Prediction of permeability of 5-harness satin fabric by a modified kozeny constant determined from experiments

2021 ◽  
Author(s):  
Dong-Cheol Park ◽  
Yun-Hae Kim ◽  
Soo-Jeong Park ◽  
Do-Hoon Shin ◽  
TianYu Yu
Keyword(s):  
Fiber Volume Fraction ◽  
Prediction Models ◽  
Volume Fraction ◽  
Simulation Analysis ◽  
Flow Simulation ◽  
Reference Value ◽  
Liquid Composite Molding ◽  
Carbon Fabric ◽  
Fiber Volume ◽  
Kozeny Constant

Abstract Permeability is a critical parameter not only in flow simulation analysis but also in liquid composite molding (LCM) process. When a liquid resin is infused into a dry preform, the impregnation is mainly characterized by the permeability. The permeability of a dry preform can be obtained through theoretical and experimental methods. In the theoretical estimation of permeability, the effects of fiber arrangement as well as fabric type and form for various types of preforms are not sufficiently reflected in the calculation. Thus, there is a gap between the theoretical and experimental permeability. Recently, experimental determination has been gaining considerable attention as a mean to obtain accurate permeability values; however, it requires a number of trials. In this study, the permeability of the Hexforce G0926 5HS (5-harness satin) carbon fabric preform is estimated using representative theoretical prediction models, the Gebart and Kozeny–Carman equations. In addition to the Kozeny–Carman permeability (using the Kozeny constant values from literature), the Kozeny constant obtained through experiments was used to obtain a modified Kozeny–Carman permeability. All three calculated permeabilities were compared and verified with the fabric manufacturer’s reference value. The results showed that the modified Kozeny–Carman permeability using the experimentally determined Kozeny constant was closest to the reference value at 57% fiber volume fraction. Further, the predicted permeability was compared with other experimental permeability values from literature over the 40%–65% range of fiber volume fraction. We found that the modified Kozeny–Carman permeability once again came closest to the literature values. Finally, an optimized fitting equation was proposed to replace the Kozeny–Carman equation for predicting the permeability of Hexforce G0926 5HS carbon fabric over the 40%–65% fiber volume fraction range.

Optical measurement of local permeability of flax fiber fabrics before liquid composite molding

2018 ◽  
Vol 52 (24) ◽  
pp. 3289-3297 ◽  
Author(s):  
Benoît Cosson
Keyword(s):  
Optical Method ◽  
Fiber Volume Fraction ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Optical Measurement ◽  
Transmission Measurement ◽  
Liquid Composite Molding ◽  
Fiber Volume ◽  
Filling Time ◽  
Composite Molding

Tracking the variability of natural fiber-based fabrics properties, such as local areal weight, fiber volume fraction, and therefore permeability, is crucial to optimize the parts processing of the bio-composites. This paper aims at developing a cost-effective and efficient optical method in order to predict the permeability of flax fabrics used in liquid composite molding processes. This method using an LCD monitor as light source and a reflex camera as a measurement device is based on light transmission measurement through fabric thickness. The raw data given by the camera are gray scale maps, transformed into areal weight maps. FEM software based on levelset method is finally used to highlight the influence of the local variability of the fiber volume fraction, and of the related fabrics porosity and permeability on the mold filling time. The proposed method can be directly implemented on the manufacturing line of the composites. It can be used to optimize, part-to-part, the resin consumption by predicting the resin flow through perform. Interestingly, this novel optical method is auto-calibrated and does not depend on picture resolution.

Effect of Fiber Content on Void Morphology in Resin Transfer Molded E-Glass/Epoxy Composites

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Youssef K. Hamidi ◽  
Sudha Dharmavaram ◽  
Levent Aktas ◽  
M. Cengiz Altan
Keyword(s):  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Void Formation ◽  
Areal Density ◽  
Fiber Content ◽  
Epoxy Composites ◽  
Formation Mechanisms ◽  
Liquid Composite Molding ◽  
Fiber Volume ◽  
Composite Molding

