A Hybrid Plasma De-icing Actuator by Using SiC hydrophobic Coating-Based Quartz Glass as Barrier Dielectric

Author(s):  
Xing Zheng ◽  
Huimin Song ◽  
Bian Dongliang ◽  
Hua Liang ◽  
Haohua Zong ◽  
...  
2018 ◽  
pp. 68-72
Author(s):  
Yu. K. Taranenko ◽  
O. Yu. Oliynyk ◽  
N. A. Minakova ◽  
E. V. Titova

Author(s):  
Noriyuki Nomoto ◽  
Yoshitomi Okazaki ◽  
Kenji Kuroda ◽  
Shunji Takenoiri ◽  
Toyonobu Yoshida

2008 ◽  
Author(s):  
Wei Guo ◽  
Zeng Bo Wang ◽  
Lin Li ◽  
Zhu Liu ◽  
Boris Luk’yanchuk ◽  
...  

Author(s):  
Tino Petsch ◽  
Bernd Keiper ◽  
Günter Reiße ◽  
Steffen Weißmantel ◽  
Robby Ebert ◽  
...  

Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 212
Author(s):  
Ming-Jun Liao ◽  
Li-Qiang Duan

The influence of different wettability on explosive boiling exhibits a significant distinction, where the hydrophobic surface is beneficial for bubble nucleation and the hydrophilic surface enhances the critical heat flux. Therefore, to receive a more suitable surface for the explosive boiling, in this paper a hybrid hydrophobic–hydrophilic nanostructured surface was built by the method of molecular dynamics simulation. The onset temperatures of explosive boiling with various coating thickness, pillar width, and film thicknesses were investigated. The simulation results show that the hybrid nanostructure can decrease the onset temperature compared to the pure hydrophilic surface. It is attributed to the effect of hydrophobic coating, which promotes the formation of bubbles and causes a quicker liquid film break. Furthermore, with the increase of the hydrophobic coating thickness, the onset temperature of explosive boiling decreases. This is because the process of heat transfer between the liquid film and the hybrid nanostructured surface is inevitably enhanced. In addition, the onset temperature of explosive boiling on the hybrid wetting surface decreases with the increase of pillar width and liquid film thickness.


Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 151
Author(s):  
Yuyang Liu ◽  
Chang-Hwan Choi

Sand, a cheap and naturally abundant particulate material, was modified with photocatalytic and hydrophobic coatings to reduce evaporation loss and facilitate the purification of water. The first-level photocatalytic coatings (TiO2 or ZnO nanocrystals) rendered nanoscale roughness on the surface of the sand. The additional second-level hydrophobic coating of a self-assembled monolayer of octyltrimethoxysilane (OTS) made the sand particles superhydrophobic because of the nanoscale roughness imposed by the nanocrystals. The superhydrophobic sand particles, floating on the free surface of water due to their superhydrophobicity, significantly reduced the evaporation loss of water by 60%–90% in comparison to an uncovered water surface. When the outer hydrophobic coatings are weathered or disengaged, the inner photocatalytic coatings become exposed to water. Then, the sand particles act as photocatalysts to degrade the contaminants in water under solar radiation.


2013 ◽  
Vol 753 ◽  
pp. 505-509
Author(s):  
Yuichi Sato ◽  
Toshifumi Suzuki ◽  
Hiroyuki Mogami ◽  
Fumito Otake ◽  
Hirotoshi Hatori ◽  
...  

Solid phase growth of thin films of copper (Cu), aluminum (Al) and zinc oxide (ZnO) on single crystalline sapphire and quartz glass substrates were tried by heat-treatments and their crystallization conditions were investigated. ZnO thin films relatively easily recrystallized even when they were deposited on the amorphous quartz glass substrate. On the other hand, Cu and Al thin films hardly recrystallized when they were deposited on the quartz glass substrate. The metal thin films could be recrystallized at only extremely narrow windows of the heat-treatment conditions when they were deposited on the single crystalline sapphire substrate. The window of the solid phase heteroepitaxial growth condition of the Al film was wider than that of the Cu film.


Friction ◽  
2021 ◽  
Author(s):  
Pengcheng Li ◽  
Chongyang Tang ◽  
Xiangheng Xiao ◽  
Yanmin Jia ◽  
Wanping Chen

AbstractThe friction between nanomaterials and Teflon magnetic stirring rods has recently drawn much attention for its role in dye degradation by magnetic stirring in dark. Presently the friction between TiO2 nanoparticles and magnetic stirring rods in water has been deliberately enhanced and explored. As much as 1.00 g TiO2 nanoparticles were dispersed in 50 mL water in 100 mL quartz glass reactor, which got gas-closed with about 50 mL air and a Teflon magnetic stirring rod in it. The suspension in the reactor was magnetically stirred in dark. Flammable gases of 22.00 ppm CO, 2.45 ppm CH4, and 0.75 ppm H2 were surprisingly observed after 50 h of magnetic stirring. For reference, only 1.78 ppm CO, 2.17 ppm CH4, and 0.33 ppm H2 were obtained after the same time of magnetic stirring without TiO2 nanoparticles. Four magnetic stirring rods were simultaneously employed to further enhance the stirring, and as much as 30.04 ppm CO, 2.61 ppm CH4, and 8.98 ppm H2 were produced after 50 h of magnetic stirring. A mechanism for the catalytic role of TiO2 nanoparticles in producing the flammable gases is established, in which mechanical energy is absorbed through friction by TiO2 nanoparticles and converted into chemical energy for the reduction of CO2 and H2O. This finding clearly demonstrates a great potential for nanostructured semiconductors to utilize mechanical energy through friction for the production of flammable gases.


Sign in / Sign up

Export Citation Format

Share Document