Next-generation ETMT 8800 electrothermal mechanical test system

1990 ◽  
Vol 194 ◽  
Author(s):  
Erica Robertson ◽  
Mary Ann Hill ◽  
Ricardo B. Schwarz

AbstractFusion zone microstructures of an electron beam (EB) welded XDt m Ti–48at%Al + 6.5 vol% TiB2 alloy revealed plate-like precipitates which were absent in the base metal. The volume fraction of this phase increased with increasing cooling rate and correlated with increased weld cracking frequency. To determine whether this phase was a product of solidification from the melt or a product of a solid-state transformation, the microstructures of the welds were compared to those of samples cycled in a Gleeble 1500/20 Thermal-Mechanical Test System which was programmed to simulate the solid-state portion of the weld cooling rates (as predicted by a Rosenthal analysis). The microstructures were characterized by X-ray diffraction, optical and by scanning electron microscopy. The plate-like phase found in the weld microstructures was identified as TiB2 occurring upon rapid solidification of the melted weld metal.


1993 ◽  
Vol 115 (2) ◽  
pp. 179-186 ◽  
Author(s):  
S. B. Brown ◽  
V. R. Dave

Although rate-change experiments are essential for characterizing rate-dependent flow, certain nonobvious aspects of test machine dynamic response and control system strategies can distort rate-change data. These distortions are large enough to cause rate-change experiments to characterize the test system dynamic response instead of the test material’s rate dependence. We demonstrate that both relaxation and strain rate change experiments exhibit this potential distortion of test data. Investigators performing these experiments must therefore examine control error carefully to assure that the experiments are valid. We demonstrate that the standard PID control modes normally used in servocontrolled mechanical test equipment will generate error. Either P or PD control modes are more appropriate for rate-change experiments.


2012 ◽  
Vol 594-597 ◽  
pp. 290-293
Author(s):  
Yong Jie Yang ◽  
Ming Fu Guo ◽  
Dong Wei Chen

Generally surrounding rocks of deep mine show the typical creep characteristics and the multi stage loading creep test of coal was carried out by MTS815 rock mechanical test system in this paper. Compared to the creep coefficient of other rocks, creep coefficient of coal is relatively small. Coal creep failure changes obviously when load level is higher than the threshold stress. The constitutive characteristics of creep failure of coal can be fitted preferably by the Cubic Polynomial.


2014 ◽  
Vol 936 ◽  
pp. 1948-1952 ◽  
Author(s):  
Li Chu Zhou ◽  
Yu Fei Zhao ◽  
Feng Fang

In this paper, pearlitic steel wire with/without reserved texture were investigated with the help of mechanical test system, scanning electron microscope (SEM) and XRD. Experimental result shows that: Tensile strength of two wire are almost same. After cold drawn tensile strength of wire with reserved texture are higher than tensile strength of the without one. Before cold drawn, two wires have same microstructure of isometric pearlite and after drawing the wire with reserved texture has less shear deformed pearlitic colony. Intensity of <110> fiber texture in the wire with reserved texture are stronger than the without one at all strains. The stronger <110> texture mean the orientation of α-ferrite lamella were more closely and improve working hardening rate of pearlitic wire.


Author(s):  
James H. Wiley ◽  
Kalp Mathur ◽  
Aaron M. Brown ◽  
Shelley A. Wright ◽  
Maren Cosens ◽  
...  

2019 ◽  
Author(s):  
James M. Pflug ◽  
Valerie Renee Holmes ◽  
Crystal Burrus ◽  
J. Spencer Johnston ◽  
David R. Maddison

ABSTRACTMeasuring genome size across different species can yield important insights into evolution of the genome and allow for more informed decisions when designing next-generation genomic sequencing projects. New techniques for estimating genome size using shallow genomic sequence data have emerged which have the potential to augment our knowledge of genome sizes, yet these methods have only been used in a limited number of empirical studies. In this project, we compare estimation methods using next-generation sequencing (k-mer methods and average read depth of single-copy genes) to measurements from flow cytometry, the gold standard for genome size measures, using ground beetles (Carabidae) and other members of the beetle suborder Adephaga as our test system. We also present a new protocol for using read-depth of single-copy genes to estimate genome size. Additionally, we report flow cytometry measurements for five previously unmeasured carabid species, as well as 21 new draft genomes and six new draft transcriptomes across eight species of adephagan beetles. No single sequence-based method performed well on all species, and all tended to underestimate the genome sizes, although only slightly in most samples. For one species, Bembidion haplogonum, most sequence-based methods yielded estimates half the size suggested by flow cytometry. This discrepancy for k-mer methods can be explained by a large number of repetitive sequences, but we have no explanation for why read-depth methods yielded results that were also strikingly low.


Aerospace ◽  
2003 ◽  
Author(s):  
D. Ruan ◽  
G. Lu ◽  
B. Wang

Aluminium foam is a type of cellular materials and offers potential for lightweight structures and energy absorbers in automotive and aerospace industries. They may be subject to multiaxial loads in these applications and it is essential to have a failure criterion in terms of the stresses which cause yield. Three criteria have been proposed so far. Gibson and Ashby deduced a yield surface by using dimentional arguments for ideal, isotropic, homogenous foams. Miller’s yield surface was based on the model of Drucker and Prager, which was originally proposed as a model for soil. It incorporated a linear and quadratic dependence on the pressure. Deshpande and Fleck modified the yield criterion of solid metals to account for the effect of porosity on the yield criterion for a metallic foam. In this paper, triaxial tests of CYMAT aluminium foams were conducted by using MTS (Mechanical Test System) with a Hoek Cell to investigate their yield surfaces experimentally. Five types of aluminium foams with nominal relative densities. of 5%, 10%, 15%, 17% and 20% were tested for a range of axisymmetric compressive stress states. Experimental results were compared with three theoretical criteria. Triaxial tests at various strain rates (from 10−4 to 10+1 s−1) were also performed in this paper to investigate the influence of strain rate on the yield surface.


Author(s):  
Alexander Ahlert ◽  
D. Zeitvogel ◽  
J. Neubeck ◽  
W. Krantz ◽  
J. Wiedemann ◽  
...  

2011 ◽  
Vol 464 ◽  
pp. 506-509 ◽  
Author(s):  
W. Zhu ◽  
Jian Zhong Zhou ◽  
M Wang ◽  
Shu Huang ◽  
Deng Hui Wei ◽  
...  

Micro-scale laser shock peening (μLSP) is a flexible and precise process that can potentially be applied to metallic structures in micro devices to improve strength and reliability performance. In order to understand the mechanism of μLSP process, a typical experiment was carried out for copper foils specimen with various process parameters. Surface morphology, deformation and hardness of the specimens were observed and characterized by 3D microscope system and situ nano-mechanical test system respectively. It was found that overlapping rate of laser spot has a little effect on microscopic deformation depth which increases slowly with the increasing of laser energy, and micro-hardness of the laser treated specimens was improved significantly.


Sign in / Sign up

Export Citation Format

Share Document