Experimental and Numerical Study of Stall Flutter in a Transonic Low-Aspect Ratio Fan Blisk

2004 ◽  
Vol 126 (1) ◽  
pp. 166-174 ◽  
Author(s):  
A. J. Sanders ◽  
K. K. Hassan ◽  
D. C. Rabe
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Strain Gages ◽  
Pressure Transducers ◽  
Low Aspect Ratio ◽  
Benchmark Data

Experiments are performed on a modern design transonic shroudless low-aspect ratio fan blisk that experienced both subsonic/transonic and supersonic stall-side flutter. High-response flush mounted miniature pressure transducers are utilized to measure the unsteady aerodynamic loading distribution in the tip region of the fan for both flutter regimes, with strain gages utilized to measure the vibratory response at incipient and deep flutter operating conditions. Numerical simulations are performed and compared with the benchmark data using an unsteady three-dimensional nonlinear viscous computational fluid dynamic (CFD) analysis, with the effects of tip clearance, vibration amplitude, and the number of time steps-per-cycle investigated. The benchmark data are used to guide the validation of the code and establish best practices that ensure accurate flutter predictions.

Experimental and Numerical Study of Stall Flutter in a Transonic Low-Aspect Ratio Fan Blisk

2003 ◽  
Author(s):  
A. J. Sanders ◽  
K. K. Hassan ◽  
D. C. Rabe
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Strain Gages ◽  
Pressure Transducers ◽  
Low Aspect Ratio ◽  
Benchmark Data

Experiments are performed on a modern design transonic shroudless low-aspect ratio fan blisk that experienced both subsonic/transonic and supersonic stall-side flutter. High-response flush mounted miniature pressure transducers are utilized to measure the unsteady aerodynamic loading distribution in the tip region of the fan for both flutter regimes, with strain gages utilized to measure the vibratory response at incipient and deep flutter operating conditions. Numerical simulations are performed and compared with the benchmark data using an unsteady three-dimensional nonlinear viscous computational fluid dynamic (CFD) analysis, with the effects of tip clearance, vibration amplitude, and the number of time steps-per-cycle investigated. The benchmark data are used to guide the validation of the code and establish best practices that ensure accurate flutter predictions.

Unsteady Aerodynamics of a Low Aspect Ratio Turbine Stage: Modeling Issues and Flow Physics

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
G. Persico ◽  
A. Mora ◽  
P. Gaetani ◽  
M. Savini
Keyword(s):  
Aspect Ratio ◽  
Coming Out ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Fast Response ◽  
Operating Conditions ◽  
Pressure Probe ◽  
Turbine Stage ◽  
Time Resolved ◽  
Low Aspect Ratio

In this paper the three-dimensional unsteady aerodynamics of a low aspect ratio, high pressure turbine stage are studied. In particular, the results of fully unsteady three-dimensional numerical simulations, performed with ANSYS-CFX, are critically evaluated against experimental data. Measurements were carried out with a novel three-dimensional fast-response pressure probe in the closed-loop test rig of the Laboratorio di Fluidodinamica delle Macchine of the Politecnico di Milano. An analysis is first reported about the strategy to limit the CPU and memory requirements while performing three-dimensional simulations of blade row interaction when the rotor and stator blade numbers are prime to each other. What emerges as the best choice is to simulate the unsteady behavior of the rotor alone by applying the stator outlet flow field as a rotating inlet boundary condition (scaled on the rotor blade pitch). Thanks to the reliability of the numerical model, a detailed analysis of the physical mechanisms acting inside the rotor channel is performed. Two operating conditions at different vane incidence are considered, in a configuration where the effects of the vortex-blade interaction are highlighted. Different vane incidence angles lead to different size, position, and strength of secondary vortices coming out from the stator, thus promoting different interaction processes in the subsequent rotor channel. However some general trends can be recognized in the vortex-blade interaction: the sense of rotation and the spanwise position of the incoming vortices play a crucial role on the dynamics of the rotor vortices, determining both the time-mean and the time-resolved characteristics of the secondary field at the exit of the stage.

scholarly journals Experimental and Numerical Study of Flow Structures Associated With Low Aspect Ratio Elliptical Cavities

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Taravat Khadivi ◽  
Eric Savory
Keyword(s):  
Aspect Ratio ◽  
Particle Image ◽  
Numerical Study ◽  
Three Dimensional ◽  
Reynolds Stress Model ◽  
Cavity Flows ◽  
Low Aspect Ratio ◽  
Image Velocimetry ◽  
Computational Fluid Dynamics Simulations ◽  
Dynamics Simulations

The flow regimes associated with 2:1 aspect ratio elliptical planform cavities of varying depth immersed in a turbulent boundary layer at a Reynolds number of 8.7 × 104, based on the minor axis of the cavity, have been quantified from particle image velocimetry measurements and three-dimensional steady computational fluid dynamics simulations (Reynolds stress model closure). Although these elliptical cavity flows have some similarities with nominally two-dimensional and rectangular cases, three-dimensional effects due to the low aspect ratio and curvature of the walls give rise to features exclusive to low aspect ratio elliptical cavities, including formation of cellular structures at intermediate depths and vortex structures within and downstream of the cavity.

