Numerical Investigation of Methane Number and Wobbe Index Effects in Lean-Burn Natural Gas Spark-Ignition Combustion

2019 ◽  
Vol 33 (5) ◽  
pp. 4564-4574 ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Numerical Investigation ◽  
Spark Ignition ◽  
Lean Burn ◽  
Wobbe Index ◽  
Methane Number

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural Gas Spark Ignition

2018 ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Spark Timing ◽  
Heavy Duty Diesel

Increased utilization of natural-gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduce greenhouse-gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOx, CO, and HC emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing, engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late burn (including double-peak heat release rate) was observed for advanced spark timing. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3 %), moderate rate of pressure rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

scholarly journals Impact of Liquefied Natural Gas Composition Changes on Methane Number as a Fuel Quality Requirement

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5060
Author(s):  
Szymon Kuczyński ◽  
Mariusz Łaciak ◽  
Adam Szurlej ◽  
Tomasz Włodek
Keyword(s):  
Natural Gas ◽  
Liquefied Natural Gas ◽  
Methane Content ◽  
Fuel Quality ◽  
Engine Fuel ◽  
Simultaneous Application ◽  
Limit Value ◽  
Wobbe Index ◽  
The One ◽  
Methane Number

The one of main quality requirements of natural gas as an engine fuel is the methane number (MN). This parameter indicates the fuel’s capability to avoid knocking in the engine. A higher MN value indicates a better natural gas quality for gas engines. Natural gas with higher methane content tends to have higher MN value. This study presents analysis of deviation of liquefied natural gas (LNG) composition and its impact on LNG quality as an engine fuel. The analysis of higher hydrocarbons and nitrogen content impact on LNG parameters was considered for several samples of LNG compositions. Most engine manufacturers want to set a new, lower limit value for methane number at 80. This fact causes significant restrictions on the range of variability in the composition of liquefied natural gas. The goal of this study was to determine the combination of the limit content of individual components in liquefied natural gas to achieve the strict methane number criterion (MN > 80). To fulfill this criterion, the methane content in LNG would have to exceed 93.7%mol, and a significant part of the LNG available on the market does not meet these requirements. The analysis also indicated that the methane number cannot be the only qualitative criterion, as its variability depends strongly on the LNG composition. To determine the applicability of LNG as an engine fuel, the simultaneous application of the methane number and Wobbe index criteria was proposed.

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Heavy Duty Diesel ◽  
Ci Engines

Increased utilization of natural gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduced greenhouse gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOX, CO, and hydrocarbon (HC) emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing (ST), engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late-burn (including double-peak heat release rate) was observed for advanced ST. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3%), moderate rate of pressure-rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

Hydrogen Blended Natural Gas Operation of a Heavy Duty Turbocharged Lean Burn Spark Ignition Engine

2004 ◽  
Author(s):  
S. R. Munshi ◽  
C. Nedelcu ◽  
J. Harris ◽  
T. Edwards ◽  
J. Williams ◽  
...  
Keyword(s):  
Natural Gas ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Heavy Duty ◽  
Lean Burn

Evaluation of a Lean-Burn Natural Gas Engine Operating on Variable Methane Number Fuel

2011 ◽  
Author(s):  
Cory J. Kreutzer ◽  
Daniel B. Olsen ◽  
Robin J. Bremmer
Keyword(s):  
Natural Gas ◽  
High Efficiency ◽  
Engine Performance ◽  
Combustion Stability ◽  
Lean Burn ◽  
Natural Gas Engines ◽  
Spark Timing ◽  
Gas Compression ◽  
Fuel Blending ◽  
Methane Number

Wellhead gas from which pipeline natural gas originates has significant variability in composition due to natural variations in deposits. Gas quality is influenced by relative concentrations of both inert and hydrocarbon species. Gas compression engines utilizing wellhead gas as a fuel source often require significant installation time and adjustment of stock configuration due to fuel compositions that vary with time and location. Lean burn natural gas engines are chosen as wellhead compression engines for high efficiency and low emissions while minimizing the effect of variable gas composition. Ideal engine conditions are maintained by operating within the knock and misfire limits of the engine. Additional data is needed to find engine operational limitations. In this work, experimental data was collected on a Cummins GTA8.3SLB engine operating on variable methane number fuel under closed-loop equivalence ratio control. A fuel blending system was used to vary methane number to simulate wellhead compositions. NOx and CO emissions were found to increase with decreasing methane number while combustion stability remained constant. In addition, the effects of carbon dioxide and nitrogen diluents in the fuel were investigated. When diluents were present in the fuel, engine performance could be maintained by spark timing advance.

An Experimental Study of Cyclic Variations in a Lean Burn Natural Gas Fuelled Spark Ignition Engine

2003 ◽  
Author(s):  
A. Ramesh ◽  
Mohand Tazerout ◽  
Olivier Le Corre
Keyword(s):  
Natural Gas ◽  
Heat Release ◽  
Pressure Rise ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
High Rate ◽  
Lean Burn ◽  
Complete Combustion ◽  
Average Value ◽  
Indicated Mean Effective Pressure

This work deals with the nature of cycle by cycle variations in a single cylinder, lean burn, natural gas fuelled spark ignition engine operated at a constant speed of 1500 rev/min under variable equivalence ratio, fixed throttle conditions. Cycle by cycle variations in important parameters like indicated mean effective pressure (IMEP), peak pressure, rate of pressure rise and heat release characteristics were studied. At the lean misfire limit there was a drastic increase in combustion duration. With mixtures leaner than the lean limit, good cycles generally followed poor cycles. However, the vice versa was not true. Cycles that had a high initial heat release rate lead to more complete combustion. A high rate of pressure rise led to a high IMEP. The IMEP of cycles versus their frequency of occurrence was symmetric about the average value when the combustion was good.

Lessons From the Conversion of a Heavy-Duty Compression Ignition Engine to Natural Gas Spark Ignition Operation

2020 ◽  
Author(s):  
Jinlong Liu ◽  
Christopher Ulishney ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Fuel Injection ◽  
Volume Ratio ◽  
Spark Ignition ◽  
Point Of View ◽  
Injection System ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Lean Burn ◽  
Engine Efficiency

Abstract Partial conversion of the large inventory of compression-ignition engines to natural-gas (NG) spark-ignition lean-burn operation can reduce U.S. dependence on imported petroleum and enhance national energy security. This paper describes some of the observations made during such an engine conversion and proposes some solutions to alleviate some of the potential issues. The engine conversion in this study consisted from replacing the diesel injector with a spark plug and adding a port fuel injection system for NG delivery. The results indicated that the retrofitted engine performed reliably at lean-burn conditions, despite the different combustion characteristics compared to conventional SI engines. However, the squish region will trap an important fuel fraction (∼30%) and experience less-optimal burning conditions, hence a slower burning rate. This affected the engine efficiency and increased the unburned hydrocarbon and carbon monoxide emissions. From a combustion point of view, the operation of such converted engines can be optimized by increasing the bowl-to-squish volume ratio, optimizing the piston shape (e.g., by removing the central protrusion and avoiding 90-degree edges inside the bowl). The original compression ratio may also need to be reduced to avoid knocking. Moreover, direct gas injection and/or intake charging will increase the volumetric efficiency, which will benefit engine efficiency and emissions.

Sign in / Sign up

Export Citation Format

Share Document