Effect of Devulcanized Rubber Modification on the Performance Grade, Fatigue Cracking Resistance, and Rutting Resistance of Asphalt Binders

2021 ◽  
Vol 33 (9) ◽  
pp. 04021248
Author(s):  
Salih Kocak ◽  
M. Emin Kutay
Keyword(s):  
Fatigue Cracking ◽  
Asphalt Binders ◽  
Cracking Resistance ◽  
Rutting Resistance ◽  
Performance Grade ◽  
Rubber Modification ◽  
Devulcanized Rubber

Effects of warm mix asphalt additives on performance properties of polymer modified asphalt binders

2010 ◽  
Vol 37 (1) ◽  
pp. 17-24 ◽  
Author(s):  
Hakseo Kim ◽  
Soon-Jae Lee ◽  
Serji N. Amirkhanian
Keyword(s):  
Fatigue Cracking ◽  
Warm Mix Asphalt ◽  
Asphalt Binders ◽  
Rotational Viscometer ◽  
Performance Properties ◽  
Modified Asphalt ◽  
Positive Effects ◽  
Performance Grade ◽  
Low Temperature Cracking ◽  
Polymer Modified Asphalt

This study presents an experimental evaluation for the performance properties of polymer modified asphalt (PMA) binders containing warm mix asphalt (WMA) additives. The PMA binders with the additives were produced using two of the available warm asphalt processes (i.e., Aspha-min and Sasobit) and three PMA binders graded as performance grade (PG) 76-22. The warm PMA binders were artificially short-term and then long-term aged using the rolling thin film oven (RTFO) and pressure aging vessel (PAV) procedures. Superpave binder tests were carried out on the binders through the rotational viscometer (RV), the dynamic shear rheometer (DSR), and the bending beam rheometer (BBR). In general, the results of this research indicated that (1) the addition of the WMA additives into the PMA binders showed positive effects on increasing rutting resistance at high temperature (based on the high failure temperature values from the DSR test); (2) the PMA binders containing the additives were observed to be less resistant to fatigue cracking at intermediate temperatures compared to the control PMA binders (based on the G*sin δ values at 25 °C from the DSR test); and (3) the addition of wax additive represented a possible lower resistance on low temperature cracking (based on the stiffness and the m-value at –12 °C from the BBR test).

Rheological Analysis of Performance Grade Rutting and Fatigue Cracking Criteria in Asphalt Binders

2021 ◽  
Author(s):  
Akanksha Pandey ◽  
Sumit K. Singh ◽  
Sk. Sohel Islam ◽  
G. D. Ransingchung R. N. ◽  
Sridhar Raju ◽  
...  
Keyword(s):  
Fatigue Cracking ◽  
Asphalt Binders ◽  
Rheological Analysis ◽  
Performance Grade ◽  
Analysis Of Performance

scholarly journals The Effect of Aging on the Cracking Resistance of Recycled Asphalt

2017 ◽  
Vol 2017 ◽  
pp. 1-7 ◽  
Author(s):  
Mojtaba Mohammadafzali ◽  
Hesham Ali ◽  
James A. Musselman ◽  
Gregory A. Sholar ◽  
Aidin Massahi
Keyword(s):  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Fatigue Cracking ◽  
Asphalt Mixtures ◽  
Asphalt Binders ◽  
Reclaimed Asphalt Pavement ◽  
Cracking Resistance ◽  
Recycled Asphalt ◽  
Reclaimed Asphalt ◽  
Important Concern

Fatigue cracking is an important concern when a high percentage of Reclaimed Asphalt Pavement (RAP) is used in an asphalt mixture. The aging of the asphalt binder reduces its ductility and makes the pavement more susceptible to cracking. Rejuvenators are often added to high-RAP mixtures to enhance their performance. The aging of a rejuvenated binder is different from virgin asphalt. Therefore, the effect of aging on a recycled asphalt mixture can be different from its effect on a new one. This study evaluated the cracking resistance of 100% recycled asphalt binders and mixtures and investigated the effect of aging on this performance parameter. The cracking resistance of the binder samples was tested by a Bending Beam Rheometer. An accelerated pavement weathering system was used to age the asphalt mixtures and their cracking resistance was evaluated by the Texas Overlay Test. The results from binder and mixture tests mutually indicated that rejuvenated asphalt has a significantly better cracking resistance than virgin asphalt. Rejuvenated mixtures generally aged more rapidly, and the rate of aging was different for different rejuvenators.

