Stator–rotor interaction in the tip leakage flow of an inlet vaned low-speed axial fan

2020 ◽  
Vol 30 (10) ◽  
pp. 4425-4452
Author(s):  
Adrián Vazquez Gonzalez ◽  
Andrés Meana-Fernández ◽  
Jesús Manuel Fernández
Keyword(s):  
Flow Rate ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Axial Fan ◽  
Content Type ◽  
Periodic Fluctuation ◽  
Low Speed ◽  
Tip Leakage ◽  
Partial Load ◽  
Load Conditions

Purpose The purpose of the paper is to quantify the impact of the non-uniform flow generated by the upstream stator on the generation and convection of the tip leakage flow (TLF) structures in the passages of the rotor blades in a low-speed axial fan. Design/methodology/approach A full three dimensional (3D)-viscous unsteady Reynolds-averaged Navier-stokes (RANS) (URANS) simulation of the flow within a periodic domain of the axial stage has been performed at three different flow rate coefficients (φ = 0.38, 0.32, 0.27) using ReNormalization Group k-ε turbulence modelling. A typical tip clearance of 2.3 per cent of the blade span has been modelled on a reduced domain comprising a three-vaned stator and a two-bladed rotor with circumferential periodicity. A non-conformal grid with hybrid meshing, locally refined O-meshes on both blades and vanes walls with (100 × 25 × 80) elements, a 15-node meshed tip gap and circumferential interfaces for sliding mesh computations were also implemented. The unsteady motion of the rotor has been covered with 60 time steps per blade event. The simulations were validated with experimental measurements of the static pressure in the shroud of the blade tip region. Findings It has been observed that both TLF and intensities of the tip leakage vortex (TLV) are significantly influenced by upstream stator wakes, especially at nominal and partial load conditions. In particular, the leakage flow, which represents 12.4 per cent and 11.3 per cent of the working flow rate, respectively, has shown a clear periodic fluctuation clocked with the vane passing period in the relative domain. The periodic fluctuation of the TLF is in the range of 2.8-3.4 per cent of the mean value. In addition, the trajectory of the tip vortex is also notably perturbed, with root-mean squared fluctuations reaching up to 18 per cent and 6 per cent in the regions of maximum interaction at 50 per cent and 25 per cent of the blade chord for nominal and partial load conditions, respectively. On the contrary, the massive flow separation observed in the tip region of the blades for near-stall conditions prevents the formation of TLV structures and neglects any further interaction with the upstream vanes. Research limitations/implications Despite the increasing use of large eddy simulation modelling in turbomachinery environments, which requires extremely high computational costs, URANS modelling is still revealed as a useful technique to describe highly complex viscous mechanisms in 3D swirl flows, such as unsteady tip flow structures, with reasonable accuracy. Originality/value The paper presents a validated numerical model that simulates the unsteady response of the TLF to upstream perturbations in an axial fan stage. It also provides levels of instabilities in the TLV derived from the deterministic non-uniformities associated to the vane wakes.

Tip leakage flow and aeroacoustics analysis of a low-speed axial fan

2020 ◽  
Vol 98 ◽  
pp. 105700 ◽  
Author(s):  
Bo Luo ◽  
Wuli Chu ◽  
Haoguang Zhang
Keyword(s):  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Axial Fan ◽  
Low Speed ◽  
Tip Leakage

Unsteady Modelling of the Tip Clearance Flow in an Inlet Vaned, Low-Speed Axial Fan: Deterministic Interactions of Stator Wakes and Tip Vortex Structures

2009 ◽  
Author(s):  
Jesu´s Manuel Ferna´ndez Oro ◽  
Katia Mari´a Argu¨elles Di´az ◽  
Carlos Santolaria Morros ◽  
Mo´nica Galdo Vega
Keyword(s):  
Three Dimensional ◽  
Vortex Structures ◽  
Operating Conditions ◽  
Tip Vortex ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Axial Fan ◽  
Low Speed ◽  
Tip Leakage ◽  
The Impact

