A New Pre-Embedding Immunogold Method That Permits to Obtain a Very High Signal with a Very Good Ultrastucture

2001 ◽  
Vol 7 (S2) ◽  
pp. 1044-1045
Author(s):  
G. Grondin ◽  
A.R. Bcaudoin
Keyword(s):  
New Technologies ◽  
Immunofluorescence Microscopy ◽  
High Signal ◽  
Sodium Metaperiodate ◽  
Two Photon ◽  
Cacodylate Buffer ◽  
Ultrastructure Preservation ◽  
High Level ◽  
Very High

The ultimate goal of the immunocytochemistry is to get the best signal with the lowest background while preserving ultrastructure. Unfortunaly too often the experimentator faces a compromise between density of the signal and ultrastructure preservation (1). with the advent of hight resolution confocal light microscopy, two photon imaging and other new technologies there is a need to provide the best immunocytochemical complementary results with the high resolution of the electron microscope. But often for exemple the high level of labelling observed by immunofluorescence microscopy is not matched by immunocytochemistry (2). One approach to obtain comparable levels of labelling is to use comparable protocols. We propose here such a new immunogold method. to illustrate our point we used a very convenient biological material, the adherent cells grown on 35 mm plastic culture dishes. The following procedure was applied : Confluent endothelial cells were fixed in situ for 3 hours with the following freshly prepared and filtered solution : 1 % 1-lysine, 4% paraformaldehyde, 0.04% glutaraldehyde, 0.25% sodium metaperiodate in 0.04M sodium cacodylate buffer, pH 7.4.

Investigation of the chemical origin and evidential value of differences in the SERS spectra of blue gel inks

The Analyst ◽  
2016 ◽  
Vol 141 (17) ◽  
pp. 5152-5158 ◽  
Author(s):  
Yen Cheng Ho ◽  
Wendy W. Y. Lee ◽  
Steven E. J. Bell
Keyword(s):  
Polymer Films ◽  
Resonance Raman ◽  
High Signal ◽  
Ag Nanoparticle ◽  
Signal Noise ◽  
Evidential Value ◽  
Surface Enhanced ◽  
Nanoparticle Aggregates ◽  
Very High

Highly swellable polymer films doped with Ag nanoparticle aggregates (poly-SERS films) have been used to record very high signal : noise ratio, reproducible surface-enhanced resonance Raman (SERRS) spectra of in situ dried ink lines and their constituent dyes using both 633 and 785 nm excitation.

Two-photon excitation microscopy in cellular biophysics

1995 ◽  
Vol 53 ◽  
pp. 62-63
Author(s):  
David W. Piston ◽  
Brian D. Bennett ◽  
Robert G. Summers
Keyword(s):  
Confocal Microscopy ◽  
Laser Beam ◽  
Duty Cycle ◽  
Excited Electronic State ◽  
Input Power ◽  
Two Photon ◽  
Simultaneous Absorption ◽  
Photon Excitation ◽  
Very High ◽  
Two Photon Excitation

Two-photon excitation microscopy (TPEM) provides attractive advantages over confocal microscopy for three-dimensionally resolved fluorescence imaging and photochemistry. Two-photon excitation arises from the simultaneous absorption of two photons in a single quantitized event whose probability is proportional to the square of the instantaneous intensity. For example, two red photons can cause the transition to an excited electronic state normally reached by absorption in the ultraviolet. In practice, two-photon excitation is made possible by the very high local instantaneous intensity provided by a combination of diffraction-limited focusing of a single laser beam in the microscope and the temporal concentration of 100 femtosecond pulses generated by a mode-locked laser. Resultant peak excitation intensities are 106 times greater than the CW intensities used in confocal microscopy, but the pulse duty cycle of 10-5 maintains the average input power on the order of 10 mW, only slightly greater than the power normally used in confocal microscopy.

Two-photon excitation fluorescence microscopy in living systems

1993 ◽  
Vol 51 ◽  
pp. 154-155 ◽  
Author(s):  
David W. Piston
Keyword(s):  
Confocal Microscopy ◽  
Fluorescence Microscopy ◽  
Singlet State ◽  
Excited Electronic State ◽  
Input Power ◽  
Two Photon ◽  
Simultaneous Absorption ◽  
Photon Excitation ◽  
Very High ◽  
Two Photon Excitation

Two-photon excitation fluorescence microscopy provides attractive advantages over confocal microscopy for three-dimensionally resolved fluorescence imaging. Two-photon excitation arises from the simultaneous absorption of two photons in a single quantitized event whose probability is proportional to the square of the instantaneous intensity. For example, two red photons can cause the transition to an excited electronic state normally reached by absorption in the ultraviolet. In our fluorescence experiments, the final excited state is the same singlet state that is populated during a conventional fluorescence experiment. Thus, the fluorophore exhibits the same emission properties (e.g. wavelength shifts, environmental sensitivity) used in typical biological microscopy studies. In practice, two-photon excitation is made possible by the very high local instantaneous intensity provided by a combination of diffraction-limited focusing of a single laser beam in the microscope and the temporal concentration of 100 femtosecond pulses generated by a mode-locked laser. Resultant peak excitation intensities are 106 times greater than the CW intensities used in confocal microscopy, but the pulse duty cycle of 10−5 maintains the average input power on the order of 10 mW, only slightly greater than the power normally used in confocal microscopy.

