scholarly journals Non-linear finite element analysis of reinforced concrete members and punching shear strength of HSC slabs

2018 ◽  
Vol 149 ◽  
pp. 02056
Author(s):  
Kernou Nassim ◽  
Belakhdar Khalil ◽  
Benyamina Abdelrahmane Bekaddour
Keyword(s):  
Finite Element ◽  
Linear Equations ◽  
Three Dimensional ◽  
High Strength ◽  
Element Model ◽  
Punching Shear ◽  
Transverse Load ◽  
Convergence Criterion ◽  
Element Analysis ◽  
Non Linear

A rational three-dimensional nonlinear finite element model (NLFEAS) is used for evaluating the behavior of high strength concrete slabs under monotonic transverse load. The non-linear equations of equilibrium have been solved using the incremental-iterative technique based on the modified Newton-Raphson method. The convergence of the solution was controlled by a load convergence criterion. The validity of the theoretical formulations and the program used was verified, through comparison with results obtained using ANSYS program and with available experimental test results. A parametric study was conducted to investigate the effect of different parameters on the behavior of slabs which was evaluated in terms of loaddeflection characteristics, concrete and steel stresses and strains, and failure mechanisms. Also, punching shear resistance of slabs was numerically evaluated and compared with the prediction specified by some design codes.

scholarly journals Fire resistance of circulat steel tubes infilled with ultra-high strength concrete with external fire protection

2019 ◽  
Vol 39 (1) ◽  
pp. 71-80
Author(s):  
Xiao Lyu ◽  
Erfeng Du ◽  
Ran Li
Keyword(s):  
Finite Element ◽  
High Strength Concrete ◽  
Three Dimensional ◽  
High Strength ◽  
Element Model ◽  
Test Results ◽  
Element Analysis ◽  
Strength Concrete ◽  
Tubular Columns ◽  
Axially Loaded

In this paper, a non-linear three-dimensional finite element model is presented in order to study the behaviour of axially loaded ultra-high strength concrete filled circular hollow tubular columns exposed to fire. Ultra-high strength concrete with compressive strength greater than 180 N/mm2 has been developed for concrete filled tubes for use in high–rise buildings. This paper studies the structural performance of fire protected ultra-high strength concrete filled tubular columns exposed to the standard ISO fire. The aim of this work is to understand and represent the behaviour of axially loaded ultra-high strength concrete filled circular hollow tubular columns in fire situations and to compare calculation results with experiment. The numerical analyses are carried out using a general finite element analysis package ABAQUS and the results are validated against the test results in terms of heat distribution and mechanical behavior. Comparison with the test results showed a reasonable agreement with finite element results in terms of temperature prediction and load displacement behavior during the fire.

scholarly journals Finite Element Analysis on Shear Behavior of High-Strength Bolted Connectors under Inverse Push-Off Loading

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 479
Author(s):  
Wei Wang ◽  
Xie-dong Zhang ◽  
Fa-xing Ding ◽  
Xi-long Zhou
Keyword(s):  
Finite Element ◽  
Concrete Slab ◽  
Concrete Strength ◽  
Three Dimensional ◽  
High Strength ◽  
Element Model ◽  
Composite Beams ◽  
Element Analysis ◽  
Shear Connectors ◽  
Parametric Analyses

High-strength bolted shear connectors (HSBSCs), which can be demounted easily and efficiently during deconstruction, are recommended to replace the conventional steel studs in steel–concrete composite beams (SCCBs) to meet the requirements of sustainable development. The existing investigations on the behavior of HSBSCs mainly focus on the positive moment area of composite beams, in which the concrete slab is in compress condition. In this paper, a three-dimensional finite element model (FEM) was developed to investigate the performance of HSBSCs subjected to inverse push-off loading. Material nonlinearities and the interactions among all components were included in the FEM. The accuracy and reliability of the proposed FEM were initially validated against the available push-off test results. Load-carrying capacity and load–slip response of the HSBSCs under inverse push-off loading were further studied by the verified FEM. A parametric study was carried out to determine the influence of the concrete strength, the diameter and tensile strength of bolt and the clearance between the concrete slab and the bolt as well as the bolt pretension on the shear performance of HSBSCs. Based on the extensive parametric analyses, design recommendations for estimating the shear load at the first slip and load-bearing resistance of HSBSCs were proposed and verified.

scholarly journals PENGARUH MODEL DAN SIFAT MATERIAL PADA ANALISIS METODE ELEMEN HINGGA BALOK TABUNG BAJA BUNDAR DIIISI BETON

2017 ◽  
Vol 19 (2) ◽  
pp. 106-114
Author(s):  
Mahmud Kori Effendi
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
Plastic Hinge ◽  
Three Dimensional ◽  
Element Model ◽  
Experimental Results ◽  
Steel Tubes ◽  
Element Analysis ◽  
Non Linear ◽  
Three Dimensional Finite Element

The composite material concrete filled steel tubes, CFST) begin widely recommended in modern structural projects. This material is made of steel tubes filled with concrete. This CFST structure has better ductility than the conventional structure. The three-dimensional finite element modelby means of MSC Marc Mentat software is done by using non-linear material properties for both the steel and concrete. The non-linear geometry is also considered. The results of the finite element analysis method are then compared with experimental results of circular steel tubes filled with concrete. The results of this analysis for both load-deflection and collapse conditions are quite agree with the experimental results. However, the buckling phenomena cannot be modeled in the analysis of the finite element method. The effect of finite element model, which is half span and a quarter of half span, is investigated. The results of this analysis are similar to the results of full-scale analysis. There is plastic hinge in the middle of the beam span. The influence of the material properties of linear and non-linear geometric properties are also investigated. The the plastic hinge did not occur in the middle of beam span.

