A Unified Dual-frequency Constant Envelope Multiplexing Design Framework for Modernised GNSS Signals

2018 ◽  
Vol 71 (6) ◽  
pp. 1511-1530
Author(s):  
Tao Yan ◽  
Bo Qu ◽  
Ying Wang ◽  
Guoyong Wang ◽  
Wenying Lei ◽  
...  
Keyword(s):  
Design Method ◽  
Phase Relationship ◽  
Satellite System ◽  
Single Frequency ◽  
Design Framework ◽  
Signal Design ◽  
Dual Frequency ◽  
Binary Offset Carrier ◽  
Constant Envelope ◽  
Special Cases

In the field of modernised Global Navigation Satellite System (GNSS) signal design, several Dual-frequency Constant Envelope Multiplexing (DCEM) methods have been recently proposed. However, the existing DCEM methods, such as Alternative Binary Offset Carrier (AltBOC), generalised AltBOC and Asymmetric Constant Envelope Binary Offset Carrier (ACE-BOC), are only applied in some special cases. In this paper, we present a unified DCEM design framework for GNSS signals. The existing DCEM methods can be unified in this framework. First, the signal components at two carrier frequencies are combined into two single-frequency constant envelope signals. Then, the linear sum of dual-frequency signals with non-constant envelopes is obtained. Finally, the linear sum is converted into the corresponding DCEM signal by solving an optimisation problem. The proposed design framework has no strict constraints on the number, power ratio and phase relationship of the signal components. Moreover, some special design cases under this framework are also analysed in detail. The analytical results show that the proposed design method can reach higher multiplexing efficiency compared with the existing methods. Based on the proposed method, we suggest a scheme to multiplex the BeiDou regional signals and global signals at the B2 frequency. The simulation results of correlation functions and Power Spectrum Density (PSD) verify the correctness and effectiveness of the proposed design method.

Phase-aligned Dual-frequency Constant Envelope Multiplexing Technique for GNSS Signals

2018 ◽  
Vol 71 (4) ◽  
pp. 899-918
Author(s):  
Zhihui Zhou ◽  
Zuping Tang ◽  
Jiaolong Wei ◽  
Xuan Xia ◽  
Tao Yan
Keyword(s):  
Phase Relationship ◽  
Global Navigation Satellite Systems ◽  
Lookup Table ◽  
Signal Design ◽  
Dual Frequency ◽  
Binary Offset Carrier ◽  
Signal Model ◽  
Frequency Signal ◽  
Satellite Systems ◽  
Constant Envelope

In the new generation of Global Navigation Satellite Systems (GNSS), dual-frequency constant envelope multiplexing is widely desired and is becoming an important subject in signal design. Considerable work has been devoted to multiplexing for the Alternative Binary Offset Carrier (AltBOC)-like signal model, for which each sideband consists of two or fewer signal components. In this paper, a phase-aligned dual-frequency constant envelope multiplexing technique is proposed for a general dual-frequency signal model. This multiplexing technique can be used to combine two constant-envelope-modulated signals in two sidebands into a composite signal with a constant envelope, where the constant-envelope-modulated signal in each sideband consists of an arbitrary number of signal components with an arbitrary power ratio and phase relationship among the signal components. A Lookup Table (LUT)-based signal generation method is also proposed, for which the required driving clock rate of the signal generator can be flexibly adjusted to meet the requirements of the satellite payload. Applications for the AltBOC-like signal model and a general dual-frequency signal model in the Beidou B1 band validate the flexibility and high multiplexing efficiency of our method. Specifically, AltBOC is a special case of the proposed method.

scholarly journals Multiplexing modulation design optimization and quality evaluation of BDS-3 PPP service signal

2022 ◽  
Vol 3 (1) ◽  
Author(s):  
Cheng Liu ◽  
Zheng Yao ◽  
Dun Wang ◽  
Weiguang Gao ◽  
Tianxiong Liu ◽  
...  
Keyword(s):  
Average Length ◽  
Large Diameter ◽  
Satellite System ◽  
Transmission Efficiency ◽  
Actual State ◽  
Signal Design ◽  
Binary Offset Carrier ◽  
Modulation Technique ◽  
Constant Envelope ◽  
S Curve

