scholarly journals Thermal Analysis of Vertical Plate Fin Heat Sink

2020 ◽  
Vol 170 ◽  
pp. 01022
Author(s):  
Anilkumar Sathe ◽  
Sudarshan Sanap ◽  
Sunil Dingare ◽  
Narayan Sane
Keyword(s):  
Heat Transfer ◽  
Thermal Analysis ◽  
Pressure Drop ◽  
Free Convection ◽  
Experimental Method ◽  
Heat Input ◽  
Heat Sink ◽  
Vertical Plate ◽  
Heat Sinks ◽  
Power Requirement

Heat Sinks are widely used to remove the heat from the components which are generating heat during their functioning. Overheating causes malfunctioning of the components as well as it is responsible for reducing their life. Free convection is very common way of heat transfer from the heat sink considering power requirement, pressure drop and cost of the forced convection. This paper presents the thermal analysis of vertical plate fin heat sink by theoretical and experimental method at variable heat input. The results are obtained by taking experimental observations and are validated with already existing correlations suggested by various researchers in the literature.

Pin-Fin Heat Sink With Horizontal Base and Blocked Edges

2008 ◽  
Author(s):  
D. Sahray ◽  
H. Shmueli ◽  
N. Segal ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Contact Resistance ◽  
Cross Section ◽  
Heat Input ◽  
Heat Sink ◽  
Numerical Study ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Pin Fin

In the present work, horizontal-base pin fin heat sinks exposed to free convection in air are studied. They are made of aluminum, and there is no contact resistance between the base and the fins. For the same base dimensions the fin height and pitch vary. The fins have a constant square cross-section. The edges of the sink are blocked: the surrounding insulation is flush with the fin tips. The effect of fin height and pitch on the performance of the sink is studied experimentally and numerically. In the experiments, the heat sinks are heated using foil electrical heaters. The heat input is set, and temperatures of the base and fins are measured. In the corresponding numerical study, the sinks and their environment are modeled using the Fluent 6 software. The results show that heat transfer enhancement due to the fins is not monotonic. The differences between sparsely and densely populated sinks are analyzed for various fin heights. Also assessed are effects of the blocked edges as compared to the previously studied cases where the sink edges were exposed to the surroundings.

Effect of Fin Pitch and Height on Pin-Fin Heat Sink Performance

2008 ◽  
Author(s):  
D. Sahray ◽  
H. Shmueli ◽  
N. Segal ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Contact Resistance ◽  
Cross Section ◽  
Heat Input ◽  
Heat Sink ◽  
Numerical Study ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Pin Fin

In the present work, horizontal-base pin fin heat sinks exposed to free convection in air are studied. They are made of aluminum, and there is no contact resistance between the base and the fins. The sinks have the same base dimensions whereas the fin height and pitch vary. The fins have a constant square cross-section. The effect of fin height and pitch on the performance of the sink is studied experimentally and numerically. In the experiments, the heat sinks are heated using foil electrical heaters. The heat input is set, and temperatures of the base and fins are measured. In the corresponding numerical study, the sinks and their environment are modeled using the Fluent 6.3 software. The results show that heat transfer enhancement due to the fins is not monotonic. The differences between sparsely and densely populated sinks are analyzed for various fin heights.

Compact Modeling of Fluid Flow and Heat Transfer in Straight Fin Heat Sinks

2004 ◽  
Vol 126 (2) ◽  
pp. 247-255 ◽  
Author(s):  
Duckjong Kim ◽  
Sung Jin Kim
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Fluid Flow ◽  
Pressure Drop ◽  
Heat Sink ◽  
Volume Averaging ◽  
Thermal Design ◽  
Heat Sinks ◽  
Compact Modeling ◽  
Flow And Heat Transfer

