scholarly journals Influence of Desert Sand and Cooling Regime on the Compressive Strength of High Strength Concrete after High Temperatures

2020 ◽  
Vol 712 ◽  
pp. 012019
Author(s):  
M H Zhang ◽  
H F Liu ◽  
S Tian ◽  
Y C Ma ◽  
S I Doh
Keyword(s):  
Compressive Strength ◽  
High Temperatures ◽  
High Strength Concrete ◽  
High Strength ◽  
Cooling Regime ◽  
Strength Concrete ◽  
Desert Sand

Analysis of Post-Combustion High-Strength Concrete Compressive Strength Using Polypropylene Fibers

2020 ◽  
Vol 26 (1) ◽  
pp. 118-127
Author(s):  
Teuku Budi Aulia ◽  
Muttaqin Muttaqin ◽  
Mochammad Afifuddin ◽  
Zahra Amalia
Keyword(s):  
Compressive Strength ◽  
Thermal Stress ◽  
Silica Fume ◽  
High Temperatures ◽  
High Strength Concrete ◽  
High Strength ◽  
Polypropylene Fibers ◽  
Concrete Compressive Strength ◽  
Strength Concrete ◽  
Maximum Value

High-strength concrete is vulnerable to high temperatures due to its high density. The use of polypropylene fibers could prevent structure explosion by forming canals due to melted fibers during fire, thus release its thermal stress. This study aims to determine the effect of polypropylene fibers on compressive strength of high-strength concrete after combustion at 400ºC for five hours. High-strength concrete was made by w/c-ratio 0.3 with cement amount 550 kg/m3 and added with silica fume 8% and superplasticizer 4% by cement weight. The variations of polypropylene fibers were 0%, 0.2% and 0.4% of concrete volume. The compression test was carried out on standard cylinders Ø15/30 cm of combustion and without combustion specimens at 7 and 28 days. The results showed that compressive strength of high-strength concretes without using polypropylene fibers decreased in post-combustion compared with specimens without combustion, i.e., 0.81% at 7 days and 23.42% at 28 days. Conversely, the use of polypropylene fibers can increase post-combustion compressive strength with a maximum value resulted in adding 0.2% which are 25.52% and 10.44% at 7 and 28 days respectively. It can be concluded that the use of polypropylene fibers is effective to prevent reduction of high-strength concrete compressive strength that are burned at high temperatures.

Effects of Nano-CaCO3 on the Compressive Strength and Microstructure of High Strength Concrete in Different Curing Temperature

2011 ◽  
Vol 121-126 ◽  
pp. 126-131 ◽  
Author(s):  
Qing Lei Xu ◽  
Tao Meng ◽  
Miao Zhou Huang
Keyword(s):  
Compressive Strength ◽  
Low Temperature ◽  
High Strength Concrete ◽  
High Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Strength Concrete ◽  
Calcium Nitrite ◽  
Orientation Index ◽  
Early Strength

In this paper, effects of nano-CaCO3 on compressive strength and Microstructure of high strength concrete in standard curing temperature(21±1°C) and low curing temperature(6.5±1°C) was studied. In order to improve the early strength of the concrete in low temperature, the early strength agent calcium nitrite was added into. Test results indicated that 0.5% dosage of nano-CaCO3 could inhibit the effect of calcium nitrite as early strength agent, but 1% and 2% dosage of nano-CaCO3 could improve the strength of the concrete by 13% and 18% in standard curing temperature and by 17% and 14% in low curing temperature at the age of 3days. According to the XRD spectrum, with the dosage up to 1% to 2%, nano-CaCO3 can change the orientation index significantly, leading to the improvement of strength of concrete both in standard curing temperature and low curing temperature.

scholarly journals MECHANICAL PROPERTIES OF HIGH STRENGTH CONCRETE AT HIGH TEMPERATURES

2008 ◽  
Vol 73 (624) ◽  
pp. 341-347 ◽  
Author(s):  
Masashi MATSUDO ◽  
Hirokazu NISHIDA ◽  
Takahiro OHTSUKA ◽  
Takeo HIRASHIMA ◽  
Takeo ABE
Keyword(s):  
Mechanical Properties ◽  
High Temperatures ◽  
High Strength Concrete ◽  
High Strength ◽  
Strength Concrete

Comparison Analysis on the Mechanical Properties of HSC and NSC after the Action of High Temperatures

2014 ◽  
Vol 1014 ◽  
pp. 49-52
Author(s):  
Xiao Ping Su
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Temperatures ◽  
High Strength Concrete ◽  
Elasticity Modulus ◽  
Strain Curve ◽  
Peak Stress ◽  
High Strength ◽  
Peak Strain ◽  
Strength Concrete

With the wide application of high strength concrete in the building construction,the risk making concrete subject to high temperatures during a fire is increasing. Comparison tests on the mechanical properties of high strength concrete (HSC) and normal strength concrete (NSC) after the action of high temperature were made in this article, which were compared from the following aspects: the peak stress, the peak strain, elasticity modulus, and stress-strain curve after high temperature. Results show that the laws of the mechanical properties of HSC and NSC changing with the temperature are the same. With the increase of heating temperature, the peak stress and elasticity modulus decreases, while the peak strain grows rapidly. HSC shows greater brittleness and worse fire-resistant performance than NSC, and destroys suddenly. The research and evaluation on the fire-resistant performance of HSC should be strengthened during the structural design and construction on the HSC buildings.