New Technologies for Decontamination of Radioactive Substances Scattered by Nuclear Accident / Nowe Technologie Dekontaminacji Radioaktywnych Substancji Rozproszonych Przez Awarie Nuklearna

2013 ◽  
Vol 58 (1) ◽  
pp. 283-290 ◽  
Author(s):  
Y. Nishizaki ◽  
H. Miyamae ◽  
S. Ichikawa ◽  
K. Izumiya ◽  
T. Takano ◽  
...  
Keyword(s):  
Radioactive Waste ◽  
New Technologies ◽  
Ferric Hydroxide ◽  
Nuclear Accident ◽  
Radioactive Cesium ◽  
Cesium Ions ◽  
Naoh Solution ◽  
High Concentrations ◽  
Water Rinsing

Our effort for decontamination of radioactive cesium scattered widely by nuclear accident in March 2011 in Fukushima, Japan has been described. Radioactive cesium scattered widely in Japan has been accumulating in arc or plasma molten-solidified ash in waste incinerating facilities up to 90,000 Bq/kg of the radioactive waste. Water rinsing of the ash resulted in dissolution of cesium ions together with high concentrations of potassium and sodium ions. Although potassium inhibits the adsorption of cesium on zeolite, we succeeded to precipitate cesium by in-situ formation of ferric ferrocyanide and iron rust in the radioactive filtrate after rinsing of the radioactive ash with water. Because the regulation of no preservation of any kind of cyanide substances, cesium was separated from the precipitate consisting of cesium-captured ferric ferrocyanide and ferric hydroxide in diluted NaOH solution and subsequent filtration gave rise to the potassium-free radioactive filtrate. Cesium was captured by zeolite from the potassium-free radioactive filtrate. The amount of this final radioactive waste of zeolite was significantly lower than that of the arc-molten-solidified ash.

In-situ automatic observations of ice thickness of seas

2012 ◽  
Vol 19 (3) ◽  
pp. 583-592 ◽  
Author(s):  
Yinke Dou ◽  
Xiaomin Chang
Keyword(s):  
Sea Ice ◽  
New Technologies ◽  
Capacitive Sensor ◽  
Automatic Monitoring ◽  
Ice Thickness ◽  
In Situ Observation ◽  
Glacier Surface ◽  
Sea Ice Thickness ◽  
Surface Ice

Abstract Ice thickness is one of the most critical physical indicators in the ice science and engineering. It is therefore very necessary to develop in-situ automatic observation technologies of ice thickness. This paper proposes the principle of three new technologies of in-situ automatic observations of sea ice thickness and provides the findings of laboratory applications. The results show that the in-situ observation accuracy of the monitor apparatus based on the Magnetostrictive Delay Line (MDL) principle can reach ±2 mm, which has solved the “bottleneck” problem of restricting the fine development of a sea ice thermodynamic model, and the resistance accuracy of monitor apparatus with temperature gradient can reach the centimeter level and research the ice and snow substance balance by automatically measuring the glacier surface ice and snow change. The measurement accuracy of the capacitive sensor for ice thickness can also reach ±4 mm and the capacitive sensor is of the potential for automatic monitoring the water level under the ice and the ice formation and development process in water. Such three new technologies can meet different needs of fixed-point ice thickness observation and realize the simultaneous measurement in order to accurately judge the ice thickness.

Site specific agricultural soil management with the use of new technologies

2013 ◽  
Vol 16 (1) ◽  
pp. 59-67
Keyword(s):  
New Technologies ◽  
Digital Interface ◽  
Appropriate Treatment ◽  
Wide Range ◽  
Soil Variation ◽  
Soil Information ◽  
Remote Sensing Techniques ◽  
Agricultural Areas

