Effect of section shape, aspect ratio and thickness on the propulsive property of three-dimensional oscillating wing – a numerical study

2021 ◽  
pp. 1-11
Author(s):  
Yongcheng Li ◽  
Jijun Chen ◽  
Xijian Wang ◽  
Ziying Pan ◽  
Nan Zhang
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Section Shape

Effect of Cross Aspect Ratio on Flow in Diverging and Converging Microchannels

2017 ◽  
Vol 139 (6) ◽  
Author(s):  
V. S. Duryodhan ◽  
Shiv Govind Singh ◽  
Amit Agrawal
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Hydraulic Diameter ◽  
Working Fluid ◽  
Cross Sectional ◽  
Flow Acceleration ◽  
Three Dimensional Models

Aspect ratio is an important parameter in the study of flow through noncircular microchannel. In this work, three-dimensional numerical study is carried out to understand the effect of cross aspect ratio (height to width) on flow in diverging and converging microchannels. Three-dimensional models of the diverging and converging microchannels with angle: 2–14 deg, aspect ratio: 0.05–0.58, and Reynolds number: 130–280 are employed in the simulations with water as the working fluid. The effects of aspect ratio on pressure drop in equivalent diverging and converging microchannels are studied in detail and correlated to the underlying flow regime. It is observed that for a given Reynolds number and angle, the pressure drop decreases asymptotically with aspect ratio for both the diverging and converging microchannels. At small aspect ratio and small Reynolds number, the pressure drop remains invariant of angle in both the diverging and converging microchannels; the concept of equivalent hydraulic diameter can be applied to these situations. Onset of flow separation in diverging passage and flow acceleration in converging passage is found to be a strong function of aspect ratio, which has not been shown earlier. The existence of a critical angle with relevance to the concept of equivalent hydraulic diameter is identified and its variation with Reynolds number is discussed. Finally, the effect of aspect ratio on fluidic diodicity is discussed which will be helpful in the design of valveless micropump. These results help in extending the conventional formulae made for uniform cross-sectional channel to that for the diverging and converging microchannels.

Experimental and Numerical Study of Stall Flutter in a Transonic Low-Aspect Ratio Fan Blisk

2003 ◽  
Author(s):  
A. J. Sanders ◽  
K. K. Hassan ◽  
D. C. Rabe
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Strain Gages ◽  
Pressure Transducers ◽  
Low Aspect Ratio ◽  
Benchmark Data

Experiments are performed on a modern design transonic shroudless low-aspect ratio fan blisk that experienced both subsonic/transonic and supersonic stall-side flutter. High-response flush mounted miniature pressure transducers are utilized to measure the unsteady aerodynamic loading distribution in the tip region of the fan for both flutter regimes, with strain gages utilized to measure the vibratory response at incipient and deep flutter operating conditions. Numerical simulations are performed and compared with the benchmark data using an unsteady three-dimensional nonlinear viscous computational fluid dynamic (CFD) analysis, with the effects of tip clearance, vibration amplitude, and the number of time steps-per-cycle investigated. The benchmark data are used to guide the validation of the code and establish best practices that ensure accurate flutter predictions.

scholarly journals Experimental and Numerical Study of Flow Structures Associated With Low Aspect Ratio Elliptical Cavities

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Taravat Khadivi ◽  
Eric Savory
Keyword(s):  
Aspect Ratio ◽  
Particle Image ◽  
Numerical Study ◽  
Three Dimensional ◽  
Reynolds Stress Model ◽  
Cavity Flows ◽  
Low Aspect Ratio ◽  
Image Velocimetry ◽  
Computational Fluid Dynamics Simulations ◽  
Dynamics Simulations

The flow regimes associated with 2:1 aspect ratio elliptical planform cavities of varying depth immersed in a turbulent boundary layer at a Reynolds number of 8.7 × 104, based on the minor axis of the cavity, have been quantified from particle image velocimetry measurements and three-dimensional steady computational fluid dynamics simulations (Reynolds stress model closure). Although these elliptical cavity flows have some similarities with nominally two-dimensional and rectangular cases, three-dimensional effects due to the low aspect ratio and curvature of the walls give rise to features exclusive to low aspect ratio elliptical cavities, including formation of cellular structures at intermediate depths and vortex structures within and downstream of the cavity.

