Relationship between arrangement patterns and tribological properties of copper-aluminum-graphite materials

2016 ◽  
Vol 68 (2) ◽  
pp. 170-175
Author(s):  
Fei Gao ◽  
Jia Miao ◽  
Xiaoming Han ◽  
Rong Fu ◽  
Jiguang Chen
Keyword(s):  
Friction Coefficient ◽  
High Speed ◽  
Pure Copper ◽  
Test Machine ◽  
Third Body ◽  
Content Type ◽  
Artificial Graphite ◽  
Evolution Characteristics ◽  
Copper Aluminum ◽  
Graphite Sheets

Purpose – Since the multi-component of powder metallurgy was dispersed, and each component sheared flow and tiered under the action of friction force, it was difficult to disclose the evolution characteristics of each component. Meanwhile, third body mixing with particles of each component covered on the friction surface, which further increased the difficulty of understanding evolution of each component and the corresponding third body in the friction process. To solve this problem, this paper aims to propose a mechanical assembled method which compact several component sheets in order. Design/methodology/approach – Pure copper, aluminum and artificial graphite sheets with thickness 0.5, 1 and 2 mm, respectively, were assembled into a jig by mechanical compact method. The relationship between arrangement patterns of the components and its friction coefficient was studied by using fixed speed friction test machine, the speed range from 200 to 2,000 r/min and the pressure range from 0.25 to 0.64 MPa. Findings – The testing results showed that when the distribution of same components was congregated, friction coefficient dropped from 0.6 to 0.4. While the distribution of different components was dispersed, friction coefficient dropped from 0.6 to 0.25. The friction coefficient decline was caused by performances changes of third body fluidity. The sufficiently mixed third body made third body adhesion weaker and increased third body fluidity. That provoked friction coefficient decreasing obviously at high speed. On the contrary, with the high congregation of same components, strong third body adhesion led to a rougher surface which contributed to a higher friction coefficient. Originality/value – By means of the mechanical-assembled multi-layer components to reveal the influence mechanism of every component on friction properties, will provide a new test approach for tribology.

Tribological behavior and film-forming mechanism of a polytetrafluoroethylene/polyester fabric composite

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Juan Wang ◽  
Xiongrong Huang ◽  
Wei Wang ◽  
Haosheng Han ◽  
Hongyu Duan ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
High Speed ◽  
Tribological Behavior ◽  
Elemental Content ◽  
Wear Depth ◽  
Content Type ◽  
Pet Fabric ◽  
Forming Mechanism ◽  
Fabric Composite ◽  
Film Forming

Purpose The purpose of this study is to determine the tribological behavior and wear mechanism of a polytetrafluoroethylene (PTFE)/polyester (PET) fabric composite for application as a self-lubricating liner suitable for high-speed and low-load friction conditions. Design/methodology/approach The effects of different loads and sliding speeds on the friction coefficients and wear characteristics of the composite were studied using reciprocating friction tests. Scanning electron microscopy, extended depth-of-field microscopy, and energy-dispersive X-ray spectrometry was used to analyze the worn surface morphology, wear depth and elemental content of the lubrication films, respectively. Findings The friction coefficient curves of the composites presented a long-term steady wear stage under different sliding conditions. With increasing sliding speed, the friction coefficient and wear depth of the composite slowly increased. The film-forming mechanism of the composite revealed that the PTFE/PET ply yarn on the composite surface formed complete PTFE lubrication films at the initial sliding stage. Originality/value The PTFE/PET fabric composite maintained good friction stability and high-speed adaptability, which demonstrates that the composite has broad application prospects as a highly reliable self-lubricating bearing liner with a long lifespan.

