scholarly journals Influence of synthesis parameters of mesocellular silica foams doped by nickel on methane reforming by CO2

2018 ◽  
Vol 171 ◽  
pp. 03002 ◽  
Author(s):  
O. Daoura ◽  
M. Boutros ◽  
O. Daoura ◽  
F. Launay ◽  
P. Massiani ◽  
...  
Keyword(s):  
Textural Properties ◽  
Dry Reforming Of Methane ◽  
Synthesis Methods ◽  
Methane Reforming ◽  
X Ray Diffraction ◽  
Synthesis Parameters ◽  
Transmission Electron ◽  
Temperature Programmed ◽  
Mesocellular Silica Foams ◽  
Catalytic Performances

New catalysts based on Ni(0) dispersed onto mesocellular silica foams (MCF) were prepared for Dry Reforming of Methane (DRM). Different synthesis methods of MCF supports (with and without using NH4F or n-butanol) were tested in order to study the influence of the textural properties of the support on the catalytic performances of the catalysts. In all cases, nickel was incorporated using the double solvents method. The resulting calcined materials were characterized by N2 sorption, X-Ray diffraction (XRD) and transmission electron microscopy. Their reducibility was tested by temperature-programmed reduction (TPR). Interestingly, particularly large specific surfaces, pores diameters and pores volumes were observed when NH4F was added to the synthesis gel (MCF(N) materials). The corresponding Ni-MCF(N) catalysts were shown to be the most attractive among other prepared samples with respect to their performances in DRM.

scholarly journals Ce- and Y-Modified Double-Layered Hydroxides as Catalysts for Dry Reforming of Methane: On the Effect of Yttrium Promotion

Catalysts ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 56 ◽  
Author(s):  
Katarzyna Świrk ◽  
Magnus Rønning ◽  
Monika Motak ◽  
Patricia Beaunier ◽  
Patrick Da Costa ◽  
...  
Keyword(s):  
Textural Properties ◽  
Dry Reforming ◽  
Dry Reforming Of Methane ◽  
Side Reactions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Temperature Programmed ◽  
Nickel Species

Ce- and Y-promoted double-layered hydroxides were synthesized and tested in dry reforming of methane (CH4/CO2 = 1/1). The characterization of the catalysts was performed using X-ray fluorescence (XRF), X-ray diffraction (XRD), N2 sorption, temperature-programmed reduction in H2 (TPR-H2), temperature-programmed desorption of CO2 (TPD-CO2), H2 chemisorption, thermogravimetric analysis coupled by mass spectrometry (TGA/MS), Raman, and high-resolution transmission electron microscopy (HRTEM). The promotion with cerium influences textural properties, improves the Ni dispersion, decreases the number of total basic sites, and increases the reduction temperature of nickel species. After promotion with yttrium, the increase in basicity is not directly correlated with the increasing Y loading on the contrary of Ni dispersion. Dry reforming of methane (DRM) was performed as a function of temperature and in isothermal conditions at 700 °C for 5 h. For catalytic tests, a slight increase of the activity is observed for both Y and Ce doped catalysts. This improvement can of course be explained by Ni dispersion, which was found higher for both Y and Ce promoted catalysts. During DRM, the H2/CO ratio was found below unity, which can be explained by side reactions occurrence. These side reactions are linked with the increase of CO2 conversion and led to carbon deposition. By HRTEM, only multi-walled and helical-shaped carbon nanotubes were identified on Y and Ce promoted catalysts. Finally, from Raman spectroscopy, it was found that on Y and Ce promoted catalysts, the formed C is less graphitic as compared to only Ce-based catalyst.

scholarly journals Effect of pore geometry of mesoporous supports on catalytic performances in methane reforming

2018 ◽  
Vol 171 ◽  
pp. 01003
Author(s):  
Joy Tannous ◽  
Leila Karam ◽  
Marie-Nour Kaydouh ◽  
Henri El Zakhem ◽  
Nissrine El Hassan ◽  
...  
Keyword(s):  
Coke Formation ◽  
Three Dimensional ◽  
Dry Reforming ◽  
Methane Reforming ◽  
X Ray Diffraction ◽  
Methane Dry Reforming ◽  
X Ray ◽  
Spent Catalysts ◽  
Temperature Programmed ◽  
Catalytic Performances

Catalysts prepared using three dimensional SBA-16 silica support (composed of micropores and cage-like mesopores) were tested in the reaction of methane dry reforming, in comparison with 2D hexagonal mesoporous SBA-15 support. The samples were evaluated by N2 sorption and X-Ray diffraction (XRD) for the assessment of their textural and structural properties. The reducibility was characterized by temperature programmed reduction (TPR). The catalytic performances were evaluated in methane dry reforming and spent catalysts (after reaction) were characterized for the evaluation of sintering and coke formation by TPH/MS, XRD and HR-TEM.