Effect of Chopped Basalt Fiber on the Fresh and Hardened Properties of Fly Ash High Strength Concrete

2014 ◽  
Vol 567 ◽  
pp. 381-386 ◽  
Author(s):  
Nasir Shafiq ◽  
Muhd Fadhil Nuruddin ◽  
Ali Elheber Ahmed Elshekh ◽  
Ahmed Fathi Mohamed Salih
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Basalt Fiber ◽  
High Strength ◽  
Progressive Increase ◽  
Test Results ◽  
Strength Concrete ◽  
Hardened Properties ◽  
Chopped Basalt Fiber

In order to improve the mechanical properties of high strength concrete, HSC, several studies have been conducted using fly ash, FA. Researchers have made it possible to achieve 100-150MPa high strength concrete. Despite the popularity of this FAHSC, there is a major shortcoming in that it becomes more brittle, resulting in less than 0.1% tensile strain. The main objective of this work was to evaluate the fresh and hardened properties of FAHSC utilizing chopped basalt fiber stands, CBFS, as an internal strengthening addition material. This was achieved through a series of experimental works using a 20% replacement of cement by FA together with various contents of CBFS. Test results of concrete mixes in the fresh state showed no segregation, homogeneousness during the mixing period and workability ranging from 60 to 110 mm. Early and long terms of compressive strength did not show any improvement by using CBFS; in fact, it decreased. This was partially substituted by the effect of FA. Whereas, the split and flexural strengths of FASHC were significantly improved with increasing the content of CBFS as well as the percentage of the split and flexural tensile strength to the compressive strength. Also, test results showed a progressive increase in the areas under the stress-strain curves of the FAHSC strains after the CBFS addition. Therefore, the brittleness and toughness of the FAHSC were enhanced and the pattern of failure moved from brittle failure to ductile collapse using CBFS. It can be considered that the CBFS is a suitable strengthening material to produce ductile FAHSC.

Influence of Nano Particles in the Flexural Behavior of High-Strength Reinforced Concrete Beams

2021 ◽  
Vol 1160 ◽  
pp. 25-43
Author(s):  
Naglaa Glal-Eldin Fahmy ◽  
Rasha El-Mashery ◽  
Rabiee Ali Sadeek ◽  
L.M. Abd El-Hafaz
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Reinforced Concrete Beams ◽  
Nano Particles ◽  
Flexural Behavior ◽  
Single Type ◽  
Strength Concrete ◽  
Flexural Ductility

High strength concrete (HSC) characterized by high compressive strength but lower ductility compared to normal strength concrete. This low ductility limits the benefit of using HSC in building safe structures. Nanomaterials have gained increased attention because of their improvement of mechanical properties of concrete. In this paper we present an experimental study of the flexural behavior of reinforced beams composed of high-strength concrete and nanomaterials. Eight simply supported rectangular beams were fabricated with identical geometries and reinforcements, and then tested under two third-point loads. The study investigated the concrete compressive strength (50 and 75 N/mm2) as a function of the type of nanomaterial (nanosilica, nanotitanium and nanosilica/nanotitanium hybrid) and the nanomaterial concentration (0%, 0.5% and 1.0%). The experimental results showed that nano particles can be very effective in improving compressive and tensile strength of HSC, nanotitanium is more effective than nanosilica in compressive strength. Also, binary usage of hybrid mixture (nanosilica + nanotitanium) had a remarkable improvement appearing in compressive and tensile strength than using the same percentage of single type of nanomaterials used separately. The reduction in flexural ductility due to the use of higher strength concrete can be compensated by adding nanomaterials. The percentage of concentration, concrete grade and the type of nanomaterials, could predominantly affect the flexural behavior of HSRC beams.

scholarly journals SHEAR STRENGTH OF RC BEAMS WITHOUT STIRRUP USING HIGH-STRENGTH CONCRETE OF COMPRESSIVE STRENGTH RANGING TO 130MPa

2003 ◽  
pp. 75-91
Author(s):  
Motoyuki SUZUKI ◽  
Mitsuyoshi AKIYAMA ◽  
Wei Lun WANG ◽  
Masayoshi SATO ◽  
Naomi MAEDA ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Shear Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Rc Beams ◽  
Strength Concrete

Estimation of Compressive Strength of Recycled Aggregate High Strength Concrete Using Ultrasonic Pulse Velocity

2014 ◽  
Vol 605 ◽  
pp. 147-150
Author(s):  
Seong Uk Hong ◽  
Seung Hun Kim ◽  
Yong Taeg Lee
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
Coarse Aggregate ◽  
High Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Recycled Aggregate ◽  
Strength Concrete ◽  
Recycled Coarse Aggregate

This study used the ultrasonic pulse velocity method, one of the non-destructive test methods that does not damage the building for maintenance of to-be-constructed concrete structures using recycled aggregates in order to estimate the compressive strength of high strength concrete structure using recycled coarse aggregate and provide elementary resources for technological establishment of ultrasonic pulse velocity method. 200 test pieces of high strength concrete 40, 50MPa using recycled coarse aggregate were manufactured by replacement rates (0, 30, 50, 100%) and age (1, 7, 28, 180days), and air curing was executed to measure compressive strength and wave velocity. As the result of compressive strength measurement, the one with age of 180day and design strength of 40MPa was 43.69MPa, recycled coarse aggregate replacement rate of 30% 50% 100% were 42.82, 41.22, 37.35MPa, and 50MPa was 52.50MPa, recycled coarse aggregate replacement rate of 30% 50% 100% were 49.02, 46.66, 45.30MPa, and while it could be seen that the test piece substituted with recycled aggregate was found to have lower strength than the test piece with natural aggregate only, but it still reached the design strength to a degree. The correlation of compressive strength and ultrasonic pulse velocity was found and regression analysis was conducted. The estimation formula for compressive strength of high strength concrete using recycled coarse aggregate was found to be Fc=0.069Vp4.05, R2=0.66

Sign in / Sign up

Export Citation Format

Share Document