The effect of serpentine additive on energy-saving and auto-reconditioning surface layer formation

2017 ◽  
Vol 69 (2) ◽  
pp. 158-165 ◽  
Author(s):  
Xiao Wang ◽  
Junwei Wu ◽  
Xicheng Wei ◽  
Rende Liu ◽  
Qi Cao
Keyword(s):  
Surface Layer ◽  
Friction Coefficient ◽  
Mass Loss ◽  
Energy Saving ◽  
Normal Load ◽  
Lubricant Additive ◽  
Test Machine ◽  
Content Type ◽  
Saving Effect ◽  
Worn Surface

Purpose This paper aims to investigate the energy-saving effect and mechanism of serpentine as lubricant additive in the simulated condition. Design/methodology/approach An ABLT-1 bearing test machine was used for 1,350 hours and an MM-W1 three-pin-on-disk apparatus was used to investigate its anti-friction effect. The worn surface was characterized by scanning electron microscopy equipped with energy dispersive spectroscopy. Findings The results show that the energy-saving effect was improved after adding serpentine powder in oil and that both the friction coefficient and mass loss were dramatically decreased. The analysis on worn surface layer demonstrates that an auto-reconditioning surface layer was formed on the worn surface, which was responsible for the decrease in friction and wear. Originality/value The simulation test for the metal bearing was conducted over 1,350 hours using lubricant with and without serpentine powder. The addition of serpentine powder enhanced the energy-saving rate over time, stabilizing at about 13 per cent after 1,000 hours. An auto-reconditioning surface layer was formed on the surfaces of disassembled bearing lubricated with serpentine doped oil, resulting in dramatic decrease of both the friction coefficient and the mass loss. In addition to normal load and the accumulation of serpentine powder in the furrows and scratches of the deformed layer, the formation of the surface layer was possibly related to the substrate deformation induced by friction force.

Tribological behaviors of precipitates reinforced Cr-Ni-Mo-V steel lubricated by water or water-silica mixture

2018 ◽  
Vol 70 (8) ◽  
pp. 1431-1436 ◽  
Author(s):  
Shuaishuai Zhu ◽  
Baosen Zhang ◽  
Zhixin Ba ◽  
Xiangyang Mao ◽  
Weijie Fei ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
High Speed ◽  
Brake Disc ◽  
Wear Properties ◽  
Fatigue Wear ◽  
Industrial Firms ◽  
Content Type ◽  
Liquid Cell ◽  
Braking Process ◽  
Worn Surface

Purpose This paper aims to investigate the friction and wear properties of Cr-Ni-Mo-V steel against 440C stainless steel under both water and water–silica mixture lubricant. Design/methodology/approach The Cr-Ni-Mo-V steel specimens were taken from a forged steel brake disc with the process of quenching at 900°C and tempering at 600°C. The tribological testing was performed using a contact configuration of ball-on-flat with a liquid cell according to the ASTM standard. Detailed examinations on the worn surface were analyzed using a scanning electron microscope. Findings The results indicate that the friction coefficient and friction damage of the steel sliding under water–silica mixture are higher than those under water. The friction coefficient decreases with increasing load and increases with the sliding speed for the two lubricants. The mass wear rate presents a rising trend with both sliding load and speed. The wear mechanisms of the Cr-Ni-Mo-V steel sliding under the two lubricants are oxidation wear, abrasive wear and fatigue wear. Research limitations/implications Because of the chosen tribological testing approach, the research results could not describe the tribological performance of the brake disc accurately during actual braking process of the high-speed train. Therefore, researchers are encouraged to test the proposed propositions further. Originality/value This study shows that the tribology behavior of the Cr-Ni-Mo-V steel with water or water–silica mixture lubrications helps the industrial firms and academicians to work on the wear of the brake disc in rainwater or wet environment.

Estimation of rolling friction coefficients in a tribosystem using optical measurements

2018 ◽  
Vol 70 (4) ◽  
pp. 680-686
Author(s):  
Yiling Li ◽  
Yinhu Xi ◽  
Yijun Shi
Keyword(s):  
Friction Coefficient ◽  
Analytical Model ◽  
High Speed ◽  
Rolling Friction ◽  
Steel Ball ◽  
Optical Measurements ◽  
Aluminum Surface ◽  
Content Type ◽  
Rolling Friction Coefficient ◽  
Small Steel

Purpose This paper aims to present a method to measure the rolling friction coefficient in an easy and fast way. The aim is also to measure the rolling friction coefficient between a small steel ball and a cylindrical aluminum surface. Design/methodology/approach An analytical model of the tribosystem of a freely rolling ball and a cylindrical surface is established. The rolling friction coefficient is evaluated from images recorded by a high-speed camera. The coefficient between a 1.58-mm diameter steel ball and a cylindrical aluminum surface is measured. A background subtraction algorithm is used to determine the position of the small steel ball. Findings The angular positions of the ball are predicted using the analytical model, and a good agreement is found between the experimental and theoretical results. Originality/value An optical method for evaluating the rolling friction coefficient is presented, and the value of this coefficient between a small steel ball and a cylindrical aluminum surface is evaluated.

