scholarly journals A SIMPLE FREEZE-FRACTURE REPLICATION METHOD FOR ELECTRON MICROSCOPY

1966 ◽  
Vol 29 (3) ◽  
pp. 435-447 ◽  
Author(s):  
Stanley Bullivant ◽  
Adelbert Ames
Keyword(s):  
Freeze Fracture ◽  
Practical Method ◽  
Vacuum System ◽  
Fresh Tissue ◽  
Razor Blade ◽  
Etching Technique ◽  
Simple Method ◽  
Replication Method ◽  
Structural Details ◽  
Freeze Etching

A simple method to achieve results similar to the freeze-etching technique of Moor et al. (1961) is described. The frozen tissue is cut under liquid nitrogen with a razor blade outside the evaporator rather than inside with a cooled microtome. The conditions of the experiment do not favor sublimation, and it is proposed that the structure of the replica be explained by local faults in the cleavage plane which leaves structures, such as membranes, standing above the ice. Micrographs of replicas of glycerol-protected frozen small intestine of mouse prepared by the method are presented and the structural details they show are discussed. The problem of vapor-deposited contamination is discussed. It is concluded that this is a practical method for obtaining electron micrographs that are relatively free of artifact, and that further improvements may be expected from the use of rapidly frozen fresh tissue and a clean vacuum system, possibly of the ion-pumped type.

Recent progress in the freeze-etching technique

1971 ◽  
Vol 261 (837) ◽  
pp. 121-131 ◽  
Keyword(s):  
High Vacuum ◽  
Molecular Size ◽  
Etching Technique ◽  
Structural Distortions ◽  
Shadow Casting ◽  
Structural Details ◽  
Freeze Etching ◽  
The One ◽  
Insight Into ◽  
Made In

The freeze-etching technique must be improved if structures at the molecular size level are to be seen. The limitations of the technique are discussed here together with the progress made in alleviating them. The vitrification of living specimens is limited by the fact that very high freezing rates are needed. The critical freezing rate can be lowered on the one hand by the introduction of antifreeze agents, on the other hand by the application of high hydrostatic pressure. The fracture process may cause structural distortions in the fracture face of the frozen specimen. The ‘double-replica’ method allows one to evaluate such artefacts and provides an insight into the way that membranes split. During etching there exists the danger of contaminating the fracture faces with condensable gases. Because of specimen temperatures below —110 °C, special care has to be taken in eliminating water vapour from the high vacuum. An improvement in coating freeze-etched specimens has resulted from the application of electron guns for evaporation of the highest melting-point metals. If heat transfer from gun to specimen is reduced to a minimum, Pt, Ir, Ta, W and C can be used for shadow casting. Best results are obtained with Pt-C and Ta-W . With the help of decoration effects Pt-C shadow castings give the most information about the fine structural details of the specimen.

Low temperature SEM comparisons of adjacent freeze-fractured and freeze-etched areas on frozen, hydrated samples

1995 ◽  
Vol 53 ◽  
pp. 1066-1067
Author(s):  
William P. Wergin ◽  
Eric F. Erbe ◽  
Robert W. Yaklich
Keyword(s):  
Low Temperature ◽  
Biological Samples ◽  
Freeze Fracture ◽  
Structural Components ◽  
Freeze Fracturing ◽  
Water Ice ◽  
Virus Particles ◽  
Structural Details ◽  
Freeze Etching ◽  
Sem Imaging

Most biological samples contain 70-95% water, consequently cryofixation and freeze-fracturing result in relatively smooth surfaces that exhibit few structural details. Freeze-etching, a technique that solved this problem, was initially developed for TEM observations of virus particles by Steere nearly 40 years ago. The technique, which sublimes water-ice from the surface of a fractured sample, produces surface topography that corresponds to the structural components on the freeze-etched face. This technique was further enhanced by recovering the complementary halves of a fractured sample, etching one of the surfaces and then comparing the complementary replicas from the freeze-fractured and freeze-etched faces. Recently, similar techniques were used on frozen, hydrated samples to examine complementary halves of freeze-fractured, freeze-etched specimens by low temperature SEM. Imaging complementary images of frozen, hydrated specimens in the SEM was faster than imaging complementary replicas in the TEM, however the procedure required specialized holders and was technically demanding.To simplify comparisons of freeze-fracture, freeze-etch images, samples were frozen, fractured and etched in the prechamber of an Oxford CT 1500 HF Cryotrans system that was attached to a Hitachi S-4100 FESEM.