AbstractThe Precise Point Positioning (PPP) service of BeiDou-3 Navigation Satellite System (BDS-3) is implemented on its Geostationary Earth Orbit (GEO) satellites. However, its signal design is limited by the actual power of satellite and other conditions. Furthermore, the design needs to fully consider the compatibility of different service phases. Starting from the actual state of the BDS-3 GEO satellite, this paper studies the multiplexing modulation of the BDS PPP service signal that is based on the Asymmetric Constant Envelope Binary Offset Carrier (ACE-BOC) technique and proposes several feasible schemes for this signal. Comparison and optimization of these techniques are made from the aspects of transmission efficiency, multiplexing efficiency, and service forward compatibility. Based on the Type-III ACE-BOC multiplexing modulation technique, phase rotation and intermodulation reconstruction techniques are proposed to suppress the intermodulation interference issue. Finally, a signal based on improved ACE-BOC multiplexing is designed. The quality of the proposed signal was continuously monitored and tested using large-diameter antennas. The evaluation results show that the power spectrum deviation of the signal is 0.228 dB, the correlation loss is 0.110 dB, the S-curve slope deviation is 1.558% on average, the average length difference between the positive/negative chip and the ideal chip is only 0.0006 ns, and the coherence between the carrier and the pseudo code is 0.082°. All quality indicators are satisfactory, indicating that the proposed signal multiplexing modulation technique is an ideal solution that meets all the requirements of the design constraints, and can achieve efficient information broadcasting and forward compatibility of the BDS PPP service.

scholarly journals Galileo E5 AltBOC Signals: Application for Single-Frequency Total Electron Content Estimations

2021 ◽  
Vol 13 (19) ◽  
pp. 3973
Author(s):  
Artem M. Padokhin ◽  
Anna A. Mylnikova ◽  
Yury V. Yasyukevich ◽  
Yury V. Morozov ◽  
Gregory A. Kurbatov ◽  
...  
Keyword(s):  
Total Electron Content ◽  
Noise Level ◽  
Satellite System ◽  
Single Frequency ◽  
Electron Content ◽  
Dual Frequency ◽  
Binary Offset Carrier ◽  
Total Electron ◽  
Galileo E5 ◽  
Global Navigation Satellite

Global navigation satellite system signals are known to be an efficient tool to monitor the Earth ionosphere. We suggest Galileo E5 AltBOC phase and pseudorange observables— a single-frequency combination—to estimate the ionospheric total electron content (TEC). We performed a one-month campaign in September 2020 to compare the noise level for different TEC estimations based on single-frequency and dual-frequency data. Unlike GPS, GLONASS, or Galileo E5a and E5b single-frequency TEC estimations (involving signals with binary and quadrature phase-shift keying, such as BPSK and QPSK, or binary offset carrier (BOC) modulation), an extra wideband Galileo E5 AltBOC signal provided the smallest noise level, comparable to that of dual-frequency GPS. For elevation higher than 60 degrees, the 100-sec root-mean-square (RMS) of TEC, an estimated TEC noise proxy, was as follows for different signals: ~0.05 TECU for Galileo E5 AltBOC, 0.09 TECU for GPS L5, ~0.1TECU for Galileo E5a/E5b BPSK, and 0.85 TECU for Galileo E1 CBOC. Dual-frequency phase combinations provided RMS values of 0.03 TECU for Galileo E1/E5, 0.03 and 0.07 TECU for GPS L1/L2 and L1/L5. At low elevations, E5 AltBOC provided at least twice less single-frequency TEC noise as compared with data obtained from E5a or E5b. The short dataset of our study could limit the obtained estimates; however, we expect that the AltBOC single-frequency TEC will still surpass the BPSK analogue in noise parameters when the solar cycle evolves and geomagnetic activity increases. Therefore, AltBOC signals could advance geoscience.

scholarly journals Assessing the quality of ionospheric models through GNSS positioning error: methodology and results

GPS Solutions ◽  
2019 ◽  
Vol 24 (1) ◽  
Author(s):  
Adrià Rovira-Garcia ◽  
Deimos Ibáñez-Segura ◽  
Raul Orús-Perez ◽  
José Miguel Juan ◽  
Jaume Sanz ◽  
...  
Keyword(s):  
Satellite System ◽  
Ionospheric Delay ◽  
Single Frequency ◽  
Positioning Error ◽  
Dual Frequency ◽  
Error Sources ◽  
Ionospheric Models ◽  
Evaluation Metric ◽  
Global Navigation Satellite