Effect of Graphite Content on the Tribological Performance of Copper-Matrix Composites Under Different Friction Speeds

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Han Xiao-Ming ◽  
Gao Fei ◽  
Su Lin-Lin ◽  
Fu Rong ◽  
Zhang En
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
High Speed ◽  
Copper Matrix ◽  
Tribological Performance ◽  
Matrix Composites ◽  
Third Body ◽  
H13 Steel ◽  
Copper Matrix Composites ◽  
The Third

The effect of graphite (Gr) content on tribological performance of copper-matrix composites against H13 steel was investigated using a pin-on-disk test in the range of 3.14–47.1 m/s. The composites with different weight fractions of Gr (up to 18%) were fabricated by powder metallurgy technique. The results showed that the friction coefficient and wear rate generally decreased with the increase in Gr content. However, the friction coefficient and wear rate differ at various speeds. At 200 and 500 r/min, the friction coefficient and wear rate kept lower with the increase in Gr content, because the third body of Cu–Al–3%Gr specimen had strong fluidity and plasticity. By contrast, the particle third body of Cu–Al–12%Gr specimen, which contained higher content of Gr, could roll easily. Increased Gr feeding to the third body was reasonable for the decreasing of friction coefficient and wear with the increasing of the amount of Gr content at the speed in the range of 1000–2000 r/min. Under the high-speed, the friction coefficient showed slight change because the friction temperature induced all the third bodies to extend and flow effortlessly without componential influence. However, wear decreased significantly because the third body possessed more metal, which favored attachment to the counter disk.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

Study on high-temperature wear and mechanism of Al-Si/graphite composites prepared by the die-casting process

2020 ◽  
Vol 72 (10) ◽  
pp. 1153-1158 ◽  
Author(s):  
Yafei Deng ◽  
Xiaotao Pan ◽  
Guoxun Zeng ◽  
Jie Liu ◽  
Sinong Xiao ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Peer Review ◽  
Die Casting ◽  
Casting Machine ◽  
Injection Pressure ◽  
Casting Process ◽  
Matrix Alloy ◽  
Content Type ◽  
The Matrix

Purpose This paper aims to improve the tribological properties of aluminum alloys and reduce their wear rate. Design/methodology/approach Carbon is placed in the model at room temperature, pour 680°C of molten aluminum into the pressure chamber, and then pressed it into the mold containing carbon felt through a die casting machine, and waited for it to cool, which used an injection pressure of 52.8 MPa and held the same pressure for 15 s. Findings The result indicated that the mechanical properties of matrix and composite are similar, and the compressive strength of the composite is only 95% of the matrix alloy. However, the composite showed a low friction coefficient, the friction coefficient of Gr/Al composite is only 0.15, which just is two-third than that of the matrix alloy. Similarly, the wear rate of the composite is less than 4% of the matrix. In addition, the composite can avoid severe wear before 200°C, but the matrix alloy only 100°C. Originality/value This material has excellent friction properties and is able to maintain this excellent performance at high temperatures. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-10-2019-0454/

Influence of ageing treatment on microstructure, mechanical properties and adhesive wear behaviour of 6063 aluminium alloy

2014 ◽  
Vol 66 (4) ◽  
pp. 520-524 ◽  
Author(s):  
Serkan Büyükdoğan ◽  
Süleyman Gündüz ◽  
Mustafa Türkmen
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
High Speed ◽  
Al Alloys ◽  
Wear Behaviour ◽  
Al Alloy ◽  
Strain Ageing ◽  
Content Type ◽  
Static Strain ◽  
Structural Applications