In the present work, a compact modeling method based on a volume-averaging technique is presented. Its application to an analysis of fluid flow and heat transfer in straight fin heat sinks is then analyzed. In this study, the straight fin heat sink is modeled as a porous medium through which fluid flows. The volume-averaged momentum and energy equations for developing flow in these heat sinks are obtained using the local volume-averaging method. The permeability and the interstitial heat transfer coefficient required to solve these equations are determined analytically from forced convective flow between infinite parallel plates. To validate the compact model proposed in this paper, three aluminum straight fin heat sinks having a base size of 101.43mm×101.43mm are tested with an inlet velocity ranging from 0.5 m/s to 2 m/s. In the experimental investigation, the heat sink is heated uniformly at the bottom. The resulting pressure drop across the heat sink and the temperature distribution at its bottom are then measured and are compared with those obtained through the porous medium approach. Upon comparison, the porous medium approach is shown to accurately predict the pressure drop and heat transfer characteristics of straight fin heat sinks. In addition, evidence indicates that the entrance effect should be considered in the thermal design of heat sinks when Re Dh/L>∼O10.

Optimization Under Uncertainty of Manifold Microchannel Heat Sinks

2012 ◽  
Author(s):  
Suchismita Sarangi ◽  
Karthik K. Bodla ◽  
Suresh V. Garimella ◽  
Jayathi Y. Murthy
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Heat Sink ◽  
Heat Sinks ◽  
Optimization Under Uncertainty ◽  
Microchannel Heat Sink ◽  
Probabilistic Optimization ◽  
Manifold Microchannel

Conventional microchannel heat sinks provide good heat dissipation capability but are associated with high pressure drop and corresponding pumping power. The use of a manifold system that distributes the flow into the microchannels through multiple, alternating inlet and outlet pairs is investigated here. This manifold arrangement greatly reduces the pressure drop incurred due to the smaller flow paths, while simultaneously increasing the heat transfer coefficient by tripping the thermal boundary layers. A three-dimensional numerical model is developed and validated, to study the effect of various geometric parameters on the performance of the manifold microchannel heat sink. Apart from a deterministic analysis, a probabilistic optimization study is also performed. In the presence of uncertainties in the geometric and operating parameters of the system, this probabilistic optimization approach yields an optimal design that is also robust and reliable. Uncertainty-based optimization also yields auxiliary information regarding local and global sensitivities and helps identify the input parameters to which outputs are most sensitive. This information can be used to design improved experiments targeted at the most sensitive inputs. Optimization under uncertainty also provides a quantitative estimate of the allowable uncertainty in input parameters for an acceptable uncertainty in the relevant output parameters. The optimal geometric design parameters with uncertainties that maximize heat transfer coefficient while minimizing pressure drop for fixed input conditions are identified for a manifold microchannel heat sink. A comparison between the deterministic and probabilistic optimization results is also presented.

Partitioned Heat Sinks for Improved Natural Convection

2020 ◽  
Author(s):  
Todd Salamon ◽  
Roger Kempers ◽  
Brian Lynch ◽  
Kevin Terrell ◽  
Elina Simon
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Convective Heat Transfer ◽  
Antenna Arrays ◽  
Heat Sink ◽  
Massive Mimo ◽  
Vertical Plate ◽  
Numerical Models ◽  
Heat Sinks ◽  
Sensible Heat

Abstract The main drivers contributing to the continued growth of network traffic include video, mobile broadband and machine-to-machine communication (Internet of Things, cloud computing, etc.). Two primary technologies that next-generation (5G) networks are using to increase capacity to meet these future demands are massive MIMO (Multi-Input Multi-Output) antenna arrays and new frequency spectrum. The massive MIMO antenna arrays have significant thermal challenges due to the presence of large arrays of active antenna elements coupled with a reliance on natural convection cooling using vertical plate-finned heat sinks. The geometry of vertical plate-finned heat sinks can be optimized (for example, by choosing the fin pitch and thickness that minimize the thermal resistance of the heat sink to ambient air) and enhanced (for example, by embedding heat pipes within the base to improve heat spreading) to improve convective heat transfer. However, heat transfer performance often suffers as the sensible heat rise of the air flowing through the heat sink can be significant, particularly near the top of the heat sink; this issue can be especially problematic for the relatively large or high-aspect-ratio heat sinks associated with massive MIMO arrays. In this study a vertical plate-finned natural convection heat sink was modified by partitioning the heat sink along its length into distinct sections, where each partitioned section ejects heated air and entrains cooler air. This approach increases overall heat sink effectiveness as the net sensible heat rise of the air in any partitioned section is less than that observed in the unpartitioned heat sink. Experiments were performed using a standard heat sink and equivalent heat sinks partitioned into two and three sections for the cases of ducted and un-ducted natural convection with a uniform heat load applied to the rear of the heat sink. Numerical models were developed which compare well to the experimental results and observed trends. The numerical models also provide additional insight regarding the airflow and thermal performance of the partitioned heat sinks. The combined experimental and numerical results show that for relatively tall natural convection cooled heat sinks, the partitioning approach significantly improves convective heat transfer and overall heat sink effectiveness.

