Conductivities of Some Molten Chlorides at Elevated Temperatures II. Electrical Conductivity of Molten Chlorides (InCl3, ZrCl4, HfCl4) with Negative Temperature Coefficients

Author(s):  
Alexander B. Salyulev ◽  
Alexei M. Potapov
2020 ◽  
Vol 175 (12) ◽  
Author(s):  
Steffen Klumbach ◽  
Hans Keppler

AbstractSubsurface magmatic–hydrothermal systems are often associated with elevated electrical conductivities in the Earthʼs crust. To facilitate the interpretation of these data and to allow distinguishing between the effects of silicate melts and fluids, the electrical conductivity of aqueous fluids in the system H2O–HCl was measured in an externally heated diamond anvil cell. Data were collected to 700 °C and 1 GPa, for HCl concentrations equivalent to 0.01, 0.1, and 1 mol/l at ambient conditions. The data, therefore, more than double the pressure range of previous measurements and extend them to geologically realistic HCl concentrations. The conductivities $$\sigma$$ σ (in S/m) are well reproduced by a numerical model log $$\sigma$$ σ  = −2.032 + 205.8 T−1 + 0.895 log c + 3.888 log $$\rho$$ ρ  + log$$\Lambda_{0}$$ Λ 0 (T,$$\rho$$ ρ ), where T is the temperature in K, c is the HCl concentration in wt. %, and $$\rho$$ ρ is the density of pure water at the corresponding pressure and temperature conditions. $$\Lambda_{0}$$ Λ 0 (T,$$\rho$$ ρ ) is the limiting molar conductivity (in S cm2 mol−1) at infinite dilution, $$\Lambda_{0}$$ Λ 0 (T,$$\rho$$ ρ ) = 2550.14 − 505.10$$\rho$$ ρ  − 429,437 T−1. A regression fit of more than 800 data points to this model yielded R2 = 0.95. Conductivities increase with pressure and fluid densities due to an enhanced dissociation of HCl. However, at constant pressures, conductivities decrease with temperature because of reduced dissociation. This effect is particularly strong at shallow crustal pressures of 100–200 MPa and can reduce conductivities by two orders of magnitude. We, therefore, suggest that the low conductivities sometimes observed at shallow depths below the volcanic centers in magmatic–hydrothermal systems may simply reflect elevated temperatures. The strong negative temperature effect on fluid conductivities may offer a possibility for the remote sensing of temperature variations in such systems and may allow distinguishing the effects of magma intrusions from changes in hydrothermal circulation. The generally very high conductivities of HCl–NaCl–H2O fluids at deep crustal pressures (500 MPa–1 GPa) imply that electrical conductors in the deep crust, as in the Altiplano magmatic province and elsewhere, may at least partially be due to hydrothermal activity.


2004 ◽  
Vol 833 ◽  
Author(s):  
Liang-Yu Chen ◽  
Gary W. Hunter

AbstractPolycrystalline Al2O3 substrates have been proposed and tested for high temperature micro devices packaging intended for operation at temperatures up to 500°C. The dielectric properties of this material, including dielectric constant and effective volume conductivity, at elevated temperatures are of interest, especially for RF packaging applications. This article reports temperature dependent dielectric properties of polycrystalline 96% Al2O3 substrates from room temperature to 550°C measured by the AC impedance method at 120 Hz, 1 kHz, 10 kHz, 100 kHz, and 1 MHz. We observed negative temperature coefficients of volume electrical conductivity of 96% Al2O3 at 1 k, 10 k, and 100 kHz between room temperature and 50°C. The dielectric constant of the material increases significantly with temperature at frequencies below 10 kHz. The physical mechanisms of these dielectric behaviors of 96% Al2O3 at elevated temperatures are discussed.


In the present paper an account is given of experimental measurements on the electrical conductivity of thin films of mercury prepared by evaporative deposition in a high vacuum according to the technique described in previous papers (Lovell 1936; Appleyard and Lovell 1937). In a brief preliminary note (Appleyard 1937) we have pointed out that the results for mercury are very different from those for the alkali metals, and that in particular a considerable thickness of mercury must be deposited on the pyrex surface before conductivity begins. We have since confirmed and extended these observations, obtained accurate absolute values for the thickness of the films, investigated their stability, and made an extended study of their temperature coefficients after heat treatment. A comparison with the results of previous workers is given later.