<p>The Soil Science Institute of Thessaloniki produces new digitized Soil Maps that provide a useful electronic database for the spatial representation of the soil variation within a region, based on in situ soil sampling, laboratory analyses, GIS techniques and plant nutrition mathematical models, coupled with the local land cadastre. The novelty of these studies is that local agronomists have immediate access to a wide range of soil information by clicking on a field parcel shown in this digital interface and, therefore, can suggest an appropriate treatment (e.g. liming, manure incorporation, desalination, application of proper type and quantity of fertilizer) depending on the field conditions and cultivated crops. A specific case study is presented in the current work with regards to the construction of the digitized Soil Map of the regional unit of Kastoria. The potential of this map can easily be realized by the fact that the mapping of the physicochemical properties of the soils in this region provided delineation zones for differential fertilization management. An experiment was also conducted using remote sensing techniques for the enhancement of the fertilization advisory software database, which is a component of the digitized map, and the optimization of nitrogen management in agricultural areas.</p>

التغير المناخي واثره في المقنن المائي لمحصول العنب في محافظة ديالى

2019 ◽  
Vol 1 (34) ◽  
pp. 391-422
Author(s):  
اشواق حسن حميد صالح
Keyword(s):  
Climate Change ◽  
Statistical Analysis ◽  
Wind Speed ◽  
Extreme Temperature ◽  
Solar Brightness ◽  
The Subject ◽  
Climate Station ◽  
The Times ◽  
High Level ◽  
Very High

Climate change and its impact on water resources is the problem of the times. Therefore, this study is concerned with the subject of climate change and its impact on the water ration of the grape harvest in Diyala Governorate. The study was based on the data of the Khanaqin climate station for the period 1973-2017, (1986-2017) due to lack of data at governorate level. The general trend of the elements of the climate and its effect on the water formula was extracted. The equation of change was extracted for the duration of the study. The statistical analysis was also used between the elements of the climate (actual brightness, normal temperature, micro and maximum degrees Celsius, wind speed m / s, relative humidity% The results of the statistical analysis confirm that the water ration for the study area is based mainly on the X7 evaporation / netting variable, which is affected by a set of independent variables X1 Solar Brightness X4 X5 Extreme Temperature Wind Speed ​​3X Minimal Temperature and Very High Level .

Relations between carbon removal rates, biofilm size and density of a novel anaerobic reactor: the inverse turbulent bed

2000 ◽  
Vol 41 (4-5) ◽  
pp. 253-260 ◽  
Author(s):  
P. Buffière ◽  
R. Moletta
Keyword(s):  
Removal Rate ◽  
Removal Rates ◽  
Carbon Removal ◽  
Biofilm Growth ◽  
Loading Rates ◽  
Biomass Activity ◽  
High Turbulence ◽  
The One ◽  
High Level ◽  
Very High

An anaerobic inverse turbulent bed, in which the biogas only ensures fluidisation of floating carrier particles, was investigated for carbon removal kinetics and for biofilm growth and detachment. The range of operation of the reactor was kept within 5 and 30 kgCOD· m−3· d−1, with Hydraulic Retention Times between 0.28 and 1 day. The carbon removal efficiency remained between 70 and 85%. Biofilm size were rather low (between 5 and 30 μm) while biofilm density reached very high values (over 80 kgVS· m−3). The biofilm size and density varied with increasing carbon removal rates with opposite trends; as biofilm size increases, its density decreases. On the one hand, biomass activity within the reactor was kept at a high level, (between 0.23 and 0.75 kgTOC· kgVS· d−1, i.e. between 0.6 and 1.85 kgCOD·kgVS · d−1).This result indicates that high turbulence and shear may favour growth of thin, dense and active biofilms. It is thus an interesting tool for biomass control. On the other hand, volatile solid detachment increases quasi linearly with carbon removal rate and the total amount of solid in the reactor levels off at high OLR. This means that detachment could be a limit of the process at higher organic loading rates.

A Tight Connection Among Wealth, Income, Sustainability, and Accounting in an Ultra-Simplified Setting

2017 ◽  
Author(s):  
Martin L. Weitzman
Keyword(s):  
Economic Theory ◽  
Quantitative Relationship ◽  
Theoretical Relationship ◽  
Level Of Abstraction ◽  
Tight Connection ◽  
Basic Concepts ◽  
High Level ◽  
Very High

In theory, and under some very strong assumptions, there exists a tight quantitative relationship among the following four fundamental economic concepts: (1) ‘wealth’; (2) ‘income’; (3) ‘sustainability’; (4) ‘accounting’. These four basic concepts are placed in quotation marks here because a necessary first step will be to carefully and rigorously define what exactly is meant by each. This chapter reviews what is known about this important fourfold quantitative relationship in an ultra-simplified setting. It identifies some basic applications of this simplified economic theory of wealth and income (and sustainability and accounting). While the contents of this chapter are expressed at a very high level of abstraction and require many restrictive assumptions, the fundamental fourfold relationship it sharply highlights should be useful for conceptualizing, at least in principle, what is ‘wealth’ and what is its theoretical relationship to ‘income’, ‘sustainability’, and ‘accounting’.

Sign in / Sign up

Export Citation Format

Share Document