Cryogenic Single-Phase Heat Transfer in a Microscale Pin Fin Heat Sink

2013 ◽  
Author(s):  
Eric D. Truong ◽  
Erfan Rasouli ◽  
Vinod Narayanan
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Sink ◽  
Single Phase ◽  
Flow Direction ◽  
Heat Sinks ◽  
Variable Cross ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients

A combined experimental and computational fluid dynamics study of single-phase liquid nitrogen flow through a microscale pin-fin heat sink is presented. Such cryogenic heat sinks find use in applications such as high performance computing and spacecraft thermal management. A circular pin fin heat sink in diameter 5 cm and 250 micrometers in depth was studied herein. Unique features of the heat sink included its variable cross sectional area in the flow direction, variable pin diameters, as well as a circumferential distribution of fluid into the pin fin region. The stainless steel heat sink was fabricated using chemical etching and diffusion bonding. Experimental results indicate that the heat transfer coefficients were relatively unchanged around 2600 W/m2-K for flow rates ranging from 2–4 g/s while the pressure drop increased monotonically with the flow rate. None of the existing correlations in literature on cross flow over a tube bank or micro pin fin heat sinks were able to predict the experimental pressure drop and heat transfer characteristics. However, three dimensional simulations performed using ANSYS Fluent showed reasonable (∼7 percent difference) agreement in the average heat transfer coefficients between experiments and CFD simulations.

Optimization of Pin-Fin Heat Sinks in Bypass Flow Using Entropy Generation Minimization Method

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
W. A. Khan ◽  
J. R. Culham ◽  
M. M. Yovanovich
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Entropy Generation ◽  
Heat Sink ◽  
Heat Sinks ◽  
Entropy Generation Rate ◽  
Bypass Flow ◽  
Minimization Method ◽  
Pin Fin ◽  
Entropy Generation Minimization

An entropy generation minimization method is applied to study the thermodynamic losses caused by heat transfer and pressure drop for the fluid in a cylindrical pin-fin heat sink and bypass flow regions. A general expression for the entropy generation rate is obtained by considering control volumes around the heat sink and bypass regions. The conservation equations for mass and energy with the entropy balance are applied in both regions. Inside the heat sink, analytical/empirical correlations are used for heat transfer coefficients and friction factors, where the reference velocity used in the Reynolds number and the pressure drop is based on the minimum free area available for the fluid flow. In bypass regions theoretical models, based on laws of conservation of mass, momentum, and energy, are used to predict flow velocity and pressure drop. Both in-line and staggered arrangements are studied and their relative performance is compared to the same thermal and hydraulic conditions. A parametric study is also performed to show the effects of bypass on the overall performance of heat sinks.

scholarly journals Heat Transfer Enhancement of Plate-Fin Heat Sinks with Different Types of Winglet Vortex Generators

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5219
Author(s):  
Jin-Cherng Shyu ◽  
Jhao-Siang Jheng
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Heat Sink ◽  
Heat Sinks ◽  
Vortex Generators ◽  
Airflow Velocity ◽  
Delta Winglet ◽  
The Heat Transfer Coefficient