Experimental determination and numerical modeling of the stiffness of a fastener

2020 ◽  
Vol 62 (12) ◽  
pp. 1215-1220
Author(s):  
Ahmet Atak
Keyword(s):  
Finite Element ◽  
Numerical Modeling ◽  
Finite Element Model ◽  
Computational Cost ◽  
Three Dimensional ◽  
Sandwich Panels ◽  
High Strength ◽  
Element Model ◽  
Secondary Structures ◽  
Element Analysis

Abstract To reduce the fuel consumption and enhance the flight performance of satellites, it is desirable to employ structural components of low weight, high strength, and high stiffness. Therefore, most primary and secondary structures of satellites are built using sandwich panels. Fasteners, which constitute secondary structures, are normally used as joining parts in different types of inserts such as partially potted, fully potted, and through-thickness inserts. Finite element analysis (FEA) is valuable for predicting the behavior of such primary and secondary structures. However, to obtain more realistic results from such analysis, it is necessary to define suitable fastener stiffness values. To this end, in this study, a method for calculating the fastener stiffness of a fully potted insert for sandwich panels using a finite element model is exemplarily developed and experimentally validated. In addition, a shell modeling is established for various connection types to further save time and reduce the computational cost of the finite element model. Finally, the effects of the fastener stiffness on the numerical analysis results for satellite structural system are evaluated. The two-dimensional (2D) structure modeling method used in this study was found to be as fully sufficient as three-dimensional modeling. In addition to saving time and cost, 2D FEA numerical modeling and prediction could reduce elaborate test costs.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

The Optimum Cage Position and Orientation on the ALIF with Facet Screw Fixation: A Finite Element Analysis and the Taguchi Method

2011 ◽  
Vol 27 (3) ◽  
pp. 309-320 ◽  
Author(s):  
C.-Y. Fan ◽  
C.-K. Chao ◽  
C.-C. Hsu ◽  
K.-H. Chao
Keyword(s):  
Finite Element ◽  
Taguchi Method ◽  
Screw Fixation ◽  
Three Dimensional ◽  
Element Model ◽  
Lateral Position ◽  
Element Analysis ◽  
Control Factors ◽  
Position And Orientation ◽  
Noise Factors

ABSTRACTAnterior Lumbar Interbody Fusion (ALIF) has been widely used to treat internal disc degeneration. However, different cage positions and their orientations may affect the initial stability leading to different fusion results. The purpose of the present study is to investigate the optimum cage position and orientation for aiding an ALIF having a transfacet pedicle screw fixation (TFPS). A three-dimensional finite element model (ALIF with TFPS) has been developed to simulate the stability of the L4/L5 fusion segment under five different loading conditions. The Taguchi method was used to evaluate the optimized placement of the cages. Three control factors and two noise factors were included in the parameter design. The control factors included the anterior-posterior position, the medio-lateral position, and the convergent-divergent angle between the two cages. The compressive preload and the strengths of the cancellous bone were set as noise factors. From the results of the FEA and the Taguchi method, we suggest that the optimal cage positioning has a wide anterior placement, and a diverging angle between the two cages. The results show that the optimum cage position simultaneously contributes to a stronger support of the anterior column and lowers the risk of TFPS loosening.

Finite Element Analysis of the Effect of Surface Hardening Depth in Port Crane Wheel

2011 ◽  
Vol 291-294 ◽  
pp. 3282-3286 ◽  
Author(s):  
Jiang Wei Wu ◽  
Peng Wang
Keyword(s):  
Finite Element ◽  
Surface Hardening ◽  
Three Dimensional ◽  
Element Model ◽  
Contact Stresses ◽  
Numerical Results ◽  
Element Analysis ◽  
Finite Element Software ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In port crane industry, the surface hardening technique is widely used in order to improve the strength of wheel. But the hardening depth is chosen only by according to the experience, and the effect of different hardened depths is not studied theoretically. In this paper, the contact stresses in wheel with different hardening depth have been analyzed by applying three-dimensional finite element model. Based on this model, the ANSYS10.0 finite element software is used. The elastic wheel is used to verify the numerical results with the Hertz’s theory. Three different hardening depths, namely 10mm, 25mm and whole hardened wheel, under three different vertical loads were applied. The effect of hardening depth of a surface hardened wheel is discussed by comparing the contact stresses and contact areas from the numerical results.

Nonlinear Finite Element Analysis of Super-Long Pile and Soil Interaction in Soft Soil

2011 ◽  
Vol 201-203 ◽  
pp. 1601-1605 ◽  
Author(s):  
Shang Ping Chen ◽  
Wen Juan Yao ◽  
Sheng Qing Zhu
Keyword(s):  
Finite Element ◽  
Constitutive Model ◽  
Soft Soil ◽  
Three Dimensional ◽  
Nonlinear Behavior ◽  
Element Model ◽  
Element Analysis ◽  
Friction Resistance ◽  
Tip Resistance ◽  
Side Friction

In this paper, a nonlinear three-dimensional finite element model for super-long pile and soil interaction is established. In this model, contact elements are applied to simulate the nonlinear behavior of interaction of super-long pile and soil. A nonlinear elastic constitutive model for concrete is employed to analyze stress-strain relation of pile shaft under the axial load and the Duncan-Chang’s nonlinear constitutive model is used to reflect nonlinear and inelastic properties of soil. The side friction resistance, axial force, pile-tip resistance, and developing trend of soil plastic deformation are obtained and compared with measured results from static load tests. It is demonstrated that a super-long pile has the properties of degradation of side friction resistance and asynchronous action between side and pile-tip resistance, which is different from piles with a short to medium length.

Sign in / Sign up

Export Citation Format

Share Document