scholarly journals Underlying role of mechanical rigidity and topological constraints in physical sputtering and reactive ion etching of amorphous materials

2018 ◽  
Vol 2 (5) ◽  
Author(s):  
Gyanendra Bhattarai ◽  
Shailesh Dhungana ◽  
Bradley J. Nordell ◽  
Anthony N. Caruso ◽  
Michelle M. Paquette ◽  
...  
Keyword(s):  
Amorphous Materials ◽  
Reactive Ion Etching ◽  
Ion Etching ◽  
Topological Constraints ◽  
Physical Sputtering ◽  
Mechanical Rigidity

Reactive Ion Etching of GaSb, (Ai,Ga)Sb, and InAs for Novel Device Applications.

1990 ◽  
Vol 216 ◽  
Author(s):  
D.C. La Tulipe ◽  
D.J. Frank ◽  
H. Munekata
Keyword(s):  
Etch Rate ◽  
Reactive Ion Etching ◽  
Scanning Electron Micrographs ◽  
Electrical Characteristics ◽  
Ion Etching ◽  
Novel Device ◽  
Physical Sputtering ◽  
Chlorine Gas ◽  
Device Applications ◽  
Scanning Electron

ABSTRACT-Although a variety of novel device proposals for GaSb/(Al,Ga)Sb/InAs heterostructures have been made, relatively little is known about processing these materials. We have studied the reactive ion etching characteristics of GaSb, (AI,Ga)Sb, and InAs in both methane/ hydrogen and chlorine gas chemistries. At conditions similar to those reported elsewhere for RIE of InP and GaAs in CH4/H2, the etch rate of (AI,Ga)Sb was found to be near zero, while GaSb and InAs etched at 200Å/minute. Under conditions where the etch mechanism is primarily physical sputtering, the three compounds etch at similar rates. Etching in Cl2 was found to yield anisotropic profiles, with the etch rate of (AI,Ga)Sb increasing with Al mole fraction, while InAs remains unetched. Damage to an InAs “stop layer” was investigated by sheet resistance and mobility measurements. These etching techniques were used to fabricate a novel InAs-channel FET composed of these materials. Several scanning electron micrographs of etching results are shown along with preliminary electrical characteristics.

Characterization of Sidewall Residue Film and Atomic Structure of the Trench Formed by BCI3/CI2 Reactive Ion Etching

1989 ◽  
Vol 158 ◽  
Author(s):  
Sun Jin Yun ◽  
Young-Jin Jeon ◽  
Jeong Y. Lee
Keyword(s):  
Photoelectron Spectroscopy ◽  
Secondary Ion Mass Spectrometry ◽  
Reactive Ion Etching ◽  
Surface Region ◽  
Bottom Surface ◽  
Silicon Substrates ◽  
Ion Etching ◽  
Transmission Electron ◽  
Physical Sputtering ◽  
20 Nm

ABSTRACTThe silicon trench etching in BCl3/Cl2 reactive ion etching plasma leads to the intrinsic bonding damage, the permeations of etching species and impurities into silicon substrates, and the deposition of residue film on trench sidewall. The contaminations and the damages in trench were investigated by using high resolution transmission electron microscopy (HRTEM), secondary ion mass spectrometry (SIMS), and x-ray photoelectron spectroscopy (XPS). The microstructure of the rounded bottom surface showed that the surface region was distorted by 2 - 6 atomic layers and the trench etch was mainly limited by the physical sputtering-like mechanism. The damage in the silicon lattice consisted of prominent planar defects roughly confined to {110} and {111} planes. The thickness of sidewall residue film was 10 - 90 nm, which was thinner at deeper region of the trench, whereas that of residue film at the trench bottom was 1.5 - 3.5 nm. The SIMS results of no-patterned specimen presented that the permeation depths of boron and chlorine into the Si-substrate were about 40 and 20 nm, respectively. The presence of BxCly and Cl-related Si chemical states was identified from XPS analysis of the residue film.