Effect of fiber volume fraction on occurrence, morphology, and spatial distribution of microvoids in resin transfer molded E-glass/epoxy composites is investigated. Three disk-shaped center-gated composite parts containing 8, 12, and 16 layers of randomly-oriented, E-glass fiber perform are molded, yielding 13.5%, 20.5%, and 27.5% fiber volume fractions. Voids are evaluated by microscopic image analysis of the samples obtained along the radius of these disk-shaped composites. The number of voids is found to decrease moderately with increasing fiber content. Void areal density decreased from 10.5 voids/mm2 to 9.5 voids/mm2 as fiber content is increased from 13.5% to 27.5%. Similarly, void volume fraction decreased from 3.1% to 2.5%. Increasing fiber volume fraction from 13.5% to 27.5% is found to lower the contribution of irregularly-shaped voids from 40% of total voids down to 22.4%. Along the radial direction, combined effects of void formation by mechanical entrapment and void mobility are shown to yield a spatially complex void distribution. However, increasing fiber content is observed to affect the void formation mechanisms as more voids are able to move toward the exit vents during molding. These findings are believed to be applicable not only to resin transfer molding but generally to liquid composite molding processes.

Pressurized Infusion: A New and Improved Liquid Composite Molding Process

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
M. Akif Yalcinkaya ◽  
Gorkem E. Guloglu ◽  
Maya Pishvar ◽  
Mehrad Amirkhosravi ◽  
E. Murat Sozer ◽  
...  
Keyword(s):  
Spatial Distribution ◽  
Composite Laminates ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Compaction Pressure ◽  
External Pressure ◽  
Void Content ◽  
Liquid Composite Molding ◽  
Molding Process ◽  
Fiber Volume

Vacuum-assisted resin transfer molding (VARTM) has several inherent shortcomings such as long mold filling times, low fiber volume fraction, and high void content in fabricated laminates. These problems in VARTM mainly arise from the limited compaction of the laminate and low resin pressure. Pressurized infusion (PI) molding introduced in this paper overcomes these disadvantages by (i) applying high compaction pressure on the laminate by an external pressure chamber placed on the mold and (ii) increasing the resin pressure by pressurizing the inlet resin reservoir. The effectiveness of PI molding was verified by fabricating composite laminates at various levels of chamber and inlet pressures and investigating the effect of these parameters on the fill time, fiber volume fraction, and void content. Furthermore, spatial distribution of voids was characterized by employing a unique method, which uses a flatbed scanner to capture the high-resolution planar scan of the fabricated laminates. The results revealed that PI molding reduced fill time by 45%, increased fiber volume fraction by 16%, reduced void content by 98%, improved short beam shear (SBS) strength by 14%, and yielded uniform spatial distribution of voids compared to those obtained by conventional VARTM.

scholarly journals Formation of Resin-Rich Zones in Composites Processing

2010 ◽  
Vol 123-125 ◽  
pp. 543-546 ◽  
Author(s):  
Chen Song Dong ◽  
Tze Chiun Tsai
Keyword(s):  
Composite Structures ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Liquid Composite Molding ◽  
Fiber Volume ◽  
Factors Affecting ◽  
Composite Molding ◽  
Composites Processing ◽  
Stress And Deformation ◽  
Fiber Preforms

Resin-rich zones are a common phenomenon in liquid composite molding processes. These resin-rich zones cause unwanted residual stress and deformation, and part-to-part variation, and thus they need to be studied in the design of composite structures. An experimental study on the formation of resin-rich zones in angled composite parts is presented in this paper. Two open-channel mold sets were designed and fabricated. Fiber preforms were loaded into these molds and the gaps formed were visually inspected by a microscope. The influences of corner radius, fiber volume fraction, enclosed angle, and stacking sequence were investigated, and significant factors affecting gap thickness were identified by Design of Experiments (DOE). It can be concluded from the experimental results that: 1) Fiber volume fraction is the most significant factor affecting gap thickness. Gap thickness is inversely proportional to fiber volume fraction; 2) Gap thickness is inversely proportional to radius; 3) The gap thickness of unidirectional preforms is larger than that of the cross-ply preforms.

Effect of Fiber Content on Void Morphology in Resin Transfer Molded E-Glass/Epoxy Composites

2005 ◽  
Author(s):  
Youssef K. Hamidi ◽  
Sudha Dharmavaram ◽  
Levent Aktas ◽  
M. Cengiz Altan
Keyword(s):  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Void Formation ◽  
Areal Density ◽  
Fiber Content ◽  
Epoxy Composites ◽  
Formation Mechanisms ◽  
Liquid Composite Molding ◽  
Fiber Volume ◽  
Equivalent Radius