Abstract Single-frequency users of the global navigation satellite system (GNSS) must correct for the ionospheric delay. These corrections are available from global ionospheric models (GIMs). Therefore, the accuracy of the GIM is important because the unmodeled or incorrectly part of ionospheric delay contributes to the positioning error of GNSS-based positioning. However, the positioning error of receivers located at known coordinates can be used to infer the accuracy of GIMs in a simple manner. This is why assessment of GIMs by means of the position domain is often used as an alternative to assessments in the ionospheric delay domain. The latter method requires accurate reference ionospheric values obtained from a network solution and complex geodetic modeling. However, evaluations using the positioning error method present several difficulties, as evidenced in recent works, that can lead to inconsistent results compared to the tests using the ionospheric delay domain. We analyze the reasons why such inconsistencies occur, applying both methodologies. We have computed the position of 34 permanent stations for the entire year of 2014 within the last Solar Maximum. The positioning tests have been done using code pseudoranges and carrier-phase leveled (CCL) measurements. We identify the error sources that make it difficult to distinguish the part of the positioning error that is attributable to the ionospheric correction: the measurement noise, pseudorange multipath, evaluation metric, and outliers. Once these error sources are considered, we obtain equivalent results to those found in the ionospheric delay domain assessments. Accurate GIMs can provide single-frequency navigation positioning at the decimeter level using CCL measurements and better positions than those obtained using the dual-frequency ionospheric-free combination of pseudoranges. Finally, some recommendations are provided for further studies of ionospheric models using the position domain method.

scholarly journals Kinematic PPP Using Mixed GPS/Glonass Single-Frequency Observations

2019 ◽  
Vol 54 (3) ◽  
pp. 97-112
Author(s):  
Mostafa Hamed ◽  
Ashraf Abdallah ◽  
Ashraf Farah
Keyword(s):  
Low Cost ◽  
Satellite System ◽  
Single Frequency ◽  
Future Research ◽  
Frequency Data ◽  
Dual Frequency ◽  
Trajectory Data ◽  
Average Improvement ◽  
Kinematic Ppp ◽  
Global Navigation Satellite

Abstract Nowadays, Precise Point Positioning (PPP) is a very popular technique for Global Navigation Satellite System (GNSS) positioning. The advantage of PPP is its low cost as well as no distance limitation when compared with the differential technique. Single-frequency receivers have the advantage of cost effectiveness when compared with the expensive dual-frequency receivers, but the ionosphere error makes a difficulty to be completely mitigated. This research aims to assess the effect of using observations from both GPS and GLONASS constellations in comparison with GPS only for kinematic purposes using single-frequency observations. Six days of the year 2018 with single-frequency data for the Ethiopian IGS station named “ADIS” were processed epoch by epoch for 24 hours once with GPS-only observations and another with GPS/GLONASS observations. In addition to “ADIS” station, a kinematic track in the New Aswan City, Aswan, Egypt, has been observed using Leica GS15, geodetic type, dual-frequency, GPS/GLONASS GNSS receiver and single-frequency data have been processed. Net_Diff software was used for processing all the data. The results have been compared with a reference solution. Adding GLONASS satellites significantly improved the satellite number and Position Dilution Of Precision (PDOP) value and accordingly improved the accuracy of positioning. In the case of “ADIS” data, the 3D Root Mean Square Error (RMSE) ranged between 0.273 and 0.816 m for GPS only and improved to a range from 0.256 to 0.550 m for GPS/GLONASS for the 6 processed days. An average improvement ratio of 24%, 29%, 30%, and 29% in the east, north, height, and 3D position components, respectively, was achieved. For the kinematic trajectory, the 3D position RMSE improved from 0.733 m for GPS only to 0.638 m for GPS/GLONASS. The improvement ratios were 7%, 5%, 28%, and 13% in the east, north, height, and 3D position components, respectively, for the kinematic trajectory data. This opens the way to add observations from the other two constellations (Galileo and BeiDou) for more accuracy in future research.

