scholarly journals The architecture of actin filaments and the ultrastructural location of actin-binding protein in the periphery of lung macrophages.

1986 ◽  
Vol 103 (3) ◽  
pp. 1007-1020 ◽  
Author(s):  
J H Hartwig ◽  
P Shevlin
Keyword(s):  
Electron Microscopy ◽  
Critical Point ◽  
Binding Protein ◽  
The Body ◽  
Actin Binding ◽  
Actin Network ◽  
Actin Binding Protein ◽  
Freeze Dried ◽  
Critical Point Drying ◽  
Actin Fiber

A highly branched filament network is the principal structure in the periphery of detergent-extracted cytoskeletons of macrophages that have been spread on a surface and either freeze or critical point dried, and then rotary shadowed with platinum-carbon. This array of filaments completely fills lamellae extended from the cell and bifurcates to form 0.2-0.5 micron thick layers on the top and bottom of the cell body. Reaction of the macrophage cytoskeletons with anti-actin IgG and with anti-IgG bound to colloidal gold produces dense staining of these filaments, and incubation with myosin subfragment 1 uniformly decorates these filaments, identifying them as actin. 45% of the total cellular actin and approximately 70% of actin-binding protein remains in the detergent-insoluble cell residue. The soluble actin is not filamentous as determined by sedimentation analysis, the DNAase I inhibition assay, and electron microscopy, indicating that the cytoskeleton is not fragmented by detergent extraction. The spacing between the ramifications of the actin network is 94 +/- 47 nm and 118 +/- 72 nm in cytoskeletons prepared for electron microscopy by freeze drying and critical point drying, respectively. Free filament ends are rare, except for a few which project upward from the body of the network or which extend down to the substrate. Filaments of the network intersect predominantly at right angles to form either T-shaped and X-shaped overlaps having striking perpendicularity or else Y-shaped intersections composed of filaments intersecting at 120-130 degrees angles. The actin filament concentration in the lamellae is high, with an average value of 12.5 mg/ml. The concentration was much more uniform in freeze-dried preparations than in critical point-dried specimens, indicating that there is less collapse associated with the freezing technique. The orthogonal actin network of the macrophage cortical cytoplasm resembles actin gels made with actin-binding protein. Reaction of cell cytoskeletons and of an actin gel made with actin-binding protein with anti-actin-binding protein IgG and anti-IgG-coated gold beads resulted in the deposition of clusters of gold at points where filaments intersect and at the ends of filaments that may have been in contact with the membrane before its removal with detergent. In the actin gel made with actin-binding protein, 75% of actin-fiber intersections labeled, and the filament spacing between intersections is consistent with that predicted on theoretical grounds if each added actin-binding protein molecule cross-links two filaments to form an intersection in the gel.(ABSTRACT TRUNCATED AT 400 WORDS)

scholarly journals Three-dimensional structure of actin filaments and of an actin gel made with actin-binding protein.

1983 ◽  
Vol 96 (5) ◽  
pp. 1400-1413 ◽  
Author(s):  
R Niederman ◽  
P C Amrein ◽  
J Hartwig
Keyword(s):  
Actin Filaments ◽  
Binding Protein ◽  
Three Dimensional ◽  
Actin Binding ◽  
Dimensional Structure ◽  
Molar Ratio ◽  
Computer Assisted ◽  
Three Dimensional Structure ◽  
Actin Binding Protein ◽  
Critical Point Drying

Purified muscle actin and mixtures of actin and actin-binding protein were examined in the transmission electron microscope after fixation, critical point drying, and rotary shadowing. The three-dimensional structure of the protein assemblies was analyzed by a computer-assisted graphic analysis applicable to generalized filament networks. This analysis yielded information concerning the frequency of filament intersections, the filament length between these intersections, the angle at which filaments branch at these intersections, and the concentration of filaments within a defined volume. Purified actin at a concentration of 1 mg/ml assembled into a uniform mass of long filaments which overlap at random angles between 0 degrees and 90 degrees. Actin in the presence of macrophage actin-binding protein assembled into short, straight filaments, organized in a perpendicular branching network. The distance between branch points was inversely related to the molar ratio of actin-binding protein to actin. This distance was what would be predicted if actin filaments grew at right angles off of nucleation sites on the two ends of actin-binding protein dimers, and then annealed. The results suggest that actin in combination with actin-binding protein self-assembles to form a three-dimensional network resembling the peripheral cytoskeleton of motile cells.

