Phase-aligned Dual-frequency Constant Envelope Multiplexing Technique for GNSS Signals

2018 ◽  
Vol 71 (4) ◽  
pp. 899-918
Author(s):  
Zhihui Zhou ◽  
Zuping Tang ◽  
Jiaolong Wei ◽  
Xuan Xia ◽  
Tao Yan

In the new generation of Global Navigation Satellite Systems (GNSS), dual-frequency constant envelope multiplexing is widely desired and is becoming an important subject in signal design. Considerable work has been devoted to multiplexing for the Alternative Binary Offset Carrier (AltBOC)-like signal model, for which each sideband consists of two or fewer signal components. In this paper, a phase-aligned dual-frequency constant envelope multiplexing technique is proposed for a general dual-frequency signal model. This multiplexing technique can be used to combine two constant-envelope-modulated signals in two sidebands into a composite signal with a constant envelope, where the constant-envelope-modulated signal in each sideband consists of an arbitrary number of signal components with an arbitrary power ratio and phase relationship among the signal components. A Lookup Table (LUT)-based signal generation method is also proposed, for which the required driving clock rate of the signal generator can be flexibly adjusted to meet the requirements of the satellite payload. Applications for the AltBOC-like signal model and a general dual-frequency signal model in the Beidou B1 band validate the flexibility and high multiplexing efficiency of our method. Specifically, AltBOC is a special case of the proposed method.

2018 ◽  
Vol 71 (6) ◽  
pp. 1511-1530
Author(s):  
Tao Yan ◽  
Bo Qu ◽  
Ying Wang ◽  
Guoyong Wang ◽  
Wenying Lei ◽  
...  

In the field of modernised Global Navigation Satellite System (GNSS) signal design, several Dual-frequency Constant Envelope Multiplexing (DCEM) methods have been recently proposed. However, the existing DCEM methods, such as Alternative Binary Offset Carrier (AltBOC), generalised AltBOC and Asymmetric Constant Envelope Binary Offset Carrier (ACE-BOC), are only applied in some special cases. In this paper, we present a unified DCEM design framework for GNSS signals. The existing DCEM methods can be unified in this framework. First, the signal components at two carrier frequencies are combined into two single-frequency constant envelope signals. Then, the linear sum of dual-frequency signals with non-constant envelopes is obtained. Finally, the linear sum is converted into the corresponding DCEM signal by solving an optimisation problem. The proposed design framework has no strict constraints on the number, power ratio and phase relationship of the signal components. Moreover, some special design cases under this framework are also analysed in detail. The analytical results show that the proposed design method can reach higher multiplexing efficiency compared with the existing methods. Based on the proposed method, we suggest a scheme to multiplex the BeiDou regional signals and global signals at the B2 frequency. The simulation results of correlation functions and Power Spectrum Density (PSD) verify the correctness and effectiveness of the proposed design method.


2021 ◽  
Author(s):  
Estel Cardellach ◽  
Weiqiang Li ◽  
Dallas Masters ◽  
Takayuki Yuasa ◽  
Franck Borde ◽  
...  

<p>Recently, different studies have shown evidence of signals transmitted by the Global Navigation Satellite Systems (GNSS), coherently reflected over some parts of the ocean, and received from cubesats. In particular, strong coherent scattering has been reported in regions with low water surface roughness as those near continental masses and in atolls. Over open ocean, few coherent signals were reported to be found, although the data sets were somewhat limited and certainly not exhaustive. The level of coherence in reflected GNSS signals depends on the roughness of the  surface (i.e. significant wave height and small scale ripples and waves induced by the wind), the viewing geometry (i.e. incidence angle, or equivalently, elevation angle of the GNSS satellite as seen from the point of reflection), propagation effects (namely ionospheric disturbances) and on the frequency (i.e. particular GNSS band, like L1/E1, L2 or L5/E5). These coherent measurements over ocean follow earlier evidence of coherent GNSS reflections over sea ice which date back to 2005, the time of UK-DMC mission. More recently, Sea Ice Thickness (SIT) retrievals have also been carried out with this technique, at an accuracy comparable to that of SMOS.</p><p>All the observations referred so far were done at a single frequency, L1/E1. So, there is an interest to explore the coherence at the other main GNSS bands, i.e. L2 and L5/E5 as well as to the widelane combinations between them (linear combinations of carrier-phase measurements, of longer effective wavelength). Spire Global radio occultation cubesats work at L1 and L2 frequency bands, and therefore provide unique dual-frequency raw data sets of reflected signals over open ocean, sea ice and inland water bodies. With these, it is possible to study the coherence of these targets at each of the bands and at their widelane combination, as well as the performance of altimetric retrievals at grazing angles of observation (very slant geometries, which facilitate coherence properties of the scattering). The dual-frequency observations can correct the ionospheric effects, and their widelane combinations, of longer effective wavelength, might expand the conditions for coherence. The fact that this new approach is fully compatible with small GNSS radio occultation payloads and missions, might represent a low cost source of precise altimetry to complement larger dedicated missions.</p><p>An ESA research study involving Spire Global and IEEC aims at studying this new potential altimetric technique. Raw data acquisitions from limb-looking antennas of Spire’s cubesat constellation were selected to be geographically and time collocated with ESA Sentinel 3A and 3B passes in order to compare the results of coherence and altimetry. For this study, the raw data at two frequencies, acquired at 6.2 Mbps, are shifted to intermediate frequencies and downloaded to the ground without any further processing. In-house software receivers are then applied to generate the reflected echoes or waveforms, and to track the phase of the carrier signals. Precise altimetry (a few cm in 20 ms integration) is then possible from these observables. The results of this activity will be shown, focusing on altimetric retrievals over large lakes.</p>


