ◽  
Manipulator Design

This paper proposed a new manipulator design concept which leads to a single DOF system. The system composed of a moving platform and several supporting legs. It can execute the tasks of 3D body guidance or path generation and thus replace expensive manipulators with high DOF in some conditions. There are mainly two steps in designing this manipulator. The first step is type synthesis to determine the number and types of legs. Dimensional synthesis is then executed based on the movement requirements and geometrical constraints. In this study the reduction of the DOF is also analyzed for various legs added between the moving platform and the ground. A numerical example of executing 3D body guidance is given to verify the proposed new concept.

Sign in / Sign up

Export Citation Format

Share Document