scholarly journals Measuring Molecular Interaction between Actin Filament and Actin Binding Protein Governing Mechanical Properties of Cross-Linked F-Actin Network

2009 ◽  
Vol 96 (3) ◽  
pp. 124a
Author(s):  
Hyungsuk Lee ◽  
Benjamin Pelz ◽  
Jorge M. Ferrer ◽  
Fumihiko Nakamura ◽  
Roger D. Kamm ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Actin Filament ◽  
Molecular Interaction ◽  
Binding Protein ◽  
Actin Binding ◽  
Actin Network ◽  
Actin Binding Protein

scholarly journals Structural comparison of several actin-binding macromolecules.

1980 ◽  
Vol 85 (2) ◽  
pp. 489-495 ◽  
Author(s):  
J M Tyler ◽  
J M Anderson ◽  
D Branton
Keyword(s):  
Electron Microscopy ◽  
Binding Protein ◽  
Actin Binding ◽  
Erythrocyte Membranes ◽  
Structural Comparison ◽  
Flexible Molecules ◽  
Actin Binding Protein ◽  
Rotary Shadowing

The cytoskeletal components, macrophage actin-binding protein and filamin, were dried from glycerol and examined by low-angle rotary shadowing electron microscopy. Both are elongate, flexible molecules whose general morphologi is similar to that of erythrocyte spectrin. Neither actin-binding protein nor filamin binds to spectrin-depleted erythrocyte membranes.

scholarly journals Scanning electron microscopy preparation and analysis of the cell cortex ultrastructure

2020 ◽  
Author(s):  
D. Flormann ◽  
M. Schu ◽  
E. Terriac ◽  
M. Koch ◽  
S. Paschke ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Critical Point ◽  
Structural Defects ◽  
Cell Cortex ◽  
Drying Methods ◽  
Actin Network ◽  
Actin Cortex ◽  
Critical Point Drying ◽  
Scanning Electron

AbstractThe cellular cortex is a 200-nm-thick actin network that lies beneath the cell membrane. It is responsible for the mechanical properties of the cell and is involved in many cellular processes, such as cell migration and interactions with the environment. To develop a clear view of the structure of this meshwork, high resolution imaging is essential, such as electron microscopy. This technique requires complex sample preparation that can lead to artifacts like shrinkage or hole formation. We present a preparation method that reduces artifacts significantly. Here, the final drying step that is typically performed by critical point drying is replaced by hexamethyldisilazane drying. We quantitatively investigated sample integrity after both preparation methods, and show that there are significant advantages of hexamethyldisilazane drying compared to critical point drying. Furthermore, automated analysis of a network is classically performed by thresholding-based software programs, which are sensitive to noise and uneven brightness of images. The here presented analysis that we have developed is based on a vectorial node algorithm. It reproduces all kinds of networks sufficiently to allow derivation of quantitative network-specific parameters, such as mesh hole size. We use this analysis to compare the network structure of cells prepared by these two drying methods, and show that hexamethyldisilazane drying leads to fewer artificial mesh holes compared to critical point drying. We thus present here a significantly improved method to quantitatively investigate the actin cortex of cells, and show that hexamethyldisilazane drying leads to more accurate imaging compared to critical point drying.Insight BoxThe highest resolution for imaging the cellular actin cortex is provided by electron microscopy. Scanning electron microscopy samples require a drying process, usually achieved by critical point drying, which is critical for the sample integrity. We compare the structural defects in the actin cortex of hTert RPE1 cells after critical point drying and a chemical based method, namely hexamethyldisilazane drying. In order to characterize the actin network, we also developed a new vectorial based tracing software. We bring here new tool, both experimental and analytical, which will help to streamline studies of the actin cortex.

scholarly journals Ultrastructural analysis of the dynactin complex: an actin-related protein is a component of a filament that resembles F-actin.