Cross-Wind Influence on Low Aspect Ratio Wings at Low Reynolds Numbers

2013 ◽  
Author(s):  
Amir Karimi Noughabi ◽  
Mehran Tadjfar
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Micro Air Vehicles ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Low Aspect Ratio ◽  
Aspect Ratios ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

The aerodynamics of the low aspect ratio (LAR) wings is of outmost importance in the performance of the fixed-wing micro air vehicles (MAVs). The flow around these wings is widely influenced by three dimensional (3D) phenomena: including wing-tip vortices, formation of laminar bubble, flow separation and reattachment, laminar to turbulent transition or any combination of these phenomena. All the recent studies consider the aerodynamic characteristics of the LAR wings under the effect of the direct wind. Here we focus on the numerical study of the influence of cross-wind on flow over the inverse Zimmerman wings with the aspect ratios (AR) between 1 and 2 at Reynolds numbers between 6×104 and 105. We have considered cross-wind’s angles from 0° to 40° and angle of attack from 0° to 12°. The results show that lift and drag coefficient generally decrease when the angle of the cross-wind is increased.

scholarly journals Numerical Investigations on the Blade Tip Clearance Excitation Forces in an Unshrouded Turbine

2020 ◽  
Vol 10 (4) ◽  
pp. 1532 ◽  
Author(s):  
Yang Pan ◽  
Qi Yuan ◽  
Gongge Huang ◽  
Jiawei Gu ◽  
Pu Li ◽  
...  
Keyword(s):  
Fluid Dynamic ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Geometrical Parameters ◽  
Deformation Method ◽  
Flow Angle ◽  
Rotordynamic Coefficients ◽  
Blade Tip ◽  
Positive Direct

The purpose of this study was to investigate the characteristics of the blade tip excitation forces represented as the rotordynamic coefficients (stiffness and damping coefficients) in an unshrouded turbine using the three-dimensional computational fluid dynamic (CFD) numerical method. The blade geometrical parameters were based on a SNECMA transonic experimental rig. The simulations were performed by solving the compressible Reynolds-averaged Navier–Stokes (RANS) equations. The multi-frequency elliptical whirling orbit model and an improved mesh deformation method based on the transient analysis were utilized. The effects of operating conditions on the rotordynamic coefficients and the unsteady flow were also found. The results show that the positive direct stiffness, which confirmed the direct force contribution in the tip excitation forces and the cross-coupling stiffness, were dependent on the whirling frequencies. Damping effects were shown to be negligible. The rotational speed, inlet flow angle, eccentric ratio (ER), and mean tip clearance had impacts on the stiffness, and some effects of these variables on the rotordynamic coefficients were found to be frequency dependent. Additionally, increasing the rotor eccentricity and the mean tip clearance led to the nonuniformity of the circumferential pressure distributions.

Blade Lean and Shroud Leakage Flows in Low Aspect Ratio Turbines

2008 ◽  
Author(s):  
Budimir Rosic ◽  
Liping Xu
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Leakage Flow ◽  
Industrial Practice ◽  
Leakage Flows ◽  
Low Aspect Ratio ◽  
Stator Blade ◽  
Different Levels

Blade lean, i.e. non-radial blade stacking, has been intensively used over the past in the design process of low aspect ratio gas and steam turbines. Although its influence on turbine efficiency is not completely understood, it has been proved as an effective way of controlling blade loading and secondary flows on blade passage endwalls. Three-dimensional blade designs in modern industrial practice are usually carried out using clean endwalls. The influence of the leakage flows on three-dimensional blade design is traditionally neglected. This paper presents an experimental study where two different stator blades, with different levels of compound lean, were tested in a low speed three-stage model turbine with the shroud leakage flow geometry representative of industrial practice. The experimental measurements were compared with numerical tests, conducted on the same blade geometries. The influence of the compound lean on the stator flow field was analysed in detail. In order to analyse the combined effects of both the stator hub and rotor shroud leakage flow on the blade lean, in the second part of the paper a numerical study on a two stage turbine with both leakage flow paths representative of a real turbine was carried out. Performance of three different stator blade designs (two different levels of compound lean and a straight blade) was investigated. The aim of this study is to understand the mechanism and the consequence of the stator blade lean on stage performance in an environment with leakage flows and associated cavities.