Cross-Wind Influence on Low Aspect Ratio Wings at Low Reynolds Numbers

2013 ◽  
Author(s):  
Amir Karimi Noughabi ◽  
Mehran Tadjfar
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Micro Air Vehicles ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Low Aspect Ratio ◽  
Aspect Ratios ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

The aerodynamics of the low aspect ratio (LAR) wings is of outmost importance in the performance of the fixed-wing micro air vehicles (MAVs). The flow around these wings is widely influenced by three dimensional (3D) phenomena: including wing-tip vortices, formation of laminar bubble, flow separation and reattachment, laminar to turbulent transition or any combination of these phenomena. All the recent studies consider the aerodynamic characteristics of the LAR wings under the effect of the direct wind. Here we focus on the numerical study of the influence of cross-wind on flow over the inverse Zimmerman wings with the aspect ratios (AR) between 1 and 2 at Reynolds numbers between 6×104 and 105. We have considered cross-wind’s angles from 0° to 40° and angle of attack from 0° to 12°. The results show that lift and drag coefficient generally decrease when the angle of the cross-wind is increased.

Effect of Cylinder Aspect Ratio and Channel Dimensions on the Fluid Flow and Heat Transfer in Parallel-Plate Channel Heat Exchangers

2002 ◽  
Author(s):  
A. K. Saha ◽  
Sumanta Acharya
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Aspect Ratio ◽  
Heat Exchangers ◽  
Parallel Plate ◽  
Numerical Study ◽  
Three Dimensional ◽  
Channel Height ◽  
Flow And Heat Transfer ◽  
Plate Channel

A comparative numerical study has been carried out to analyze the unsteady three-dimensional flow and heat transfer in a parallel-plate channel heat exchangers with in-line arrays of periodically mounted square cylinders (pins) at various Reynolds number and geometrical configurations. The geometry considered represents the narrow trailing edge region of the blade where pin fins are used to serve both a structural and a heat transfer role. The three-dimensional unsteady Navier-Stokes and energy equations are solved using higher order temporal and spatial discretizations. The simulations have been carried out for a range of Reynolds number based on cylinder width (180–600) and a Prandtl number of 6.99 (corresponding to water). Conjugate heat transfer calculations have been employed to account for the conduction in the solid cylinder and convection in the fluid. The thermal performance factor (TPF) increases significantly when the flow becomes unsteady. The choice of aspect ratio of the cylinders is judged by their relative increase in friction factor and heat transfer at transitional Reynolds number. The TPF is found to increase with the increase in pitch of the cylinders. The increase in channel height enhances the TPF though the heat transfer decreases at higher channel height.

Blade Lean and Shroud Leakage Flows in Low Aspect Ratio Turbines

2008 ◽  
Author(s):  
Budimir Rosic ◽  
Liping Xu
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Leakage Flow ◽  
Industrial Practice ◽  
Leakage Flows ◽  
Low Aspect Ratio ◽  
Stator Blade ◽  
Different Levels

Blade lean, i.e. non-radial blade stacking, has been intensively used over the past in the design process of low aspect ratio gas and steam turbines. Although its influence on turbine efficiency is not completely understood, it has been proved as an effective way of controlling blade loading and secondary flows on blade passage endwalls. Three-dimensional blade designs in modern industrial practice are usually carried out using clean endwalls. The influence of the leakage flows on three-dimensional blade design is traditionally neglected. This paper presents an experimental study where two different stator blades, with different levels of compound lean, were tested in a low speed three-stage model turbine with the shroud leakage flow geometry representative of industrial practice. The experimental measurements were compared with numerical tests, conducted on the same blade geometries. The influence of the compound lean on the stator flow field was analysed in detail. In order to analyse the combined effects of both the stator hub and rotor shroud leakage flow on the blade lean, in the second part of the paper a numerical study on a two stage turbine with both leakage flow paths representative of a real turbine was carried out. Performance of three different stator blade designs (two different levels of compound lean and a straight blade) was investigated. The aim of this study is to understand the mechanism and the consequence of the stator blade lean on stage performance in an environment with leakage flows and associated cavities.

Effect of Aspect Ratio on the Buoyancy Driven Reverse Flow Near the Leading Wall of Rotating Cooling Passages

1996 ◽  
Author(s):  
Prabhat Tekriwal
Keyword(s):  
Aspect Ratio ◽  
Rotation Number ◽  
Numerical Study ◽  
Reverse Flow ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Hydraulic Diameter ◽  
Flow Reversal ◽  
Aspect Ratios ◽  
Reversal Phenomenon

The present work is concerned with the flow reversal phenomenon that is caused by the centrifugal buoyancy forces in the case of three-dimensional radially outward flow through rectangular ducts rotating in orthogonal mode. Due to the flow reversal, regions of zero to low fluid velocity (stagnation) are created near the leading wall and the heat transfer, consequently, is impaired causing concerns for the design engineers. Three duct cross-sections of the same hydraulic diameter but different aspect ratios (1:1, 2:1 and 3.33:1) have been examined in this numerical study for flows at different rotation numbers and different temperature ratios. The rotation number examined ranged from 0.08 to 0.35. For each rotation number the temperature ratio is increased until the flow reversal phenomenon is observed in the CFD predictions. For all the three ducts, computations have been carried out for Reynolds number equal to 80,000. The onset of the flow reversal near the leading wall and at the exit of the single-pass flow passage is studied with the buoyancy number variation. As the aspect ratio is increased while keeping the duct hydraulic diameter fixed, the buoyancy number required to cause the onset of flow reversal decreases. Also, for each of the three ducts examined it has been found that the buoyancy number required for the predicted reverse flow to occur increases as the rotation number is increased.