2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Alaa A. Elghazouly ◽  
Mohamed I. Doma ◽  
Ahmed A. Sedeek

Abstract Due to the ionosphere delay, which has become the dominant GPS error source, it is crucial to remove the ionospheric effect before estimating point coordinates. Therefore, different agencies started to generate daily Global Ionosphere Maps (GIMs); the Vertical Total Electron Content (VTEC) values represented in GIMs produced by several providers can be used to remove the ionosphere error from observations. In this research, An analysis will be carried with three sources for VTEC maps produced by the Center for Orbit Determination in Europe (CODE), Regional TEC Mapping (RTM), and the International Reference Ionosphere (IRI). The evaluation is focused on the effects of a specific ionosphere GIM correction on the precise point positioning (PPP) solutions. Two networks were considered. The first network consists of seven Global Navigation Satellite Systems (GNSS) receivers from (IGS) global stations. The selected test days are six days, three of them quiet, and three other days are stormy to check the influence of geomagnetic storms on relative kinematic positioning solutions. The second network is a regional network in Egypt. The results show that the calculated coordinates using the three VTEC map sources are far from each other on stormy days rather than on quiet days. Also, the standard deviation values are large on stormy days compared to those on quiet days. Using CODE and RTM IONEX file produces the most precise coordinates after that the values of IRI. The elimination of ionospheric biases over the estimated lengths of many baselines up to 1000 km has resulted in positive findings, which show the feasibility of the suggested assessment procedure.


GPS Solutions ◽  
2020 ◽  
Vol 25 (1) ◽  
Author(s):  
Francesco Darugna ◽  
Jannes B. Wübbena ◽  
Gerhard Wübbena ◽  
Martin Schmitz ◽  
Steffen Schön ◽  
...  

Abstract The access to Android-based Global Navigation Satellite Systems (GNSS) raw measurements has become a strong motivation to investigate the feasibility of smartphone-based positioning. Since the beginning of this research, the smartphone GNSS antenna has been recognized as one of the main limitations. Besides multipath (MP), the radiation pattern of the antenna is the main site-dependent error source of GNSS observations. An absolute antenna calibration has been performed for the dual-frequency Huawei Mate20X. Antenna phase center offset (PCO) and variations (PCV) have been estimated to correct for antenna impact on the L1 and L5 phase observations. Accordingly, we show the relevance of considering the individual PCO and PCV for the two frequencies. The PCV patterns indicate absolute values up to 2 cm and 4 cm for L1 and L5, respectively. The impact of antenna corrections has been assessed in different multipath environments using a high-accuracy positioning algorithm employing an undifferenced observation model and applying ambiguity resolution. Successful ambiguity resolution is shown for a smartphone placed in a low multipath environment on the ground of a soccer field. For a rooftop open-sky test case with large multipath, ambiguity resolution was successful in 19 out of 35 data sets. Overall, the antenna calibration is demonstrated being an asset for smartphone-based positioning with ambiguity resolution, showing cm-level 2D root mean square error (RMSE).


2019 ◽  
Vol 13 (1) ◽  
pp. 1-12 ◽  
Author(s):  
Manuel Bravo ◽  
Carlos Villalobos ◽  
Rodrigo Leiva ◽  
Luis Tamblay ◽  
Pedro Vega-Jorquera ◽  
...  

Objective: The diurnal variations of several ionospheric characteristics during the Space Weather Events of 4-10 September 2017, for Chilean latitudes, will be reported. Materials and Methods: Observations were made using a recently installed ionosonde at the Universidad de La Serena field station (29°52'S; 71°15’W). Also, reported is the total electron content determined using the upgraded Chilean network of dual-frequency Global Navigation Satellite Systems (GNSS) receivers. Results: Sudden ionospheric disturbances are described in terms of the minimum reflection frequency determined from ionosonde records. An attempt to derive the extent of the effect on high frequency propagation paths in the region is made using simultaneous ionosonde observations at other locations. The geomagnetic storm ionospheric effects are discussed in detail using the observed diurnal variation of maximum electron concentration (NmF2), virtual height of the F-region (h’F/F2) and Total Electron Content (TEC). These are complemented with the time-latitude variation of TEC for the 70°W meridian. Conclusion: It is found that large increases of NmF2, h’F/F2 and TEC observed during 8 September 2017 storm are well described in terms of the evolution of the Equatorial Ionospheric Anomaly (EIA) over the same time interval. Known physical mechanisms are suggested to explain most of the observations.