Platinum shadowing, complementary imaging and stereo analysis: Techniques developed for TEM can now be used to increase the resolution of frozen hydrated specimens in a SEM

1993 ◽  
Vol 51 ◽  
pp. 70-71
Author(s):  
William P. Wergin ◽  
Eric F. Erbe
Keyword(s):  
Surface Characteristics ◽  
Biological Specimen ◽  
Etching Technique ◽  
Surface Information ◽  
Analysis Techniques ◽  
Stereo Analysis ◽  
Transmission Electron ◽  
Wide Range ◽  
Structural Details ◽  
Freeze Etching

In 1957, Steere froze virus crystals, fractured and transferred them to a vacuum evaporator where they were etched, shadowed and coated. The coating, which was then removed from the tissue and mounted on a grid, represented a replica that could be observed in the transmission electron microscope (TEM). This accomplishment is regarded as the first successful biological application of the freeze-etching technique in electron microscopy. This technique was further advanced by describing procedures whereby the replicas from both surfaces of a frozen, fractured sample could be recovered. This pair of replicas provided additional surface information by allowing one to view and compare the two opposing surfaces, or the complementary images, of a freeze-fractured biological specimen. Using a goniometer stage the replicas were also photographed, tilted and rephotographed to produce stereo pairs that could be used to analyze three-dimensionally the surface characteristics of the replica. Until recently these TEM techniques have been the principle procedures utilized by biologists to gain high resolution structural details about virus crystals, biological membranes and a wide range of other material.

Replication of Wet Objects and Cells

1974 ◽  
Vol 32 ◽  
pp. 102-103
Author(s):  
S. Basu ◽  
D. F. Parsons
Keyword(s):  
Water Vapor Pressure ◽  
High Vacuum ◽  
Polystyrene Latex ◽  
Vacuum System ◽  
Saturated Water Vapor ◽  
Replication Method ◽  
New Methods ◽  
Saturated Water ◽  
Water Vapors ◽  
Intermediate Chamber

We are approaching the invasiveness of cancer cells from the studies of their wet surface morphology which should distinguish them from their normal counterparts. In this report attempts have been made to provide physical basis and background work to a wet replication method with a differentially pumped hydration chamber (Fig. 1) (1,2), to apply this knowledge for obtaining replica of some specimens of known features (e.g. polystyrene latex) and finally to realize more specific problems and to improvize new methods and instrumentation for their rectification. In principle, the evaporant molecules penetrate through a pair of apertures (250, 350μ), through water vapors and is, then, deposited on the specimen. An intermediate chamber between the apertures is pumped independently of the high vacuum system. The size of the apertures is sufficiently small so that full saturated water vapor pressure is maintained near the specimen.

Structures Formed by Cryoprotective Agents Used in Freezc-Etching

1971 ◽  
Vol 29 ◽  
pp. 448-449
Author(s):  
G. G. Cocks ◽  
C. E. Cluthe
Keyword(s):  
Aqueous Solution ◽  
Polyethylene Oxide ◽  
Liquid Nitrogen Temperature ◽  
Ice Crystals ◽  
Etching Technique ◽  
Structural Constituent ◽  
Cryoprotective Agents ◽  
Quick Freezing ◽  
Freeze Etching ◽  
Fractured Surface

The freeze etching technique is potentially useful for examining dilute solutions or suspensions of macromolecular materials. Quick freezing of aqueous solutions in Freon or propane at or near liquid nitrogen temperature produces relatively large ice crystals and these crystals may damage the structures to be examined. Cryoprotective agents may reduce damage to the specimem, hut their use often results in the formation of a different set of specimem artifacts.In a study of the structure of polyethylene oxide gels glycerol and sucrose were used as cryoprotective agents. The experiments reported here show some of the structures which can appear when these cryoprotective agents are used.Figure 1 shows a fractured surface of a frozen 25% aqueous solution of sucrose. The branches of dendritic ice crystals surrounded hy ice-sucrose eutectic can be seen. When this fractured surface is etched the ice in the dendrites sublimes giving the type of structure shown in Figure 2. The ice-sucrose eutectic etches much more slowly. It is the smooth continuous structural constituent surrounding the branches of the dendrites.