1941 ◽  
Vol 25 (2) ◽  
pp. 247-261
Author(s):  
Eric Ponder

The acceleration of saponin hemolysis by benzene, indol, and nonyl alcohol has been investigated as a function of temperature, and it has been found that these accelerators have negative temperature coefficients. This points to their being concentrated at the cell surface, and to the surface being the seat of their accelerating action. It is shown that the accelerating power of indol (used as a typical accelerator) is constant so long as the lysin in the system is capable of producing lysis per se, but that the acceleration falls off when only sublytic concentrations are present. The relations are expressed in a series of equations, and explained in terms of the reactions among the accelerator, the lysin, and the membrane component, which breaks down in spots, rather than uniformly, when lysis occurs. The argument involves a consideration of the idea that a monolayer of lysin at the cell surface is necessary for hemolysis, of Abramson's hypothesis of "key spots" on the surface, of the rate of escape of hemoglobin from the hemolyzing cell, and of the results of electrophoretic and impedance measurements. The existing theory of the kinetics is extended by introducing the idea of a variation in resistance from point to point in the cell membrane; in this form it describes the situation so far as is at present known, and shows that the results of the various methods of investigation are consistent with each other. The only idea discussed which seems to have little foundation is that lysis is determined by the formation of a monolayer of lysin at the cell surface; when this occurs, it must do so only as a special case. Finally, a semi-quantitative description of the frequency distribution of the resistances in the membrane is derived from existing data. The variation in resistance which it is necessary to assume is quite small, as might be expected in the case of a membrane with a regular ultra-structure.


2018 ◽  
Vol 183 ◽  
pp. 02011
Author(s):  
Kenji Nakai ◽  
Tsubasa Fukushima ◽  
Takashi Yokoyama ◽  
Kazuo Arakawa

The high strain-rate compressive characteristics of a cross-ply carbon/epoxy laminated composite in the three principal material directions or fibre (1-), in-plane transverse (2-) and throughthickness (3-) directions are investigated on the conventional split Hopkinson pressure bar (SHPB) over a range of temperatures between 20 and 80 °C. A nearly 10 mm thick cross-ply carbon/epoxy composite laminate fabricated using vacuum assisted resin transfer molding (VaRTM) was tested. Cylindrical specimens with a slenderness ratio (= length/diameter) of 0.5 are used in high strain-rate tests, and those with the slenderness ratios of 1.0 and 1.5 are used in low and intermediate strain-rate tests. The uniaxial compressive stress-strain curves up to failure at quasi-static and intermediate strain rates are measured on an Instron testing machine at elevated temperatures. A pair of steel rings is attached to both ends of the cylindrical specimens to prevent premature end crushing in the 1-and 2-direction tests on the Instron testing machine. It is shown that the ultimate compressive strength (or failure stress) exhibits positive strainrate effects and negative temperature ones over a strain-rate range of 10–3 to 103/s and a temperature range of 20 to 80 °C in the three principal material directions.


Author(s):  
Hector Carreon

Due to elevated temperatures, excessive stresses and severed corrosion conditions, turbine engine components are subject to creep processes that limit the components life such as a turbine bucket. The failure mechanism of a turbine bucket is related primarily to creep and corrosion and secondarily to thermal fatigue. As a result, it is desirable to assess the current condition of such turbine component. This study uses the eddy current (EC) nondestructive evaluation technique in an effort to monitor the creep damage in a nickel base super-alloy, 7FA stage 2 turbine bucket after service. The experimental results show significative electrical conductivity variations in eddy current images on the creep damage zone of nickel base super-alloy samples cut from a turbine bucket. Thermoelectric power (TEP) measurements were also conducted in order to obtain a direct correlation between the presence of material changes due to creep damage and the electrical conductivity measurements.


Sign in / Sign up

Export Citation Format

Share Document