scholarly journals Comparison of Multi-GNSS Time and Frequency Transfer Performance Using Overlap-Frequency Observations

2021 ◽  
Vol 13 (16) ◽  
pp. 3130
Author(s):  
Pengfei Zhang ◽  
Rui Tu ◽  
Yuping Gao ◽  
Ju Hong ◽  
Junqiang Han ◽  
...  
Keyword(s):  
Carrier Phase ◽  
Satellite System ◽  
Single Frequency ◽  
Navigation Satellite ◽  
Transfer Performance ◽  
Dual Frequency ◽  
Time Transfer ◽  
Difference Series ◽  
Frequency Transfer ◽  
Global Navigation Satellite

The modernized GPS, Galileo, and BeiDou global navigation satellite system (BDS3) offers new potential for time transfer using overlap-frequency (L1/E1/B1, L5/E5a/B2a) observations. To assess the performance of time and frequency transfer with overlap-frequency observations for GPS, Galileo, and BDS3, the mathematical models of single- and dual-frequency using the carrier-phase (CP) technique are discussed and presented. For the single-frequency CP model, the three-day average RMS values of the L5/E5a/B2a clock difference series were 0.218 ns for Galileo and 0.263 ns for BDS3, of which the improvements were 36.2% for Galileo and 43.9% for BDS3 when compared with the L1/E1/B1 solution at BRUX–PTBB. For the hydrogen–cesium time link BRUX–KIRU, the RMS values of the L5/E5a/B2a solution were 0.490 ns for Galileo and 0.608 ns for BDS3, improving Galileo by 6.4% and BDS3 by 12.5% when compared with the L1/E1/B1 solution. For the dual-frequency CP model, the average stability values of the L5/E5a/B2a solution at the BRUX–PTBB time link were 3.54∙× 10−12 for GPS, 2.20 × 10−12 for Galileo, and 2.69 × 10−12 for BDS3, of which the improvements were 21.0%, 45.1%, and 52.3%, respectively, when compared with the L1/E1/B1 solution. For the BRUX–KIRU time link, the improvements were 4.2%, 30.5%, and 36.1%, respectively.

Signal Structure and Simulation of Compass Satellite Navigation System

2013 ◽  
Vol 390 ◽  
pp. 485-489
Author(s):  
Z. Huang ◽  
H. Yuan
Keyword(s):  
Navigation System ◽  
Satellite Navigation ◽  
Satellite System ◽  
Signal Design ◽  
Characteristic Analysis ◽  
Binary Offset Carrier ◽  
Satellite Navigation System ◽  
Signal Structure ◽  
Power Spectral ◽  
Compass System

Due to Chinas compass satellite navigation system which is under development, signals will be designed to obey some constraints and cooperate with other satellite system. Binary offset carrier BOC characterizing good correlation, band sharing and spectral separability is proposed for Compass system. Signal structure and development of Compass system is first analyzed in this paper, and then the principles of several BOC modulations are elaborated. The emphasis is put on a characteristic analysis of power spectral density and autocorrelation function. Further, the frequency spectrum of AltBOC modulation is simulated with Matlab due to B2 signal structure. The simulation results will be instructive meaning for compass phase Ш signal design and engineer implementation.

scholarly journals Ionosphere-Constrained Single-Frequency PPP with an Android Smartphone and Assessment of GNSS Observations

Sensors ◽  
2020 ◽  
Vol 20 (20) ◽  
pp. 5917
Author(s):  
Guangxing Wang ◽  
Yadong Bo ◽  
Qiang Yu ◽  
Min Li ◽  
Zhihao Yin ◽  
...  
Keyword(s):  
Single Point ◽  
Application Programming Interface ◽  
Satellite System ◽  
Single Frequency ◽  
Dual Frequency ◽  
Application Programming ◽  
Point Positioning ◽  
Global Navigation Satellite ◽  
Gnss Observations ◽  
Better Than