Effect of fiber volume fraction on occurrence, morphology, and spatial distribution of microvoids in resin transfer molded E-glass/epoxy composites is investigated. Three disk-shaped center-gated composite parts containing 8, 12, and 16 layers of randomly-oriented, E-glass fiber perform are molded, yielding 13.5, 20.5 and 27.5% fiber volume fractions, respectively. Voids throughout these disk-shaped composites are evaluated by microscopic image analysis of samples obtained along the radius. Each identified void’s equivalent radius, area, and shape are determined at 200x magnification. Number of voids is found to decrease moderately with increasing fiber content. Void areal density decreased from 10.5 to 9.5 voids/mm2 as fiber content is increased from 13.5 to 27.5% fiber content. Similarly, void volume fraction decreased from 3.1 to 2.5%. Average void size is observed to remain similar at 53 to 55 μm when the fiber content is increased from 13.5 to 27.5%. Increasing fiber volume fraction from 13.5 to 27.5% lowers the contribution of irregularly-shaped voids from 40% of total voids down to 22.4%. Along the radial direction, combined effects of void formation by mechanical entrapment and void mobility are shown to yield a spatially complex void distribution. However, increasing fiber content is observed to affect the void formation mechanisms as more voids are able to move towards the exit vents during molding. These findings are believed to be applicable not only to resin transfer molding, but generally to liquid composite molding processes.

Monitoring of mechanical properties of prestressed glass fiber epoxy composites over 12 months after fabrication

2021 ◽  
pp. 002199832110047
Author(s):  
Mahmoud Mohamed ◽  
Siddhartha Brahma ◽  
Haibin Ning ◽  
Selvum Pillay
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Flexural Strength ◽  
Compressive Residual Stress ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Epoxy Composites ◽  
Flexural Properties ◽  
Initial Increase ◽  
Fiber Volume

Fiber prestressing during matrix curing can significantly improve the mechanical properties of fiber-reinforced polymer composites. One primary reason behind this improvement is the generated compressive residual stress within the cured matrix, which impedes cracks initiation and propagation. However, the prestressing force might diminish progressively with time due to the creep of the compressed matrix and the relaxation of the tensioned fiber. As a result, the initial compressive residual stress and the acquired improvement in mechanical properties are prone to decline over time. Therefore, it is necessary to evaluate the mechanical properties of the prestressed composites as time proceeds. This study monitors the change in the tensile and flexural properties of unidirectional prestressed glass fiber reinforced epoxy composites over a period of 12 months after manufacturing. The composites were prepared using three different fiber volume fractions 25%, 30%, and 40%. The results of mechanical testing showed that the prestressed composites acquired an initial increase up to 29% in the tensile properties and up to 32% in the flexural properties compared to the non-prestressed counterparts. Throughout the 12 months of study, the initial increase in both tensile and flexural strength showed a progressive reduction. The loss ratio of the initial increase was observed to be inversely proportional to the fiber volume fraction. For the prestressed composites fabricated with 25%, 30%, and 40% fiber volume fraction, the initial increase in tensile and flexural strength dropped by 29%, 25%, and 17%, respectively and by 34%, 26%, and 21%, respectively at the end of the study. Approximately 50% of the total loss took place over the first month after the manufacture, while after the sixth month, the reduction in mechanical properties became insignificant. Tensile modulus started to show a very slight reduction after the fourth/sixth month, while the flexural modulus reduction was observed from the beginning. Although the prestressed composites displayed time-dependent losses, their long-term mechanical properties still outperformed the non-prestressed counterparts.

scholarly journals Effect of Fiber Volume Fraction on Behavior of Concrete Beams Made with Recycled Concrete Aggregates

2019 ◽  
Vol 253 ◽  
pp. 02004
Author(s):  
Wael Alnahhal ◽  
Omar Aljidda
Keyword(s):  
Fiber Volume Fraction ◽  
Concrete Beams ◽  
Volume Fraction ◽  
Recycled Concrete ◽  
Flexural Behavior ◽  
Beam Specimen ◽  
Rc Beam ◽  
Fiber Volume ◽  
Concrete Aggregates ◽  
Recycled Concrete Aggregates

This study investigates the effect of using different volume fractions of basalt macro fibers (BMF) on the flexural behavior of concrete beams made with 100% recycled concrete aggregates (RCA) experimentally. A total of 4 reinforced concrete (RC) beam specimens were flexural tested until failure. The parameter investigated included the BMF volume fraction (0%, 0.5%, 1%, and 1.5%). The testing results of the specimens were compared to control beam specimen made with no added fibers. The experimental results showed that adding BMF improves the flexural capacity of the tested beams.

Sign in / Sign up

Export Citation Format

Share Document