1994 ◽  
Vol 126 (2) ◽  
pp. 403-412 ◽  
Author(s):  
D A Schafer ◽  
S R Gill ◽  
J A Cooper ◽  
J E Heuser ◽  
T A Schroer
Keyword(s):  
Electron Microscopy ◽  
Binding Protein ◽  
Terminal Region ◽  
Ultrastructural Analysis ◽  
Actin Binding ◽  
Related Protein ◽  
Actin Binding Protein ◽  
Capping Protein ◽  
Short Filament ◽  
Dynactin Complex

The dynactin complex visualized by deepetch electron microscopy appears as a short filament 37-nm in length, which resembles F-actin, plus a thinner, laterally oriented filament that terminates in two globular heads. The locations of several of the constituent polypeptides were identified on this structure by applying antibodies to decorate the dynactin complex before processing for electron microscopy. Antibodies to the actin-related protein Arp1 (previously referred to as actin-RPV), bound at various sites along the filament, demonstrating that this protein assembles in a polymer similar to conventional actin. Antibodies to the barbed-end actin-binding protein, capping protein, bound to one end of the filament. Thus, an actin-binding protein that binds conventional actin may also bind to Arp1 to regulate its polymerization. Antibodies to the 62-kD component of the dynactin complex also bound to one end of the filament. An antibody that binds the COOH-terminal region of the 160/150-kD dynactin polypeptides bound to the globular domains at the end of the thin lateral filament, suggesting that the dynactin polypeptide comprises at least part of the sidearm structure.

scholarly journals A calcium- and pH-regulated protein from Dictyostelium discoideum that cross-links actin filaments.

1982 ◽  
Vol 94 (2) ◽  
pp. 466-471 ◽  
Author(s):  
J Condeelis ◽  
M Vahey
Keyword(s):  
Electron Microscopy ◽  
Dictyostelium Discoideum ◽  
Actin Filaments ◽  
Binding Protein ◽  
Actin Binding ◽  
Cross Linking ◽  
Optimal Conditions ◽  
Maximal Inhibition ◽  
Actin Binding Protein ◽  
Cross Links

We have purified an actin binding protein from amebas of Dictyostelium discoideum which we call 95,000-dalton protein (95K). This protein is rod shaped, approximately 40 nm long in the electron microscope, contains two subunits measuring 95,000 daltons each, and cross-links actin filaments. Cross-linking activity was demonstrated by using falling-ball viscometry, Ostwald viscometry, and electron microscopy. Cross-linking activity is optimal at 0.1 microM Ca++ and pH 6.8, but is progressively inhibited at higher Ca++ and pH levels over a physiological range. Half-maximal inhibition occurs at 1.6 microM free Ca++ and pH 7.3, respectively. Sedimentation experiments demonstrate that elevated Ca++ and pH inhibit the binding of 95K to F-actin which explains the loss of cross-linking activity. Electron microscopy demonstrates that under optimal conditions for cross-linking, 95K protein bundles actin filaments and that this bundling is inhibited by microM Ca++. Severing of actin filaments by 95K was not observed in any of the various assays under any of the solution conditions used. Hence, 95K protein is a rod-shaped, dimeric, Ca++- and pH-regulated actin binding protein that cross-links but does not sever actin filaments.

