scholarly journals Comparative Study on Turbulence Models of High-Speed Centrifugal Pump with Low Specific Speed

2020 ◽  
Vol 740 ◽  
pp. 012038
Author(s):  
Xiaoyu Li ◽  
Yunguang Ji ◽  
Hongbin Cui ◽  
Shuqi Xue
Keyword(s):  
Comparative Study ◽  
Centrifugal Pump ◽  
High Speed ◽  
Turbulence Models ◽  
Low Specific Speed ◽  
Specific Speed

New Centrifugal Pump in Very Low Specific Speed Range

2011 ◽  
Author(s):  
Shusaku Kagawa ◽  
Junichi Kurokawa
Keyword(s):  
Centrifugal Pump ◽  
High Speed ◽  
Cfd Simulation ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Rotating Disk ◽  
Capacity Curve ◽  
Speed Range ◽  
Low Specific Speed ◽  
Specific Speed

In the range of very low specific speed, such as ns < 80 [min.−1, m3/min., m], or Ns < 533 [min.−1, USGPM, ft.], stable head-capacity curve is one of the most important issues. The head-capacity curve of a conventional closed impeller tends to be unstable with a positive slope characteristic in such a very low ns range. To solve this problem, a new type of centrifugal pump “J-groove pump” is proposed and tested in this study. The J-groove pump is composed of a rotating disk mounted with many shallow radial grooves and a circular casing. The experimental results reveal that the proposed J-groove pump is quite effective in the very low specific speed range. The pump head is about 1.2 times higher than that of a conventional centrifugal pump and the head-capacity curve is almost stable, though the efficiency becomes a little lower because of a large friction power of the stationary wall. The cavitation performance is also measured and is shown to be almost same as that of a conventional centrifugal pump. This pump is applicable to high speed pump, as it has no small clearance, high strength due to simple impeller configuration, and easy to assemble. In order to determine the internal flow characteristics of the J-groove pump, CFD simulation is carried out. It is revealed that the high head of the J-groove pump is caused by a strong vortex flow existing in both clearances near the impeller tip over the whole flow range.

Effects of Volute Curvature on Performance of a Low Specific-Speed Centrifugal Pump at Design and Off-Design Conditions

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Hamed Alemi ◽  
Seyyed Ahmad Nourbakhsh ◽  
Mehrdad Raisee ◽  
Amir Farhad Najafi
Keyword(s):  
Centrifugal Pump ◽  
Cross Section ◽  
Constant Velocity ◽  
Rectangular Cross Section ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Turbulence Models ◽  
Radial Force ◽  
Low Specific Speed ◽  
Specific Speed

The effects of the volute geometry on the head, efficiency, and radial force of a low specific-speed centrifugal pump were investigated focusing on off-design conditions. This paper is divided into three parts. In the first part, the three-dimensional flow inside the pump with rectangular volute was simulated using three well-known turbulence models. Simulation results were compared with the available experimental data, and an acceptable agreement was obtained. In the second part, two volute design methods, namely, the constant velocity and the constant angular momentum were investigated. Obtained results showed that in general the constant velocity method gives more satisfactory performance. In the third part, three volutes with different cross section and diffuser shape were designed. In general, it was found that circular cross section volute with radial diffuser provides higher head and efficiency. Moreover, the minimum radial force occurs at higher flowrate in circular volute geometry comparing to rectangular cross section volute.

Rotating Cavitation in a Centrifugal Pump Impeller of Low Specific Speed

2002 ◽  
Vol 124 (2) ◽  
pp. 356-362 ◽  
Author(s):  
Jens Friedrichs ◽  
Gu¨nter Kosyna
Keyword(s):  
Centrifugal Pump ◽  
High Speed ◽  
Incidence Angle ◽  
Normal Operation ◽  
Pump Impeller ◽  
Wide Range ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Cavity Closure ◽  
Operating Points

The paper describes an experimental investigation of two similar centrifugal pump impellers of low specific speed. Both impellers show rotating cavitation over a wide range of part load operating points. The occurrence of this phenomenon produces a characteristic shape of creeping head-drop compared to the more usual sudden head-drop at “normal” operation points. The onset of rotating cavitation can be assigned to a certain value of the parameter σ/2α meaning the cavity volume in relation to the incidence angle. Optical analysis by video and high-speed camera techniques illustrates the development of this instability mechanism which is mainly driven by an interaction of the cavity closure region and the following blade. Combining these observations and the results of a fourier-transformation the characteristic propagation frequencies of rotating cavitation can be presented for one impeller.

scholarly journals The flow simulation of a low-specific-speed high-speed centrifugal pump

2011 ◽  
Vol 35 (1) ◽  
pp. 242-249 ◽  
Author(s):  
B. Jafarzadeh ◽  
A. Hajari ◽  
M.M. Alishahi ◽  
M.H. Akbari
Keyword(s):  
Centrifugal Pump ◽  
High Speed ◽  
Flow Simulation ◽  
Low Specific Speed ◽  
Specific Speed