scholarly journals The Influence Of NO/O2 On The NOx Storage Properties Over A Pt-Ba-Ce/γ-Al2O3 Catalyst

2019 ◽  
Vol 17 (1) ◽  
pp. 1459-1465
Author(s):  
Xuedong Feng ◽  
Jing Yi ◽  
Peng Luo
Keyword(s):  
Sol Gel ◽  
Chemical Properties ◽  
No Oxidation ◽  
Test Results ◽  
X Ray Diffraction ◽  
Storage Performance ◽  
Transmission Electron ◽  
Temperature Programmed ◽  
Physical And Chemical ◽  
Al2o3 Catalyst

AbstractWith the purpose of studying the influence of NO/O2 on the NOx storage activity, a Pt-Ba-Ce/γ-Al2O3 catalyst was synthesized by an acid-aided sol-gel method. The physical and chemical properties of the catalyst were characterized by X-ray diffraction (XRD) and Transmission Electron Microscope (TEM) methods. The results showed that the composition of the catalyst was well-crystallized and the crystalline size of CeO2 (111) was about 5.7 nm. The mechanism of NO and NO2 storage and NOx temperature programmed desorption (NO-TPD) experiments were investigated to evaluate the NOx storage capacity of the catalyst. Pt-Ba-Ce/γ-Al2O3 catalyst presented the supreme NOx storage performance at 350℃, and the maximum value reached to 668.8 μmol / gcat. Compared with O2-free condition, NO oxidation to NO2 by O2 had a beneficial effect on the storage performance of NOx. NO-TPD test results showed that the NOx species stored on the catalyst surface still kept relatively stable even below 350℃.

NANOSEEDING EFFECT IN ZSM-5 CRYSTALLIZATION PROCESS

NANO ◽  
2013 ◽  
Vol 08 (03) ◽  
pp. 1350027
Author(s):  
YI LU ◽  
NAI-QIAN ZHANG ◽  
QIN TONG ◽  
JIN-KU LIU ◽  
DAN-JING HONG
Keyword(s):  
Crystallization Process ◽  
Nitrogen Adsorption ◽  
Particle Size Effect ◽  
Isomerization Reaction ◽  
Transmission Electron Micrograph ◽  
Electron Micrograph ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Induction System ◽  
Temperature Programmed

ZSM-5 zeolites were hydrothermally synthesized in three different seeding pathways under the direction of tetrapropylammonium bromide (TPABr) template. In order to investigate the seeding effect in ZSM-5 crystallization process, ZSM-5 crystals and pre-fabricated MFI-type nanoseeds were added into the original self-induction system, respectively. The final ZSM-5 zeolites were systematically investigated based on XRD (X-ray diffraction), SEM (scanning electron micrograph), TEM (transmission electron micrograph), nitrogen adsorption characterizations and NH3 -TPD (ammonia-temperature programmed desorption). The self-induction system produced ca. 20 μm ZSM-5 zeolite displaying hexagonally uniform prisms. After the addition of ZSM-5 crystal seeds, the crystal sizes were decreased greatly to ca. 5 μm. When MFI-type nanoseeds were adopted, irregular aggregate particles consisting of 20–50 nm primary particles were rapidly synthesized. The varied hydrothermal crystallization kinetics of the three synthesis system was also explored. Adjusting the seed agents alone, ZSM-5 crystals with diverse structural, morphological, textural and hydrothermal behaviors could be fabricated conveniently. The three ZSM-5 zeolites loaded by 0.05 wt.% Pt were assessed for the xylene isomerization reaction to investigate the particle size effect on the catalytic properties.

scholarly journals CO oxidation over Pt-modified CuO catalysts in the presence of water vapour and SO2

2015 ◽  
Vol 18 (2) ◽  
pp. 187-196
Author(s):  
Tri Nguyen ◽  
Anh Cam Ha ◽  
Loc Cam Luu ◽  
Cuong Tien Hoang ◽  
Thi Thi Yen Trinh ◽  
...  
Keyword(s):  
Co Oxidation ◽  
Water Vapour ◽  
Co Adsorption ◽  
X Ray Diffraction ◽  
Active Centers ◽  
Highly Active ◽  
Transmission Electron ◽  
Physico Chemical ◽  
Adsorption Of Co ◽  
Temperature Programmed