Purpose – The paper aims to provide new observations about static strain ageing in aluminium (Al) alloys which are widely used in structural applications. Design/methodology/approach – The present work aims to provide theoretical and practical information to industries or researchers who may be interested in the effect of static strain ageing on mechanical properties of Al alloys. The data are sorted into the following sections: introduction, materials and experimental procedure, results and discussion and conclusions. Findings – Tensile strength, proof strength (0.2 per cent) and percentage elongation measurement were used to investigate the effect of strain ageing on the mechanical properties. Wear tests were performed by sliding the pin specimens, which were prepared from as-received, solution heat-treated, deformed and undeformed specimens after ageing, on high-speed tool steel (64 HRC). It is concluded that the variations in ageing time improved the strength and wear resistance of the 6063 Al alloy; however, a plastically deformed solution-treated alloy has higher strength and wear resistance than undeformed specimens for different ageing times at 180°C. Practical implications – A very useful source of information for industries using or planning to produce Al alloys. Originality/value – This paper fulfils an identified resource need and offers practical help to the industries.

Impacts of high-speed railway on the industrial pollution emissions in China

Kybernetes ◽  
2020 ◽  
Vol 49 (11) ◽  
pp. 2713-2735 ◽  
Author(s):  
Xiaomin Fan ◽  
Yingzhi Xu ◽  
Yongqing Nan ◽  
Baoli Li ◽  
Haiya Cai
Keyword(s):  
Environmental Effects ◽  
Industrial Pollution ◽  
High Speed ◽  
Assessment Method ◽  
Economic Effects ◽  
High Speed Railway ◽  
Central Cities ◽  
Content Type ◽  
Pollution Emissions ◽  
The Impact

Purpose The purpose of this paper is to analyse the impact of high-speed railway (HSR) on industrial pollution emissions using the data for 285 prefecture-level cities in China from 2004 to 2016. Design/methodology/approach The research method used in this paper is the multi-period difference-in-differences (DID) model, which is an effective policy effect assessment method. To further address the issue of endogeneity, the DID integrated with the propensity score matching (PSM-DID) approach is employed to eliminate the potential self-selection bias. Findings The results show that the HSR has significantly reduced industrial pollution emissions, which is validated by several robustness tests. Compared with peripheral cities, HSR exerts a greater impact on industrial pollution emissions in central cities. In addition, the mechanism test reveals that the optimised allocation of inter-city industries is an important channel for HSR to mitigate industrial pollution emissions, and this is closely related to the location of HSR stations. Originality/value Previous studies have paid more attention to evaluating the economic effects of HSR, however, most of these studies overlook its environmental effects. Consequently, the impact of HSR on industrial pollution emissions is led by using multi-period DID models in this paper, in which the environmental effects are measured. The results of this paper can provide a reference for the pollution reduction policies and also the coordinated development of economic growth and environmental quality.

Comparison of the reluctance laminated and solid rotor synchronous machine operating at high temperatures

2019 ◽  
Vol 38 (4) ◽  
pp. 1111-1119 ◽  
Author(s):  
Marcin Lefik ◽  
Krzysztof Komeza ◽  
Ewa Napieralska-Juszczak ◽  
Daniel Roger ◽  
Piotr Andrzej Napieralski
Keyword(s):  
High Speed ◽  
Design Methodology ◽  
Three Dimensional ◽  
Synchronous Machine ◽  
Point Of View ◽  
Heat Sources ◽  
Model Calculations ◽  
Content Type ◽  
Thermal Phenomenon ◽  
Practical Implications

Purpose The purpose of this paper is to present a comparison between reluctance synchronous machine-enabling work at high internal temperature (HT° machine) with laminated and solid rotor. Design/methodology/approach To obtain heat sources for the thermal model, calculations of the electromagnetic field were made using the Opera 3D program including effect of rotation and the resulting eddy current losses. To analyse the thermal phenomenon, the 3D coupled thermal-fluid (CFD) model is used. Findings The presented results show clearly that laminated construction is much better from a point of view of efficiency and temperature. However, solid construction can be interesting for high speed machines due to their mechanical robustness. Research limitations/implications The main problem, despite the use of parallel calculations, is the long calculation time. Practical implications The obtained simulation and experimental results show the possibility of building a machine operating at a much higher ambient temperature than it was previously produced for example in the vicinity of the aircraft turbines. Originality/value The paper presents the application of fully three-dimensional coupled electromagnetic and thermal analysis of new machine constructions designed for elevated temperature.

Sign in / Sign up

Export Citation Format

Share Document