2018 ◽  
Vol 8 (11) ◽  
pp. 2226 ◽  
Author(s):  
Zhijun Liu ◽  
Baiyu Li ◽  
Xiangwei Zhu ◽  
Lixun Li ◽  
Guangfu Sun

The binary offset carrier (BOC) modulation, which has been adopted in modern global navigation satellite systems (GNSS), provides a higher spectral compatibility with BPSK signals, and better tracking performance. However, the autocorrelation function (ACF) of BOC signals has multiple peaks. This feature complicates the acquisition process, since a smaller time searching step is required, which results in longer searching time or greater amounts of hardware resources. Another problem is the high Nyquist frequency, which leads to high computational complexity and power consumption. In this paper, to overcome these drawbacks, the band-pass sampling technique for multiple signals is introduced to BOC signals. The sampling frequency can be reduced significantly. Furthermore, the ACF of the sampled signal has only two secondary peaks, so that the code phase can be searched with a larger searching step. An acquisition structure base on dual-loop is proposed, to completely eliminate the ambiguity and compensate the subcarrier Doppler. The acquisition performance and the computational complexity are also analysed.


2020 ◽  
Vol 55 (1) ◽  
pp. 17-28 ◽  
Author(s):  
Ashraf Abdallah ◽  
Amgad Saifeldin ◽  
Abdelhamid Abomariam ◽  
Reda Ali

AbstractIn the developing countries, cost-effective observation techniques are very important for earthwork estimation, map production, geographic information systems, and hydrographic surveying. One of the most cost-effective techniques is Precise Point Positioning (PPP); it is a Global Navigation Satellite Systems (GNSS) positioning technique to compute precise positions using only a single GNSS receiver. This study aims to evaluate the efficiency of using Global Positioning System (GPS) and GPS/ Globalnaya Navigatsionnaya Sputnikovaya Sistema (GLONASS) post-processed kinematic PPP solution for digital elevation model (DEM) production, which is used in earthwork estimation. For this purpose, a kinematic trajectory has been observed in New Aswan City in an open sky area using dual-frequency GNSS receivers. The results showed that, in case of using GPS/GLONASS PPP solution to estimate volumes, the error in earthwork volume estimation varies between 0.07% and 0.16% according to gridding level. On the other hand, the error in volume estimation from GPS PPP solution varies between 0.40% and 0.99%.


2020 ◽  
Author(s):  
Min Li ◽  
Baocheng Zhang ◽  
Xiao Zhang

<p>When sensing the Earth’s ionosphere using pseudorange observations of global navigation satellite systems (GNSS), the satellite and receiver Differential Code Biases (DCBs) account for one of the main sources of error. For the sake of convenience, Receiver DCBs (DCBs) are commonly assumed as constants over a period of one day in the traditional carrier-to-code leveling (CCL) method. Thus, remarkable intraday variability in the receiver DCBs have been ignored in the commonly-used assumption and may seriously restrict the accuracy of ionospheric observable retrieval. The Modified CCL (MCCL) method can eliminate the adverse impact of the short-term variations of RDCBs on the retrieval of ionospheric TEC. With the rapid development of the GPS, GLONASS, Galileo and BeiDou systems, there is a strong demand of precise ionospheric TEC products for multiple constellations and frequencies. Considering the existed MCCL method can only be used for dual-frequency GNSS data, in this study, we extend the two-frequency MCCL method to the multi-frequency and multi-GNSS case and further carry out a series of investigations. In our proposed method, a newly full-rank multi-frequency (more than triple frequency) model with raw observations are established to synchronously estimate both the slant ionospheric delays and the RCB offset with respect to the reference epoch at each individual frequency. Based on the test results, compared to the traditional CCL-method, the accuracy of the ionospheric TEC retrieved using our proposed method can be improved from 5.12 TECu to 0.95 TECu in the case that significant short-term variations existed in receiver DCBs. In addition, the between-epoch fluctuations experienced by receiver code biases at all frequencies tracked by a single receiver can be detected by our the proposed method, and the dependence of multi-GNSS and multi-frequency RDCB offsets upon ambient temperature further are verified in this study. Compared to Galileo system, the RDCB in BDS show higher correlation with temperature. We also found that the RDCB at different frequencies of the same system show various characteristics.</p>


Sign in / Sign up

Export Citation Format

Share Document