The Critical Point Drying Method Applied to Scanning Electron Microscopy of L-929 Cells

1970 ◽  
Vol 28 ◽  
pp. 278-279
Author(s):  
Charles TurnbiLL ◽  
Delbert E. Philpott
Keyword(s):  
Electron Microscopy ◽  
Carbon Dioxide ◽  
Surface Tension ◽  
Critical Point ◽  
Freeze Drying ◽  
Attractive Alternative ◽  
Crystal Formation ◽  
Critical Point Drying ◽  
Time Required ◽  
Scanning Electron

The advent of the scanning electron microscope (SCEM) has renewed interest in preparing specimens by avoiding the forces of surface tension. The present method of freeze drying by Boyde and Barger (1969) and Small and Marszalek (1969) does prevent surface tension but ice crystal formation and time required for pumping out the specimen to dryness has discouraged us. We believe an attractive alternative to freeze drying is the critical point method originated by Anderson (1951; for electron microscopy. He avoided surface tension effects during drying by first exchanging the specimen water with alcohol, amy L acetate and then with carbon dioxide. He then selected a specific temperature (36.5°C) and pressure (72 Atm.) at which carbon dioxide would pass from the liquid to the gaseous phase without the effect of surface tension This combination of temperature and, pressure is known as the "critical point" of the Liquid.

The Effects of Drying Techniques on Clay-Rich Soil Texture

1974 ◽  
Vol 32 ◽  
pp. 466-467
Author(s):  
T. G. Naymik
Keyword(s):  
Critical Point ◽  
Liquid Nitrogen ◽  
Liquid Nitrogen Temperature ◽  
Drying Methods ◽  
Air Drying ◽  
Freeze Dried ◽  
Critical Point Drying ◽  
Set Up ◽  
The Relationship ◽  
Quartz Grains

Three techniques were incorporated for drying clay-rich specimens: air-drying, freeze-drying and critical point drying. In air-drying, the specimens were set out for several days to dry or were placed in an oven (80°F) for several hours. The freeze-dried specimens were frozen by immersion in liquid nitrogen or in isopentane at near liquid nitrogen temperature and then were immediately placed in the freeze-dry vacuum chamber. The critical point specimens were molded in agar immediately after sampling. When the agar had set up the dehydration series, water-alcohol-amyl acetate-CO2 was carried out. The objectives were to compare the fabric plasmas (clays and precipitates), fabricskeletons (quartz grains) and the relationship between them for each drying technique. The three drying methods are not only applicable to the study of treated soils, but can be incorporated into all SEM clay soil studies.

Preservation of Plant Cell Surfaces For Scanning Electron Microscopy

1973 ◽  
Vol 31 ◽  
pp. 472-473
Author(s):  
Linda M. Sicko ◽  
Thomas E. Jensen
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Critical Point ◽  
Filter Paper ◽  
Freeze Drying ◽  
Cell Surfaces ◽  
Air Drying ◽  
Popular Method ◽  
Critical Point Drying ◽  
Scanning Electron

The use of critical point drying is rapidly becoming a popular method of preparing biological samples for scanning electron microscopy. The procedure is rapid, and produces consistent results with a variety of samples. The preservation of surface details is much greater than that of air drying, and the procedure is less complicated than that of freeze drying. This paper will present results comparing conventional air-drying of plant specimens to critical point drying, both of fixed and unfixed material. The preservation of delicate structures which are easily damaged in processing and the use of filter paper as a vehicle for drying will be discussed.

Clathrin Hub Expression Dissociates the Actin-Binding Protein Hip1R from Coated Pits and Disrupts Their Alignment with the Actin Cytoskeleton

Traffic ◽  
2001 ◽  
Vol 2 (11) ◽  
pp. 851-858 ◽  
Author(s):  
Elizabeth M. Bennett ◽  
Chih-Ying Chen ◽  
Asa E. Y. Engqvist-Goldstein ◽  
David G. Drubin ◽  
Frances M. Brodsky
Keyword(s):  
Actin Cytoskeleton ◽  
Binding Protein ◽  
Actin Binding ◽  
Coated Pits ◽  
Actin Binding Protein
Sign in / Sign up

Export Citation Format

Share Document