Because the delta winglet in common-flow-down configuration has been recognized as an excellent type of vortex generators (VGs), this study aims to experimentally and numerically investigate the thermo-hydraulic performance of four different forms of winglet VGs featuring sweptback delta winglets in the channel flow in the range 200 < Re < 1000. Both Nusselt number and friction factor of plate-fin heat sinks having different forms of winglets, including delta winglet pair (DWP), rectangular winglet pair (RWP), swept delta winglet pair (SDWP), and swept trapezoid winglet pair (STWP), were measured in a standard wind tunnel without bypass in this study. Four rows of winglets with in-line arrangement were punched on each 10-mm-long, 0.2-mm-thick copper plate, and a total of 16 pieces of copper plates with spacing of 2 mm were fastened together to achieve the heat sink. The projected area, longitudinal and winglet tip spacing, height and angle of attack of those winglets were fixed. Besides that, three-dimensional numerical simulation was also performed in order to investigate the temperature and fluid flow over the plate-fin. The results showed that the longitudinal, common-flow-down vortices generated by the VGs augmented the heat transfer and pressure drop of the heat sink. At airflow velocity of 5 m/s, the heat transfer coefficient and pressure drop of plain plate-fin heat sink were 50.8 W/m2·K and 18 Pa, respectively, while the heat transfer coefficient and the pressure drop of heat sink having SDWP were 70.4 W/m2·K and 36 Pa, respectively. It was found that SDWP produced the highest thermal enhancement factor (TEF) of 1.28 at Re = 1000, followed by both RWP and STWP of similar TEF in the range 200 < Re < 1000. The TEF of DWP was the lowest and it was rapidly increased with the increase of airflow velocity.

Pressure Drop and Heat Transfer in a Single-Phase Micro-Pin-Fin Heat Sink

2006 ◽  
Author(s):  
Abel M. Siu Ho ◽  
Weilin Qu ◽  
Frank Pfefferkorn
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Heat Sink ◽  
Single Phase ◽  
Fluid Transport ◽  
Heat Sinks ◽  
Inlet Temperature ◽  
Pin Fin

The pressure drop and heat transfer characteristics of a single-phase micro-pin-fin heat sink were investigated experimentally. Fabricated from 110 copper, the heat sink consisted of 1950 staggered micro-pins with 200×200 μm2 cross-section by 670 μm height. Deionized water was employed as the cooling liquid. A coolant inlet temperature of 25°C, and two heat flux levels, q" eff = 50 W/cm2 and q" eff = 100 W/cm2, defined relative to the planform area of the heat sink, were tested. The inlet Reynolds number ranged from 93 to 634 for q" eff = 50 W/cm2, and 127 to 634 for q" eff = 100 W/cm2. The measured pressure drop and temperature distribution were used to evaluate average friction factor and local averaged heat transfer coefficient/Nusselt number. Predictions of the Moores and Joshi friction factor correlation and the Chyu et al. heat transfer correlation that were developed using macro-size pin-fin arrays were compared to micro-pin-fin heat sink data. While the Moores and Joshi correlation provide acceptable predictions, the Chyu et al. correlation overpredicted local Nusselt number data by a fairly large margin. These findings point to the need for further study of single-phase thermal/fluid transport process in micro-pin-fin heat sinks.

Numerical Analysis of Entropy Generation in Array of Pin-Fin Heat Sinks for Some Different Geometries

2010 ◽  
Author(s):  
Reza Kamali ◽  
Bamdad Barari ◽  
Ashkan Abbasian Shirazi
Keyword(s):  
Heat Transfer ◽  
Numerical Analysis ◽  
Pressure Drop ◽  
Cross Section ◽  
Entropy Generation ◽  
Heat Sink ◽  
Control Volume ◽  
Heat Sinks ◽  
Entropy Generation Rate ◽  
Pin Fin

In this study, Numerical analysis has been used to investigate entropy generation for array of pin-fin heat sink. Technique is applied to study the thermodynamic losses caused by heat transfer and pressure drop in pin-fin heat sinks. A general expression for the entropy generation rate is obtained by considering the whole heat sink as a control volume and applying the conservation equations for mass and energy with the entropy balance. Analytical and empirical correlations for heat transfer coefficients and friction factors are used in the numerical modeling. Also effects of heat transfer and pressure drop in entropy generation in control volume over pin-fins have been studied. Numerical analysis has been used for three different models of pin-fin heat sinks. The models are different in cross section area. These cross section areas are circle, horizontal ellipse and vertical ellipse which mentioned in next sections. Reference velocity used in Reynolds number and pressure drop is based on the minimum free area available for the fluid flow. Also for numerical analysis in-line arrangement of fins has been investigated and their relative performance is compared. At the end, the performance of these three models has been compared.

Sign in / Sign up

Export Citation Format

Share Document