In last years, numerical modelling has reached a significant level of maturity in the analysis of axial turbomachinery flows. Full-unsteady, three-dimensional computations have been demonstrated as a powerful tool to characterize viscous phenomena on blade row interactions and blade passage structures. In particular, major effects have been focused on the study of deterministic fluctuations in order to quantify the impact of periodic unsteadiness on the time-averaged flow. An additional complexity concerns to the influence of the tip vortex structures on the deterministic patterns. Hence, some researchers have advanced experimental evidences on the contribution of tip leakage flow to the time-resolved distributions. Tip vortex, shedding energy at a wide range of scales, has been shown to be significant in the description of the spanwise momentum transfer and the appearance of mixing losses. Recently, the authors have investigated the impact of the tip vortex on the passage flow structures of a jet fan with symmetric blades. This work revealed valuable information about tip vortex transport in low-speed axial turbomachinery and demonstrated the ability of commercial codes to simulate three-dimensional, vortical structures with high accuracy. The present paper takes advantage of the same numerical methodology to highlight the influence of the deterministic correlations that describe the stator-rotor interaction on the tip vortex in a single-stage axial fan. Up to now, few works addressing deterministic contributions over the tip leakage flow are available in the literature, so more investigation is needed to understand the complexity of these physical mechanisms. Our contribution to the topic is based on a 3D, unsteady numerical simulation of the flow within a reduced periodic domain of the full-annulus axial stage, composed by only 3-vane and 2-blade passages. This simplification allows an enhancement of the grid density when massive parallel computations are employed. Also, comparison with experimental data measured using hot-wire anemometry is provided to validate the numerical model. The results show how the non-uniformities of the stator wake-core structure in the relative frame of reference are conditioning the tip leakage flow, addressing the influence of the operating conditions or the interrow spacing. The final objective is to provide levels of instabilities in the tip vortex derived from deterministic non-uniformities associated to vane-to-vane flow patterns, applicable in further modelling of deterministic stresses.

Effect of Active Modulation of Through-Casing Coolant Injection on Turbine Efficiency

2017 ◽  
Author(s):  
Brian M. T. Tang ◽  
Marko Bacic ◽  
Peter T. Ireland
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Total Pressure ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Turbine Efficiency ◽  
Coolant Injection ◽  
Cooling Air

This paper presents a computational investigation into the impact of cooling air injected through the stationary over-tip turbine casing on overall turbine efficiency. The high work axial flow turbine is representative of the high pressure turbine of a civil aviation turbofan engine. The effect of active modulation of the cooling air is assessed, as well as that of the injection locations. The influence of the through-casing coolant injection on the turbine blade over-tip leakage flow and the associated secondary flow features are examined. Transient (unsteady) sliding mesh simulations of a one turbine stage rotor-stator domain are performed using periodic boundary conditions. Cooling air configurations with a constant total pressure air supply, constant mass flow rate and actively controlled total pressure supply are assessed for a single geometric arrangement of cooling holes. The effects of both the mass flow rate of cooling air and the location of its injection relative to the turbine rotor blade are examined. The results show that all of the assessed cooling configurations provided a benefit to turbine row efficiency of between 0.2 and 0.4 percentage points. The passive and constant mass flow rate configurations reduced the over-tip leakage flow, but did so in an inefficient manner, with decreasing efficiency observed with increasing injection mass flow rate beyond 0.6% of the mainstream flow, despite the over-tip leakage mass flow rate continuing to reduce. By contrast, the active total pressure controlled injection provided a more efficient manner of controlling this leakage flow, as it permitted a redistribution of cooling air, allowing it to be applied in the regions close to the suction side of the blade tip which more directly reduced over-tip leakage flow rates and hence improved efficiency. Cooling air injected close to the pressure side of the rotor blade was less effective at controlling the leakage flow, and was associated with increased aerodynamic loss in the passage vortex.

