Air-Bearing Design Towards Super Stable Head-Disk Interface

2006 ◽  
Author(s):  
Bo Liu ◽  
MingSheng Zhang ◽  
Yijun Man ◽  
Shengkai Yu ◽  
Gonzaga Leonard ◽  
...  
Keyword(s):  
Air Bearing ◽  
Head Disk Interface ◽  
Disk Interface ◽  
Bearing Design

Air-Bearing Design Towards Highly Stable Head–Disk Interface at Ultralow Flying Height

2007 ◽  
Vol 43 (2) ◽  
pp. 715-720 ◽  
Author(s):  
Bo Liu ◽  
Shengkai Yu ◽  
Mingsheng Zhang ◽  
Leonard Gonzaga ◽  
Hui Li ◽  
...  
Keyword(s):  
Flying Height ◽  
Air Bearing ◽  
Head Disk Interface ◽  
Disk Interface ◽  
Bearing Design

Partial Contact Head-Disk Interface With Thermal Protrusion

2009 ◽  
Author(s):  
Du Chen ◽  
David B. Bogy
Keyword(s):  
Vibration Amplitude ◽  
Dynamic Performance ◽  
Flying Height ◽  
Air Bearing ◽  
Head Disk Interface ◽  
Dynamic Simulations ◽  
Disk Interface ◽  
Partial Contact ◽  
Thermal Protrusion ◽  
Bearing Design

A new partial contact head disk interface (HDI) with thermal protrusion is proposed for magnetic recording with densities of 1 Tbit/in2 and above. This HDI has the advantage of maintaining light contact between the slider and the disk, so that both the bouncing vibration amplitude and the contact force are small compared with a traditional partial contact HDI. The slider’s dynamic simulations are carried out to analyze the effect of various factors within the HDI on the slider’s dynamic performance, including the friction and adhesion between the slider and the disk, the track profile morphology of the disk and the air bearing design. It is found that the bouncing vibration amplitude can be reduced to the level of the flying height modulation (FHM) of a non-contact air bearing slider without thermal protrusion.

Wear Characteristics of Padded Air Bearing Sliders During a Contact Take-Off Process

1999 ◽  
Vol 122 (3) ◽  
pp. 628-632 ◽  
Author(s):  
Yong Hu
Keyword(s):  
New Technologies ◽  
Interface Roughness ◽  
Wear Volume ◽  
Air Bearing ◽  
Wear Factor ◽  
Wear Characteristics ◽  
Disk Interface ◽  
Force Profile ◽  
Bearing Design ◽  
Wear Law

The pressing and challenging demand for resolving the stiction/glide-height conflict, driven by today’s ever decreasing head/disk spacing, forces us to constantly search for new technologies. One of them is padding the slider’s air bearing surface. Although the padded air bearing sliders can significantly reduce the stiction, the wear of these landing pads becomes a central issue. This paper attempts to analytically predict the wear characteristics of the landing pads during a contact take-off process. A wear factor derived from the adhesive wear law is employed to measure the wear extent of the landing pads. The contact force profile and wear factor of each pad are calculated through the partial contact air bearing simulation of a slider’s take-off process. It is found that the rear pad wears an order magnitude more than the leading pads. The wear volume of the rear pad increases exponentially with pad height, interface roughness and altitude. Raising the leading pads alone slightly reduces the wear of the rear pad. Placing the rear pad away from the slider’s trailing edge, however, substantially alleviates the wear of the rear pad. Finally, a lightly textured pad/disk interface decreases the pads’ wear to a minimum value for a given padded air bearing design. [S0742-4787(00)01903-2]

scholarly journals Parametric Investigations at the Head-Disk Interface of Thermal Fly-Height Control Sliders in Contact

2012 ◽  
Vol 2012 ◽  
pp. 1-11 ◽  
Author(s):  
Sripathi V. Canchi ◽  
David B. Bogy ◽  
Run-Han Wang ◽  
Aravind N. Murthy
Keyword(s):  
Hard Disk Drives ◽  
Air Bearing ◽  
Head Disk Interface ◽  
Bearing Surface ◽  
Surface Design ◽  
Disk Interface ◽  
Height Control ◽  
Experimental Findings ◽  
And Control ◽  
Fly Height

Accurate touchdown power detection is a prerequisite for read-write head-to-disk spacing calibration and control in current hard disk drives, which use the thermal fly-height control slider technology. The slider air bearing surface and head gimbal assembly design have a significant influence on the touchdown behavior, and this paper reports experimental findings to help understand the touchdown process. The dominant modes/frequencies of excitation at touchdown can be significantly different leading to very different touchdown signatures. The pressure under the slider at touchdown and hence the thermal fly-height control efficiency as well as the propensity for lubricant pickup show correlation with touchdown behavior which may be used as metrics for designing sliders with good touchdown behavior. Experiments are devised to measure friction at the head-disk interface of a thermal fly-height control slider actuated into contact. Parametric investigations on the effect of disk roughness, disk lubricant parameters, and air bearing surface design on the friction at the head-disk interface and slider burnishing/wear are conducted and reported.

Boundary Effect on Particle Motion in the Head Disk Interface

2007 ◽  
Author(s):  
Nan Liu ◽  
David B. Bogy
Keyword(s):  
Drag Force ◽  
Particle Motion ◽  
Boundary Effect ◽  
Hard Disk Drives ◽  
Areal Density ◽  
Air Bearing ◽  
Disk Drives ◽  
Head Disk Interface ◽  
Bearing Surface ◽  
Disk Interface

Simulation of particle motion in the Head Disk Interface (HDI) helps to understand the contamination process on a slider, which is critical for achieving higher areal density of hard disk drives. In this study, the boundary effect—the presence of the slider and disk—on particle motion in the HDI is investigated. A correction factor to account for this effect is incorporated into the drag force formula for particles in a flow. A contamination criterion is provided to determine when a particle will contaminate a slider. The contamination profile on a specific Air Bearing Surface is obtained, which compares well with experiments.

Sign in / Sign up

Export Citation Format

Share Document