Fabrication of Micro-Gap Structure by Reactive Ion Etching Technique (RIE) for Future Reproductivity of Nanogap Biosensor

2015 ◽  
Vol 1109 ◽  
pp. 64-68
Author(s):  
Q. Humayun ◽  
U. Hashim
Keyword(s):  
Reactive Ion Etching ◽  
Electrical Characterization ◽  
Coated Sample ◽  
Etching Time ◽  
Semiconductor Surface ◽  
Etching Technique ◽  
Ion Etching ◽  
Gap Spacing ◽  
Gap Structure

The important role of reactive ion etching (RIE) technique is to etch the semiconductor surface directionally. The purpose of the current research is to fabricate polysilicon micro-gap structures by RIE technique for future biosensing application. Therefore zero-gap microstructure of butterfly topology was designed by using AutoCAD software and finally the designed was transferred to commercial chrome glass photomask. Ploysilicon wafer samples were selected to achieve high conductivity during electrical characterization measurement. The fabrication process starts from samples resist coating and then by employing photolithography through chrome glass photomask the zero-gap pattern of butterfly topology was transferred to resist coated sample wafer followed by resist stripping from exposed area and finally by reactive ion etching (RIE) technique the open area of polysilicon was etched directionally at different etching time to fabricate micro-gap structure on wafer samples. The spacing of fabricated micro-gap structures will be further shrink by thermal oxidation (size reduction technique) until to nanosize gap spacing. The proposed nanospacing gap will definitely show the capability to detect the bio molecule when inserted into the gap spacing.

Kinetics of Reactive Ion Etching of Polymers in an Oxygen Plasma: The Importance of Direct Reactive Ion Etching

1993 ◽  
Vol 334 ◽  
Author(s):  
Sandra W. Graham ◽  
Christoph SteinbrüChel
Keyword(s):  
Polymer Films ◽  
Langmuir Probe ◽  
Oxygen Plasma ◽  
Reactive Ion Etching ◽  
Surface Chemical ◽  
Ion Etching ◽  
Modified Model ◽  
Physical Sputtering ◽  
The Relationship ◽  
Kinetics Of

AbstractThe etching of polymer films in oxygen-based plasmas has been studied between 5 and 100 mTorr in a reactive ion etch reactor using Langmuir probe and optical actinometry measurements. Results for the etch yield (the number of carbon atoms removed per incident ion) are analyzed in terms of a surface-chemical model for ion-enhanced etching proposed by Joubert et al. (J. Appl. Phys. 65, 5096 (1989)). A proper description of the results requires that this model be modified by including a term due to direct reactive ion etching and physical sputtering. The contribution by direct reactive ion etching to the overall etching turns out to be significant under all conditions and even dominant at the lowest pressures. The modified model should be applicable to the etching of polymers in other types of reactors, especially highplasma- density reactors. The relationship between these results and the anisotropic patterning of polymer films is also discussed.

The Role of F Atoms in the Reactive Sputter Etching of Silicon Dioxide: Langmuir Probe and Optical Actinometry Measurements

1986 ◽  
Vol 76 ◽  
Author(s):  
C H. Steinbrüchel ◽  
B. J. Curtis
Keyword(s):  
Silicon Dioxide ◽  
Langmuir Probe ◽  
Constant Pressure ◽  
Reactive Ion Etching ◽  
Ion Flux ◽  
The Other ◽  
Ion Fluxes ◽  
Ion Etching ◽  
Sputter Etching

ABSTRACTReactive sputter etching of SiO2 in a low-pressure CF4 -O2 plasma has been investigated using a Langmuir probe to determine ion fluxes to the substrate and optical actinometry to monitor the concentration of F atoms, [F]. Etch yields Y, i.e. the number of substrate atoms removed per impinging ion, are obtained vs O2 composition and vs pressure. At constant pressure Y decreases slightly, but [F] increases considerably, with increasing O2 content. On the other hand, at constant O2 composition both Y and [F] increase strongly with increasing pressure. These results suggest that at low [F], relative to the ion flux to the substrate, the dominant etch mechanism is direct reactive ion etching, with the ions themselves as the main reactants, whereas at high [F] the overall etching is ion-enhanced, with F atoms as the main neutral reactants.

Sign in / Sign up

Export Citation Format

Share Document