Heat Transfer in a Complex Trailing Edge Passage for a High Pressure Turbine Blade: Part 2 — Simulation Results

2002 ◽  
Author(s):  
David L. Rigby ◽  
Ronald S. Bunker
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Trailing Edge ◽  
Average Aspect Ratio ◽  
Inlet Conditions ◽  
Edge Side

A combined experimental and numerical study to investigate the heat transfer distribution in a complex blade trailing edge passage was conducted. The geometry consists of a two pass serpentine passage with taper toward the trailing edge, as well as from hub to tip. The upflow channel has an average aspect ratio of roughly 14:1, while the exit passage aspect ratio is about 5:1. The upflow channel is split in an interrupted way and is smooth on the trailing edge side of the split and turbulated on the other side. A turning vane is placed near the tip of the upflow channel. Reynolds numbers in the range of 31,000 to 61,000, based on inlet conditions were simulated numerically. The simulation was performed using the Glenn-HT code, a full three-dimensional Navier-Stokes solver using the Wilcox k-ω turbulence model. A structured multi-block grid is used with approximately 4.5 million cells, and average y+ values on the order of unity. Pressure and heat transfer distributions are presented with comparison to the experimental data. While there are some regions with discrepancies, in general the agreement is very good for both pressure and heat transfer.

Experimental and Numerical Study of Stall Flutter in a Transonic Low-Aspect Ratio Fan Blisk

2004 ◽  
Vol 126 (1) ◽  
pp. 166-174 ◽  
Author(s):  
A. J. Sanders ◽  
K. K. Hassan ◽  
D. C. Rabe
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Strain Gages ◽  
Pressure Transducers ◽  
Low Aspect Ratio ◽  
Benchmark Data

Experiments are performed on a modern design transonic shroudless low-aspect ratio fan blisk that experienced both subsonic/transonic and supersonic stall-side flutter. High-response flush mounted miniature pressure transducers are utilized to measure the unsteady aerodynamic loading distribution in the tip region of the fan for both flutter regimes, with strain gages utilized to measure the vibratory response at incipient and deep flutter operating conditions. Numerical simulations are performed and compared with the benchmark data using an unsteady three-dimensional nonlinear viscous computational fluid dynamic (CFD) analysis, with the effects of tip clearance, vibration amplitude, and the number of time steps-per-cycle investigated. The benchmark data are used to guide the validation of the code and establish best practices that ensure accurate flutter predictions.

Blade Lean and Shroud Leakage Flows in Low Aspect Ratio Turbines

2011 ◽  
Vol 134 (3) ◽  
Author(s):  
Budimir Rosic ◽  
Liping Xu
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Leakage Flow ◽  
Industrial Practice ◽  
Leakage Flows ◽  
Low Aspect Ratio ◽  
Stator Blade ◽  
Different Levels

Blade lean, i.e., nonradial blade stacking, has been intensively used over the past in the design process of low aspect ratio gas and steam turbines. Although its influence on turbine efficiency is not completely understood, it has been proved as an effective way of controlling blade loading and secondary flows on blade passage endwalls. Three-dimensional blade designs in modern industrial practice are usually carried out using clean endwalls. The influence of the leakage flows on three-dimensional blade design is traditionally neglected. This paper presents an experimental study where two different stator blades, with different levels of compound lean, were tested in a low speed three-stage model turbine with the shroud leakage flow geometry representative of industrial practice. The experimental measurements were compared with numerical tests, conducted on the same blade geometries. The influence of the compound lean on the stator flow field was analyzed in detail. In order to analyze the combined effects of both the stator hub and the rotor shroud leakage flow on the blade lean, in the second part of the paper a numerical study on a two stage turbine with both leakage flow paths representative of a real turbine was carried out. Performance of three different stator blade designs (two different levels of compound lean and a straight blade) was investigated. The aim of this study is to understand the mechanism and the consequence of the stator blade lean on stage performance in an environment with leakage flows and associated cavities.

Sign in / Sign up

Export Citation Format

Share Document