Theory and application of two-dimension viscous hydraulic design of the ultra-low specific-speed centrifugal pump

2019 ◽  
Vol 234 (1) ◽  
pp. 58-71 ◽  
Author(s):  
Cong Wang ◽  
Yongxue Zhang ◽  
Hucan Hou ◽  
Zhiyi Yuan
Keyword(s):  
Boundary Layer ◽  
Centrifugal Pump ◽  
Diagnostic Model ◽  
Two Dimension ◽  
Cavitation Performance ◽  
Hydraulic Design ◽  
Displacement Thickness ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Low Efficiency

Low efficiency and bad cavitation performance restrict the development of the ultra-low specific-speed centrifugal pump (ULSSCP). In this research, combined turbulent boundary layer theory with two-dimension design and two-dimension viscous hydraulic design method has been proposed to redesign a ULSSCP. Through the solution of the displacement thickness in the boundary layer, a less curved blade profile with a larger outlet angle was obtained. Then the hydraulic and cavitation performance of the reference pump and the designed pump were numerically studied. The comparison of performance of the reference pump calculated by the numerical and experimental results revealed a better agreement. Research shows that the average hydraulic efficiency and head of the designed pump improve by 2.9% and 3.3%, respectively. Besides, the designed pump has a better cavitation performance. Finally, through the internal flow analysis with entropy production diagnostic model, a 24.8% drop in head loss occurred in the designed pump.

Optimal hydraulic design of an ultra-low specific speed centrifugal pump based on the local entropy production theory

2019 ◽  
Vol 233 (6) ◽  
pp. 715-726 ◽  
Author(s):  
Hucan Hou ◽  
Yongxue Zhang ◽  
Xin Zhou ◽  
Zhitao Zuo ◽  
Haisheng Chen
Keyword(s):  
Entropy Production ◽  
Centrifugal Pump ◽  
Orthogonal Design ◽  
High Energy ◽  
Geometrical Parameters ◽  
Production Theory ◽  
Local Entropy ◽  
Hydraulic Design ◽  
Low Specific Speed ◽  
Specific Speed

The ultra-low specific speed centrifugal pump has been widely applied in aerospace engineering, metallurgy, and other industrial fields. However, its hydraulic design lacks specialized theory and method. Moreover, the impeller and volute are designed separately without considering their coupling effect. Therefore, the optimal design is proposed in this study based on the local entropy production theory. Four geometrical parameters are selected to establish orthogonal design schemes including blade outlet setting angle, wrapping angle volute inlet width, and throat area. Subsequently, a 3D steady flow with Reynolds stress turbulent model and energy equation model is numerically conducted and the entropy production is calculated by a user-defined function code. The range analysis is made to identify the optimal scheme indicating that the combination of local entropy production and orthogonal design is feasible on pump optimization. The optimal pump is visibly improved with an increase of 1.08% in efficiency. Entropy production is decreased by 16.75% and 6.03% in impeller and volute, respectively. High energy loss areas are captured and explained in terms of helical vortex and wall friction, and the turbulent and wall entropy production are respectively reduced by 3.82% and 14.34% for the total pump.

scholarly journals Optimal Design of Slit Impeller for Low Specific Speed Centrifugal Pump Based on Orthogonal Test

2021 ◽  
Vol 9 (2) ◽  
pp. 121
Author(s):  
Yang Yang ◽  
Ling Zhou ◽  
Hongtao Zhou ◽  
Wanning Lv ◽  
Jian Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Large Scale ◽  
Internal Flow ◽  
Orthogonal Test ◽  
Centrifugal Pumps ◽  
Initial Model ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Four Levels

Marine centrifugal pumps are mostly used on board ship, for transferring liquid from one point to another. Based on the combination of orthogonal testing and numerical simulation, this paper optimizes the structure of a drainage trough for a typical low-specific speed centrifugal pump, determines the priority of the various geometric factors of the drainage trough on the pump performance, and obtains the optimal impeller drainage trough scheme. The influence of drainage tank structure on the internal flow of a low-specific speed centrifugal pump is also analyzed. First, based on the experimental validation of the initial model, it is determined that the numerical simulation method used in this paper is highly accurate in predicting the performance of low-specific speed centrifugal pumps. Secondly, based on the three factors and four levels of the impeller drainage trough in the orthogonal test, the orthogonal test plan is determined and the orthogonal test results are analyzed. This work found that slit diameter and slit width have a large impact on the performance of low-specific speed centrifugal pumps, while long and short vane lap lengths have less impact. Finally, we compared the internal flow distribution between the initial model and the optimized model, and found that the slit structure could effectively reduce the pressure difference between the suction side and the pressure side of the blade. By weakening the large-scale vortex in the flow path and reducing the hydraulic losses, the drainage trough impellers obtained based on orthogonal tests can significantly improve the hydraulic efficiency of low-specific speed centrifugal pumps.

Sign in / Sign up

Export Citation Format

Share Document