The optimal Pt-modified CuO supported on γ-Al2O3 and γ-Al2O3 + CeO2 catalysts have been prepared. Physico-chemical characteristics of catalysts were investigated and determined by the methods of N2 adsorption (BET), X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), temperature-programmed reduction (TPR), and hydrogen pulse chemisorption (HPC). The characteristics of carbon monoxide (CO) adsorption on catalysts were defined by the method of infrared spectroscopy (IR) in the range of 4000 – 400 cm-1. The effect of the mixture of water vapour and SO2 on the activity of these catalysts for the CO oxidation was assessed. Reactions were conducted at 200oC and 350oC in the absence and presence of the mixture of water vapour (1.1 mol %) and SO2 (0.0625 mol %). Concentrations of O2 and CO in the gas mixture were 9.2 mol % and 0.5 mol %, respectively. The results showed that in the catalysts there exist highly active centers Cu1+ and Pt2+. On the catalysts the adsorption of CO on Cu2+, Pt2+, CeO2, and γ - Al2O3 centres was observed. Addition of CeO2 led to increase the reductivity, CO adsorption but decrease in specific surface area of catalyst. The result PtCu/CeAl catalyst shown higher active, but lower stability compared to PtCu/Al catalyst. The mixture of water vapour and SO2 showed the reversible poisoning toward the Pt-CuO catalysts at a temperature of 350oC, but irreversible at 200oC

scholarly journals Nanosized V-Ce Oxides Supported on TiO2 as a Superior Catalyst for the Selective Catalytic Reduction of NO

Catalysts ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 202
Author(s):  
Long Lu ◽  
Xueman Wang ◽  
Chunhua Hu ◽  
Ying Liu ◽  
Xiongbo Chen ◽  
...  
Keyword(s):  
Low Temperature ◽  
Selective Catalytic Reduction ◽  
Photoelectron Spectroscopy ◽  
Catalytic Reduction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Redox Capacity ◽  
Scr Of No ◽  
Temperature Programmed

Nanosized V-Ce oxides supported on TiO2 (VCT) were prepared and utilized in the low-temperature selective catalytic reduction (SCR) of NO with NH3. Compared with the other V-Ce oxides-based catalysts supported on Al2O3, ZrO2, and ZSM-5, VCT showed the best SCR activity in a low-temperature range. The NOx conversion of 90% could be achieved at 220 °C. Characterizations including X-ray diffraction (XRD), scanning election micrograph (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption with NH3 (NH3-TPD), and temperature-programmed reduction with H2 (H2-TPR) showed that V1.05Ce1/TiO2 exhibited a good dispersion of V2O5, enrichment of surface Ce3+ and chemical-absorbed oxygen, and excellent redox capacity and acidity, which resulted in the best SCR performance at low temperature.

scholarly journals Synthesis, Structure, and Luminescent Properties of Europium-Doped Hydroxyapatite Nanocrystalline Powders

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
Carmen Steluta Ciobanu ◽  
Simona Liliana Iconaru ◽  
Florian Massuyeau ◽  
Liliana Violeta Constantin ◽  
Adrian Costescu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Textural Properties ◽  
Average Crystallite Size ◽  
Luminescent Properties ◽  
Nanocrystalline Powders ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Vibrational Studies ◽  
20 Nm

The luminescent europium-doped hydroxyapatite (Eu:HAp, Ca10−xEux(PO4)6(OH)2) with0≤x≤0.2nanocrystalline powders was synthesized by coprecipitation. The structural, morphological, and textural properties were well characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The vibrational studies were performed by Fourier transform infrared, Raman, and photoluminescence spectroscopies. The X-ray diffraction analysis revealed that hydroxyapatite is the unique crystalline constituent of all the samples, indicating that Eu has been successfully inserted into the HAp lattice. Eu doping inhibits HAp crystallization, leading to a decrease of the average crystallite size from around 20 nm in the undoped sample to around 7 nm in the sample with the highest Eu concentration. Furthermore, the samples show the characteristic5D0→7F0transition observed at 578 nm related to Eu3+ions distributed on Ca2+sites of the apatitic structure.

scholarly journals Development of a Novel Method for the Fabrication of Nanostructured Zr(x)Ni(y) Catalyst to Enhance the Desorption Properties of MgH2

Catalysts ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 849
Author(s):  
Gracia Shokano ◽  
Zahir Dehouche ◽  
Basile Galey ◽  
Georgeta Postole
Keyword(s):  
Hydrogen Desorption ◽  
Milling Process ◽  
Hydrogen Release ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Microscope Analysis ◽  
Novel Method ◽  
Temperature Programmed ◽  
The Impact