Freeze-Fracture Replication of Frozen Outer Segments of Rat Retinal Rods

1969 ◽  
Vol 27 ◽  
pp. 392-393
Author(s):  
Thomas S. Leeson ◽  
C. Roland Leeson
Keyword(s):  
Electron Microscopy ◽  
Cross Section ◽  
Outer Segment ◽  
Freeze Fracture ◽  
X Ray Diffraction ◽  
X Ray ◽  
Outer Segments ◽  
Retinal Rods ◽  
Temperature Electron ◽  
Freeze Etching

Numerous previous studies of outer segments of retinal receptors have demonstrated a complex internal structure of a series of transversely orientated membranous lamellae, discs, or saccules. In cones, these lamellae probably are invaginations of the covering plasma membrane. In rods, however, they appear to be isolated and separate discs although some authors report interconnections and some continuities with the surface near the base of the outer segment, i.e. toward the inner segment. In some species, variations have been reported, such as longitudinally orientated lamellae and lamellar whorls. In cross section, the discs or saccules show one or more incisures. The saccules probably contain photolabile pigment, with resulting potentials after dipole formation during bleaching of pigment. Continuity between the lamina of rod saccules and extracellular space may be necessary for the detection of dipoles, although such continuity usually is not found by electron microscopy. Particles on the membranes have been found by low angle X-ray diffraction, by low temperature electron microscopy and by freeze-etching techniques.

Freeze-fracture cytochemistry: A goal set by Russell Steere in 1957

1993 ◽  
Vol 51 ◽  
pp. 60-61
Author(s):  
Nicholas J Severs
Keyword(s):  
Chemical Nature ◽  
Biological Systems ◽  
Freeze Fracture ◽  
Structural Components ◽  
Major Goal ◽  
Membrane Biology ◽  
Routine Application ◽  
The Future ◽  
Freeze Etching

In his pioneering demonstration of the potential of freeze-etching in biological systems, Russell Steere assessed the future promise and limitations of the technique with remarkable foresight. Item 2 in his list of inherent difficulties as they then stood stated “The chemical nature of the objects seen in the replica cannot be determined”. This defined a major goal for practitioners of freeze-fracture which, for more than a decade, seemed unattainable. It was not until the introduction of the label-fracture-etch technique in the early 1970s that the mould was broken, and not until the following decade that the full scope of modern freeze-fracture cytochemistry took shape. The culmination of these developments in the 1990s now equips the researcher with a set of effective techniques for routine application in cell and membrane biology.Freeze-fracture cytochemical techniques are all designed to provide information on the chemical nature of structural components revealed by freeze-fracture, but differ in how this is achieved, in precisely what type of information is obtained, and in which types of specimen can be studied.

Rate of Sublimation of Ice by Radiative Heating in Freeze-Etching

1980 ◽  
Vol 38 ◽  
pp. 618-619
Author(s):  
Yeshayahu Talmon
Keyword(s):  
Heat Flux ◽  
Freeze Fracture ◽  
Constant Heat Flux ◽  
Radiative Heating ◽  
Constant Heat ◽  
Entire Sample ◽  
Simplified Method ◽  
Freeze Etching ◽  
Sublimation Rates ◽  
Fractured Surface

To bring out details in the fractured surface of a frozen sample in the freeze fracture/freeze-etch technique,the sample or part of it is warmed to enhance water sublimation.One way to do this is to raise the temperature of the entire sample to about -100°C to -90°C. In this case sublimation rates can be calculated by using plots such as Fig.1 (Talmon and Thomas),or by simplified formulae such as that given by Menold and Liittge. To achieve higher rates of sublimation without heating the entire sample a radiative heater can be used (Echlin et al.). In the present paper a simplified method for the calculation of the rates of sublimation under a constant heat flux F [W/m2] at the surface of the sample from a heater placed directly above the sample is described.

Sign in / Sign up

Export Citation Format

Share Document