Analysis of tip-leakage flow in an axial fan at varying tip-gap sizes and operating conditions

2019 ◽  
Vol 183 ◽  
pp. 107-129 ◽  
Author(s):  
Seyed Mohsen Alavi Moghadam ◽  
Matthias Meinke ◽  
Wolfgang Schröder
Keyword(s):  
Operating Conditions ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Axial Fan ◽  
Tip Leakage

Stall Inception and Development Process Due to Tip Leakage Flow in Axial Compressor Rotor Blades Row

2014 ◽  
Vol 30 (3) ◽  
pp. 307-313 ◽  
Author(s):  
R. Taghavi-Zenou ◽  
S. Abbasi ◽  
S. Eslami
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Leading Edge ◽  
Rotor Blades ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Compressor Rotor

ABSTRACTThis paper deals with tip leakage flow structure in subsonic axial compressor rotor blades row under different operating conditions. Analyses are based on flow simulation utilizing computational fluid dynamic technique. Three different circumstances at near stall condition are considered in this respect. Tip leakage flow frequency spectrum was studied through surveying instantaneous static pressure signals imposed on blades surfaces. Results at the highest flow rate, close to the stall condition, showed that the tip vortex flow fluctuates with a frequency close to the blade passing frequency. In addition, pressure signals remained unchanged with time. Moreover, equal pressure fluctuations at different passages guaranteed no peripheral disturbances. Tip leakage flow frequency decreased with reduction of the mass flow rate and its structure was changing with time. Spillage of the tip leakage flow from the blade leading edge occurred without any backflow in the trailing edge region. Consequently, various flow structures were observed within every passage between two adjacent blades. Further decrease in the mass flow rate provided conditions where the spilled flow ahead of the blade leading edge together with trailing edge backflow caused spike stall to occur. This latter phenomenon was accompanied by lower frequencies and higher amplitudes of the pressure signals. Further revolution of the rotor blade row caused the spike stall to eventuate to larger stall cells, which may be led to fully developed rotating stall.

scholarly journals On Scaling Method to Investigate High-Speed Over-Tip-Leakage Flow at Low-Speed Condition

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Hongmei Jiang ◽  
Li He ◽  
Qiang Zhang ◽  
Lipo Wang
Keyword(s):  
High Speed ◽  
Turbine Blades ◽  
Flow Distribution ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Scaling Method ◽  
Low Speed ◽  
Tip Leakage ◽  
Speed Condition

Modern high-pressure turbine blades operate at high-speed conditions. The over-tip-leakage (OTL) flow can be high-subsonic or even transonic. From the consideration of problem simplification and cost reduction, the OTL flow has been studied extensively in low-speed experiments. It has been assumed a redesigned low-speed blade profile with a matched blade loading should be sufficient to scale the high-speed OTL flow down to the low-speed condition. In this paper, the validity of this conventional scaling approach is computationally examined. The computational fluid dynamics (CFD) methodology was first validated by experimental data conducted in both high- and low-speed conditions. Detailed analyses on the OTL flows at high- and low-speed conditions indicate that, only matching the loading distribution with a redesigned blade cannot ensure the match of the aerodynamic performance at the low-speed condition with that at the high-speed condition. Specifically, the discrepancy in the peak tip leakage mass flux can be as high as 22%, and the total pressure loss at the low-speed condition is 6% higher than the high-speed case. An improved scaling method is proposed hereof. As an additional dimension variable, the tip clearance can also be “scaled” down from the high-speed to low-speed case to match the cross-tip pressure gradient between pressure and suction surfaces. The similarity in terms of the overall aerodynamic loss and local leakage flow distribution can be improved by adjusting the tip clearance, either uniformly or locally.

PIV Maps of Tip Leakage and Secondary Flow Fields on a Low-Speed Turbine Blade Cascade With Moving End Wall

2007 ◽  
Vol 130 (1) ◽  
Author(s):  
P. Palafox ◽  
M. L. G. Oldfield ◽  
J. E. LaGraff ◽  
T. V. Jones
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Field Measurements ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage ◽  
End Wall

New, detailed flow field measurements are presented for a very large low-speed cascade representative of a high-pressure turbine rotor blade with turning of 110deg and blade chord of 1.0m. Data were obtained for tip leakage and passage secondary flow at a Reynolds number of 4.0×105, based on exit velocity and blade axial chord. Tip clearance levels ranged from 0% to 1.68% of blade span (0% to 3% of blade chord). Particle image velocimetry was used to obtain flow field maps of several planes parallel to the tip surface within the tip gap, and adjacent passage flow. Vector maps were also obtained for planes normal to the tip surface in the direction of the tip leakage flow. Secondary flow was measured at planes normal to the blade exit angle at locations upstream and downstream of the trailing edge. The interaction between the tip leakage vortex and passage vortex is clearly defined, revealing the dominant effect of the tip leakage flow on the tip end-wall secondary flow. The relative motion between the casing and the blade tip was simulated using a motor-driven moving belt system. A reduction in the magnitude of the undertip flow near the end wall due to the moving wall is observed and the effect on the tip leakage vortex examined.