Blade Lean and Shroud Leakage Flows in Low Aspect Ratio Turbines

2011 ◽  
Vol 134 (3) ◽  
Author(s):  
Budimir Rosic ◽  
Liping Xu
Keyword(s):  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Leakage Flow ◽  
Industrial Practice ◽  
Leakage Flows ◽  
Low Aspect Ratio ◽  
Stator Blade ◽  
Different Levels

Blade lean, i.e., nonradial blade stacking, has been intensively used over the past in the design process of low aspect ratio gas and steam turbines. Although its influence on turbine efficiency is not completely understood, it has been proved as an effective way of controlling blade loading and secondary flows on blade passage endwalls. Three-dimensional blade designs in modern industrial practice are usually carried out using clean endwalls. The influence of the leakage flows on three-dimensional blade design is traditionally neglected. This paper presents an experimental study where two different stator blades, with different levels of compound lean, were tested in a low speed three-stage model turbine with the shroud leakage flow geometry representative of industrial practice. The experimental measurements were compared with numerical tests, conducted on the same blade geometries. The influence of the compound lean on the stator flow field was analyzed in detail. In order to analyze the combined effects of both the stator hub and the rotor shroud leakage flow on the blade lean, in the second part of the paper a numerical study on a two stage turbine with both leakage flow paths representative of a real turbine was carried out. Performance of three different stator blade designs (two different levels of compound lean and a straight blade) was investigated. The aim of this study is to understand the mechanism and the consequence of the stator blade lean on stage performance in an environment with leakage flows and associated cavities.

Numerical Simulation of Gas Flow and Heat Transfer in Cross-Wavy Primary Surface Channel for Microtubine Recuperators

2005 ◽  
Author(s):  
H. X. Liang ◽  
Q. W. Wang ◽  
L. Q. Luo ◽  
Z. P. Feng
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Gas Turbine ◽  
Numerical Study ◽  
High Reliability ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Flow And Heat Transfer ◽  
High Heat Transfer ◽  
The Cross

Three-dimensional numerical simulation was conducted to investigate the flow field and heat transfer performance of the Cross-Wavy Primary Surface (CWPS) recuperators for microturbines. Using high-effective compact recuperators to achieve high thermal efficiency is one of the key techniques in the development of microturbine in recent years. Recuperators need to have minimum volume and weight, high reliability and durability. Most important of all, they need to have high thermal-effectiveness and low pressure-losses so that the gas turbine system can achieve high thermal performances. These requirements have attracted some research efforts in designing and implementing low-cost and compact recuperators for gas turbine engines recently. One of the promising techniques to achieve this goal is the so-called primary surface channels with small hydraulic dimensions. In this paper, we conducted a three-dimensional numerical study of flow and heat transfer for the Cross-Wavy Primary Surface (CWPS) channels with two different geometries. In the CWPS configurations the secondary flow is created by means of curved and interrupted surfaces, which may disturb the thermal boundary layers and thus improve the thermal performances of the channels. To facilitate comparison, we chose the identical hydraulic diameters for the above four CWPS channels. Since our experiments on real recuperators showed that the Reynolds number ranges from 150 to 500 under the operating conditions, we implemented all the simulations under laminar flow situations. By analyzing the correlations of Nusselt numbers and friction factors vs. Reynolds numbers of the four CWPS channels, we found that the CWPS channels have superior and comprehensive thermal performance with high compactness, i.e., high heat transfer area to volume ratio, indicating excellent commercialized application in the compact recuperators.

Calculation of the Rise and Pitch of a Three-Dimensional Low-Aspect-Ratio Flat Ship

1991 ◽  
Vol 35 (04) ◽  
pp. 314-324
Author(s):  
Todd McComb
Keyword(s):  
Aspect Ratio ◽  
Three Dimensional ◽  
Static Case ◽  
Equilibrium Flow ◽  
Low Aspect Ratio ◽  
Fast Speed ◽  
Flow Past

Using low-aspect-ratio flat ship theory, this paper defines a procedure to determine the position of a hull which is in equilibrium at some "fast" speed in terms of a given hull shape for the same hull at rest. This procedure is then used to find the equilibrium flow past a moving ship, when given the shape of the hull at rest. The method is then extended to find the hull configuration at various speeds based on either the configuration in the static case or at some other equilibrium speed, leading to a calculation of drag versus speed. Some general formulas and some simple examples are given.

Sign in / Sign up

Export Citation Format

Share Document