scholarly journals PERFORMANCE PREDICTION OF WARM MIX ASPHALT PAVEMENT CONTAINING RECLAIMED ASPHALT PAVEMENT IN RHODE ISLAND

2019 ◽  
Author(s):  
◽  
Neha Shrestha ◽  
Keyword(s):  
Surface Layer ◽  
Asphalt Pavement ◽  
Asphalt Binder ◽  
Fatigue Cracking ◽  
Thermal Cracking ◽  
Creep Recovery ◽  
Reclaimed Asphalt Pavement ◽  
Cracking Resistance ◽  
Rutting Resistance ◽  
Reclaimed Asphalt

The warm mixed asphalt (WMA) technology has gained a lot of interests in the recent years in academia, state agencies and industries. WMA technology allows reductions in production and compaction temperatures guaranteeing relevant environmental and cost saving benefits. The purpose of the present study was to study and evaluate the performance of a typical additive in WMA pavement with Reclaimed Asphalt Pavement (RAP) on rutting, fatigue cracking and thermal cracking resistance on RI Route 102. In the present study, the asphalt binder was tested at different dosages of additive using Dynamic Shear Rheometer (DSR), Rolling Thin Film Oven (RTFO), Pressure Aging Vessel (PAV), Multiple Stress Creep Recovery (MSCR) and Bending Beam Rheometer (BBR). From the overall test, it was found that 0.7% additive would lessen pavement damage due to rutting, fatigue cracking and thermal cracking. Based on the results of binder test, Hot Mix Asphalt (HMA) and WMA specimens containing 20 % RAP were prepared using PG 58-28 asphalt binder and Superpave Gyratory Compactor (SGC). From the volumetric analysis of both HMA and WMA specimens, it was determined that the optimum binder content (OBC) for HMA with 20% RAP was 5.3 percent and the OBC for WMA (0.7% additive with RAP was 5.6%. It was found that the required amount of neat regular asphalt binder for WMA specimen was higher than the one required by HMA. HMA and WMA Specimens with each containing 20% RAP were prepared at OBC and indirect tensile (IDT) strength test were conducted on that specimen. The test indicated that the performance of HMA mixtures was better than WMA with same amount of RAP. RI Route 102 was used as case study in this research study. Route 102 was rehabilitated through Full Depth Reclamation (FDR) in 2015. First half road of RI Route 102 was built with HMA base and surface layer and the other half was built with WMA base and surface layer using a typical additive. It was found that both sections have similar value in Pavement Serviceability Index (PSI) and in International Roughness Index (IRI) at this time. Four specimens were prepared to predict the performance of asphalt pavement using the dynamic modulus and the master curve. Two HMA specimens each were prepared with and without RAP. Similarly, other two WMA specimens were prepared with and without RAP. These four specimens were tested with the Asphalt Mixture Performance Tester (AMPT) machine and developed the master curves for each specimen. The results of the material testing were used to predict the performance of each test sections by using AASHTOWare Pavement ME Design (PavementME) software. It was found that the WMA-RAP performed better in fatigue cracking resistance but was found to perform poor in rutting resistance than HMA and HMA-RAP. This indicated that fatigue cracking was not a problem with WMA-RAP mixtures whereas rutting resistance still requires further investigation and improvement.

scholarly journals Rutting and Fatigue Cracking Resistance of Waste Cooking Oil Modified Trinidad Asphaltic Materials

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Rean Maharaj ◽  
Vitra Ramjattan-Harry ◽  
Nazim Mohamed
Keyword(s):  
Complex Modulus ◽  
Fatigue Cracking ◽  
Waste Cooking Oil ◽  
Cracking Resistance ◽  
Rutting Resistance ◽  
Cooking Oil ◽  
Attractive Option ◽  
Petroleum Bitumen ◽  
Resistance Decrease ◽  
Asphaltic Materials