scholarly journals Experimental investigation of the tip leakage flow in a low-speed multistage axial compressor

2020 ◽  
Vol 103 (3) ◽  
pp. 003685042095107
Author(s):  
Jun Li ◽  
Jun Hu ◽  
Chenkai Zhang
Keyword(s):  
Static Pressure ◽  
Axial Compressor ◽  
Stereoscopic Particle Image Velocimetry ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Complex Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage ◽  
Multistage Axial Compressor

Casing pressure measurements and Stereoscopic Particle-Image Velocimetry (SPIV) measurements are used together to characterize the behavior of the rotor tip leakage flow at both the design and near-stall conditions in a low-speed multistage axial compressor. A three-dimensional Navier-Stokes solver is also performed for the multistage compressor and the prediction of tip leakage flow is compared with SPIV data and casing dynamic static pressure data. During the experiment 10 high-frequency Kulite transducers are mounted in the outer casing of the rotor 3 to investigate the complex flow near the compressor casing and Fourier analyses of the dynamic static pressure on the casing of the rotor 3 are carried out to investigate the tip leakage flow characteristics. At the same time, the two CCD cameras are arranged at the same side of the laser light sheet, which is suitable for investigating unsteady tip leakage flow in the multistage axial compressor. The SPIV measurements identify that the tip leakage flow exists in the rotor passage. The influence of tip leakage flow leads to the existence of low axial velocity region in the rotor passage and the alternating regions of positive and negative radial velocity indicates the emergence of tip leakage vortex (TLV). The trajectory of the tip leakage vortex moves from the suction surface toward the pressure surface of adjacent blade, which is aligned close to the rotor at the design point (DP). However, the tip leakage vortex becomes unstable and breaks down at the near-stall point (NS), making the vortex trajectory move upstream in the rotor passage and causing a large blockage in the middle of the passage.

Numerical Study on the Response of Tip Leakage Flow Unsteadiness to Micro Tip Injection in a Low-Speed Isolated Compressor Rotor

2007 ◽  
Author(s):  
Shaojuan Geng ◽  
Hongwu Zhang ◽  
Jingyi Chen ◽  
Weiguang Huang
Keyword(s):  
Numerical Study ◽  
The Self ◽  
Axial Position ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Low Speed ◽  
Tip Leakage ◽  
Flow Unsteadiness ◽  
Compressor Rotor ◽  
Tip Injection

A numerical study on the unsteady tip leakage flow with discrete micro tip injection from casing shroud in a low-speed isolated axial compressor rotor is presented. The main target is to clarify the flow mechanism of how the stall control measures act on the tip leakage flow typified by its self-induced unsteady flow characteristics. At operating condition near stall point, a series of calculations have been carried out for different axial position of injector and different injected mass flow rate. The computation results of flow field near rotor tip region show that under the influence of injected flow, the transient pressure distribution fluctuates along blade chord on both pressure and suction sides with respect to the relative position of injector and rotor. The pressure difference across the pressure and suction sides of compressor blade changes correspondingly, thus introduces a forced flow unsteadiness interacting with the unsteady tip leakage flow. When the injection is relatively strong and able to meet the tip leakage flow at its origination, the self-induced unsteadiness of tip leakage flow can be suppressed completely. In most cases, both frequency components of the self-induced unsteadiness and forced-induced unsteadiness are co-existing. The corresponding transient flow contours show that a local high pressure spot appears near blade pressure side, which moves downstream and shifts the tip leakage flow trajectory with less or without touching the neighboring pressure surface of the blade. Based on this understanding of discrete tip injection as force-induced flow unsteadiness, the numerical results are also analyzed to optimize the effect of injection in changing the route of tip leakage flow trajectories and therefore the chance of stability improvement of the compressor rotor.

Sign in / Sign up

Export Citation Format

Share Document