With the development of Global Navigation Satellite System (GNSS) and the opening of Application Programming Interface (API) of Android terminals, the positioning research of Android terminals has attracted the attention of GNSS community. In this paper, three static experiments were conducted to analyze the raw GNSS observations quality and positioning performances of the smartphones. For the two experimental smartphones, the numbers of visible satellites with dual-frequency signals are unstable and not enough for dual-frequency Precise Point Positioning (PPP) processing all through the day. Therefore, the ionosphere-constrained single-frequency PPP model was employed to improve the positioning with the smartphones, and its performance was evaluated and compared with those of the Single Point Positioning (SPP) and the traditional PPP models. The results show that horizontal positioning accuracies of the smartphones with the improved PPP model are better than 1 m, while those with the SPP and the traditional PPP models are about 2 m.

scholarly journals Deep learning of total electron content

2021 ◽  
Vol 3 (7) ◽  
Author(s):  
Omid Memarian Sorkhabi
Keyword(s):  
Deep Learning ◽  
Total Electron Content ◽  
Single Layer ◽  
Activation Function ◽  
Satellite System ◽  
Single Frequency ◽  
Electron Content ◽  
Dual Frequency ◽  
Total Electron ◽  
Global Navigation Satellite

AbstractOne of the most notable errors in the global navigation satellite system (GNSS) is the ionospheric delay due to the total electron content (TEC). TEC is the number of electrons in the ionosphere in the signal path from the satellite to the receiver, which fluctuates with time and location. This error is one of the major problems in single-frequency (SF) GPS receivers. One way to eliminate this error is to use dual-frequency. Users of SF receivers should either use estimation models or local models to reduce this error. In this study, deep learning of artificial neural networks (ANN) was used to estimate TEC for SF users. For this purpose, the ionosphere as a single-layer model (assuming that all free electrons in the ionosphere are in this thin layer) is locally modeled by the code observation method. Linear combination has been used by selecting 24 permanent GNSS stations in the northwest of Iran. TEC was modeled independently of the geometry between the satellite and the receiver, called L4. This modeling was used to train the error ANN with two 5-day periods of high and low solar and geomagnetic activity range with a hyperbolic tangential sigmoid activation function. The results show that the proposed method is capable of eliminating ionosphere error with an average accuracy of 90%. The international reference ionosphere 2016 (IRI2016) is used for the verification, which has a 96% significance correlation with estimated TEC.

scholarly journals Is GNSS real-time positioning a reliable option to validate erosion studies at olive grove environments?

2020 ◽  
Vol 18 (2) ◽  
pp. e0204
Author(s):  
María S. Garrido-Carretero ◽  
María I. Ramos-Galán ◽  
María C. De Lacy-Pérez de los Cobos ◽  
Sergio Blanca-Mena ◽  
Antonio J. Gil-Cruz
Keyword(s):  
Low Cost ◽  
Satellite System ◽  
Single Frequency ◽  
Olive Grove ◽  
Dual Frequency ◽  
Significance Level ◽  
Digital Elevation ◽  
Significant Difference ◽  
Spatial Redistribution ◽  
Global Navigation Satellite

Aim of study: Soil degradation in agricultural areas is a widespread problem. In this framework, a data validation methodology is presented, including a study of the spatial resolution of Global Navigation Satellite System (GNSS) measurements, the calculation of erosion/deposition models, and the contribution of dual frequency and low-cost single frequency GNSS receivers.Area of study: A test olive grove in SE Spain.Material and methods: The study is based on three observation campaigns, between 2016 and 2018, using different GNSS receivers and working modes. The comparison between different surveys provide the volumetric variation over the analyzed period.Main results: Considering the dual-frequency receiver, there was no statistically significant difference between the means and the variances from 1.5 m and from 4.5 m data resolution at the 0.05 significance level. In order to estimate vertical differences from successive GNSS campaigns a differential digital elevation approach was applied. Although the differences depended on the zone of the test area and they changed along the monitoring period, the erosion rate could be catalogued as very low. The dual-frequency receiver satisfied the vertical centimetric precision limits for high accurate Digital Elevation Model (DEM), making it a reliable and accurate option to validate erosion studies in small areas.Research highlights: The results have allowed the characterization of multi-annual spatial redistribution of the topsoil at local scale, being of great help to design future prevention actions for the “tillage erosion” in olive grove environments. However, more tests are needed to guarantee the feasibility of low-cost receivers.

Sign in / Sign up

Export Citation Format

Share Document