The influence of waste cooking oil (WCO) on the performance characteristics of asphaltic materials indigenous to Trinidad, namely, Trinidad Lake Asphalt (TLA), Trinidad Petroleum Bitumen (TPB), and TLA : TPB (50 : 50) blend, was investigated to deduce the applicability of the WCO as a performance enhancer for the base asphalt. The rheological properties of complex modulus (G∗) and phase angle (δ) were measured for modified base asphalt blends containing up to 10% WCO. The results of rheology studies demonstrated that the incremental addition of WCO to the three parent binders resulted in incremental decreases in the rutting resistance (decrease inG∗/sinδvalues) and increases in the fatigue cracking resistance (decrease inG∗sinδvalue). The fatigue cracking resistance and rutting resistance for the TLA : TPB (50 : 50) blends were between those of the blends containing pure TLA and TPB. As operating temperature increased, an increase in the resistance to fatigue cracking and a decrease in the rutting resistance were observed for all of the WCO modified asphaltic blends. This study demonstrated the capability to create customized asphalt-WCO blends to suit special applications and highlights the potential for WCO to be used as an environmentally attractive option for improving the use of Trinidad asphaltic materials.

scholarly journals Performance Testing of Hot Mix Asphalt Modified with Recycled Waste Plastic

2021 ◽  
Author(s):  
Shadi Saadeh ◽  
Pritam Katawał
Keyword(s):  
Fatigue Cracking ◽  
Waste Plastics ◽  
Plastic Pollution ◽  
Cracking Resistance ◽  
Waste Plastic ◽  
Rutting Resistance ◽  
The World ◽  
Ct Test ◽  
Recycled Waste ◽  
The Ideal

Plastic pollution has become one of the major concerns in the world. Plastic waste is not biodegradable, which makes it difficult to manage waste plastic pollution. Recycling and reusing waste plastic is an effective way to manage plastic pollution. Because of the huge quantity of waste plastic released into the world, industries requiring a large amount of material, like the pavement industry, can reuse some of this mammoth volume of waste plastics. Similarly, the use of reclaimed asphalt pavement (RAP) has also become common practice to ensure sustainability. The use of recycled waste plastics and RAP in HMA mix can save material costs and conserve many pavement industries’ resources. To successfully modify HMA with RAP and waste plastic, the modified HMA should exhibit similar or better performance compared to conventional HMA. In this study, recycled waste plastic, linear low-density polyethylene (LLDPE), and RAP were added to conventional HMA, separately and together. The mechanical properties of conventional and modified HMA were examined and compared. The fatigue cracking resistance was measured with the IDEAL Cracking (IDEAL CT) test, and the Hamburg Wheel Tracking (HWT) test was conducted to investigate the rutting resistance of compacted HMA samples. The IDEAL CT test results showed that the cracking resistance was similar across plastic modified HMA and conventional HMA containing virgin aggregates. However, when 20% RAP aggregates were used in the HMA mix, the fatigue cracking resistance was found to be significantly lower in plastic modified HMA compared to conventional HMA. The rutting resistance from the HWT test at 20,000 passes was found to be similar in all conventional and modified HMA.

Fatigue Tolerance of Aged Asphalt Binders Modified with Softeners

2021 ◽  
pp. 036119812110255
Author(s):  
Javier J. García Mainieri ◽  
Punit Singhvi ◽  
Hasan Ozer ◽  
Brajendra K. Sharma ◽  
Imad L. Al-Qadi
Keyword(s):  
Shear Stress ◽  
Heavy Traffic ◽  
Asphalt Binder ◽  
Fatigue Cracking ◽  
Data Interpretation ◽  
Complex Stress ◽  
Current Data ◽  
Asphalt Binders ◽  
Failure Patterns ◽  
Peak Shear Stress

Fatigue cracking caused by repeated heavy traffic loading is a critical distress in asphalt concrete pavements and is significantly affected by the selected binder. In recent years, the growing use of recycled asphalt materials has increased the need for the production of softer asphalt binder. Various modifiers/additives are marketed to adjust the grade and/or enhance the binder performance at high and low temperatures. The modifiers are expected to alter the rheological and chemical characteristics of binders and, therefore, their performance. In this study, the damage characteristics of modified and unmodified binders, at standard long-term and extended aging conditions, were tested using the linear amplitude sweep (LAS) test. Current data-interpretation methods for LAS measurements (including AASHTO TP 101-12, T 391-20, and recent literature) showed inconsistent results for modified binders. An alternative method to interpret LAS results was developed in this study. The method considers the data until peak shear-stress is reached because complex stress states and failure patterns are observed in the specimens after that point. The proposed parameter (Δ| G*|peak τ) quantifies the reduction in complex shear modulus measured at the peak shear-stress. The parameter successfully captures the effect of aging and modification of binders.

Sign in / Sign up

Export Citation Format

Share Document