The present work involves the development of a novel method for the fabrication of zirconium nickel (Zr(x)Ni(y)) alloy used as a nanocatalyst to improve the hydrogen storage properties of the Mg/MgH2 system. The catalyst was fabricated through the high-pressure reactor and activated under hydrogen prior to being mechanically milled with the MgH2 for 5 h under argon. The microstructure characterisation of the samples was determined via SEM-EDX (scanning electron microscope analysis–energy dispersive X-ray spectroscopy), XRD (X-ray diffraction) and FE-HRTEM (field emission high resolution transmission electron microscopy), and the desorption characteristic of the nanocomposite (10 wt.% Zr(x)Ni(y)–MgH2) was determined via TPD (temperature-programmed desorption). The nanostructured MgH2 powder milled with 10 wt.% of the activated Zr(x)Ni(y) based nanocatalyst resulted in a faster hydrogen release—5.9 H2-wt.% at onset temperature 210 °C/peak temperature 232 °C. The observed significant improvement in the hydrogen desorption properties was likely to be the result of the impact of the highly dispersed catalyst on the surface of the Mg/MgH2 system, the reduction in particle size during the ball milling process and/or the formation of Mg0.996Zr0.004 phase during the milling process.

CO Oxidation over Pd Catalysts Supported on Different Supports: A Consideration of Oxygen Storage Capacity of Catalyst

2011 ◽  
Vol 347-353 ◽  
pp. 3298-3301
Author(s):  
Ye Xu ◽  
Jin Qiang Ma ◽  
Yuan Feng Xu ◽  
Hui Li ◽  
He Xing Li ◽  
...  
Keyword(s):  
Co Oxidation ◽  
Storage Capacity ◽  
Oxygen Storage Capacity ◽  
Oxygen Storage ◽  
X Ray Diffraction ◽  
Pd Catalysts ◽  
Transmission Electron ◽  
Pulse Experiment ◽  
Temperature Programmed

A series of Pd catalysts supported on different materials (SiO2, γ-Al2O3, CeO2, TiO2) were synthesized through precipitation reduction of palladium ions with H2. They exhibited different activity during catalytic oxidation of CO to CO2. With the characterization of N2 physisorption experiment, X-ray diffraction, transmission electron microscopy, temperature-programmed reduction, and CO and O2 multi-pulse experiment, the correlation of catalytic activity and oxygen storage capacity (OSC) of catalyst has been investigated. It was found that the reactivity is largely controlled by the OSC of the catalysts, and thus Pd/CeO2 and Pd/TiO2 were more active than Pd/SiO2 and Pd/Al2O3 for CO oxidation.

scholarly journals Influence of Intercalation-Exfoliation-Reduction Technique towards the Physico-Chemical of VPO Catalysts

2013 ◽  
Vol 2013 ◽  
pp. 1-8
Author(s):  
Y. C. Wong ◽  
Y. H. Taufiq-Yap
Keyword(s):  
Electron Microscope ◽  
X Ray Diffraction ◽  
X Ray ◽  
Vpo Catalysts ◽  
Transmission Electron ◽  
Physico Chemical ◽  
Vpo Catalyst ◽  
Temperature Programmed ◽  
Lower Temperature ◽  
Synthesized Materials

Four VPO catalysts were synthesized through intercalation and exfoliation in various alcohols and subsequent reduction of the exfoliated VOPO4sheets with various alcohols to produce VOHPO4⋅0.5H2O. The resulting VOHPO4⋅0.5H2O that undergoes the intercalation-exfoliation-reduction (IER) process will be further activated into VPO catalysts, and addition of 1 mole % Bi(NO3)3⋅5H2O in the first stage of this experiment has also being investigated. The synthesized materials were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and temperature-programmed reduction (TPR) in H2. Catalytic evaluation of the IER-treated and Bi-doped VPO catalysts was also studied on microreactor. The VPO catalyst produced through IER using 2-butanol and ethanol with addition of Bi, IERC(2Bu-Et)RBi1, gave the highest MA selectivity due to reactive O2−species released from the additional crystalline V5+phase formed by doping 1% bismuth as promoter (O2−-V5+pair) at relative lower temperature. Nevertheless, the VPO catalyst produced through IER using isobutanol, IERC(isoBu), gave the highest activity due to high amount of reactive O−species released from V4+phase (O−-V4+pair) whereby the IERC(isoBu) catalyst synthesized consists of high percentage of V4+(93 %).

Sign in / Sign up

Export Citation Format

Share Document