Research on Anti-Cracking Design Method of Steel-Concrete Composite Beams in Negative Moment Zone

2019 ◽  
Author(s):  
Yaoyi Dong ◽  
Yue Xu
Keyword(s):  
Design Method ◽  
Composite Beams ◽  
Negative Moment

scholarly journals Lateral distortional buckling of cellular composite-beams

2018 ◽  
Vol 11 (2) ◽  
pp. 331-356 ◽  
Author(s):  
A. D. PIASSI ◽  
J. V. DIAS ◽  
A. F. G. CALENZANI ◽  
F. C. C. MENANDRO
Keyword(s):  
Flexural Rigidity ◽  
Lateral Displacement ◽  
Limit State ◽  
Composite Beams ◽  
Bottom Flange ◽  
Distortional Buckling ◽  
Critical Moment ◽  
Negative Moment ◽  
Resistant Moment ◽  
Negative Bending

Abstract In the region of negative bending moments of continuous and semi-continuous steel and concrete composite beams, the inferior portion of the steel section is subjected to compression while the top flange is restricted by the slab, which may cause a global instability limit state know as lateral distortional buckling (LDB) characterized by a lateral displacement and rotation of the bottom flange with a distortion of the section’s web when it doesn’t have enough flexural rigidity. The ABNT NBR 8800:2008 provides an approximate procedure for the verification of this limit state, in which the resistant moment to LDB is obtained from the elastic critical moment in the negative moment region. One of the essential parameters for the evaluation of the critical moment is the composite beam’s rotational rigidity. This procedure is restricted only to to steel and concrete composite beams with sections that have plane webs. In this paper, an equation for the calculation of the rotational rigidity of cellular sections was developed in order to determine the LDB elastic critical moment. The formulation was verified by numerical analyses performed in ANSYS and its efficiency was confirmed. Finally, the procedure described in ABNT NBR 8800:2008 for the calculation of the critical LDB moment was expanded to composite beams with cellular sections in a numerical example with the appropriate modifications in geometric properties and rotational rigidity.

Flexural Bearing Capacity Research of Composite Beams with Edge Constraint Component

2013 ◽  
Vol 639-640 ◽  
pp. 807-811
Author(s):  
Yang Wang ◽  
Tian Li
Keyword(s):  
Bearing Capacity ◽  
Steel Structure ◽  
Composite Beams ◽  
Deformation And Failure ◽  
Finite Element Software ◽  
Composite Frame ◽  
Negative Moment ◽  
Flexural Bearing Capacity ◽  
Simulation Results ◽  
Current Code

To investigate the flexural bearing capacity in negative moment region of composite beams，we examined different ends constraint components. The modeling of the beam ends connected framework has been done by the finite element software ANSYS. The concrete thickness, slab reinforcement ratio and different component at the edge of the composite framework in the negative moment region are taken into account. The performance during the process of deformation and failure are got by nonlinear analysis. The flexural bearing capacity was reported, with the negative moment region of the composite frame beam, it revealed great differences when the beams are different component. Simulation results show that the concrete thickness take the biggest influence on bearing capacity. The results showed the behaviors of the composite frame beams are different with positive moment region, and calculation based on current code for design of steel structure (GB50017-2003) would be a big deviation.

The Fatigue Behavior of Negative Moment Regions of Continuous Composite Beams at Low Temperatures

1975 ◽  
Vol 2 (1) ◽  
pp. 98-115
Author(s):  
A. E. Long ◽  
K. Van Dalen ◽  
P. Csagoly
Keyword(s):  
Fatigue Behavior ◽  
Bending Moment ◽  
Composite Beams ◽  
Horizontal Shear ◽  
Shear Connectors ◽  
Significant Difference ◽  
Show Evidence ◽  
Negative Moment ◽  
Central Support ◽  
Push Out

The fatigue behavior of the negative moment region of continuous steel–concrete composite beams under Canadian temperature conditions was studied. Tests were conducted on three 26 ft 0 in. (7.92 m) long beams, continuous over a central support, and on 11 conventional push-out specimens. These were supplemented by a theoretical study of the internal forces in the beams using an iterative method of analysis.The close agreement between measured and theoretical strains and deflections indicated that good interaction was achieved throughout the length of the beams. The beams sustained 500 000 cycles of loading with no serious deterioration of composite action. The pattern of stud failures was consistent from beam to beam and reflected closely the calculated distribution of horizontal shear force at the steel–concrete interface. Stud shear connectors in the negative moment region where the slab had cracked in tension were found to be slightly less effective than studs in the positive bending moment regions.Neither the detailed study of individual connectors in the beams nor the results of the push-out tests show evidence of a reduction in the fatigue life of studs at −20 °F (−29 °C) relative to room temperature. The beams also exhibited no significant difference in their overall performance at these two temperatures.

A Simplified Design Method for Semi-Continuous Composite Beams

2008 ◽  
Vol 8 (24) ◽  
pp. 4533-4542
Author(s):  
M. Titoum ◽  
B. Achour ◽  
M. Tehami ◽  
A. Benanane
Keyword(s):  
Design Method ◽  
Composite Beams ◽  
Simplified Design Method

Research on Key Issues in Design of Outer-Plated Steel-Concrete Continuous Composite Beams

2012 ◽  
Vol 166-169 ◽  
pp. 414-419
Author(s):  
Li Hua Chen ◽  
Fei Xiao ◽  
Qi Liang Jin
Keyword(s):  
Composite Beam ◽  
Bending Moment ◽  
Longitudinal Shear ◽  
Structural Features ◽  
Composite Beams ◽  
Steel Beam ◽  
Negative Moment ◽  
Key Issues ◽  
Negative Bending ◽  
The Moment

Based on the theoretical analysis and testing results, some key issues in design of outer-plated steel-concrete continuous composite beams are discussed. The influence of the form of steel beam upper flange on the behavior of composite beam is analyzed. The requirements about longitudinal reinforcement strength in the concrete flange of the negative moment region are given. It is suggested that the moment-shear interaction should be neglected when calculating the flexural capacity of outer-plated steel-concrete composite beams under negative bending moment. The behavior of longitudinal shear resistance at the interface between the concrete flange and web of composite beam is studied, and the related calculating formula is put forward based on the structural features of the composite beam.

scholarly journals Fire Resistance of Steel Composite Beams without Fire Protection

2020 ◽  
Vol 20 (5) ◽  
pp. 83-89
Author(s):  
Jaekwon Ahn ◽  
Inhwan Yeo ◽  
Gyuhwan Cho ◽  
Kyujae Hwang
Keyword(s):  
Fire Resistance ◽  
Design Method ◽  
Load Ratio ◽  
Composite Beams ◽  
Building Structures ◽  
Fire Exposure ◽  
Standard Fire ◽  
Steel Composite ◽  
Fire Design ◽  
Exposure Conditions

In this study, the fire resistance of steel composite beams typically used in building structures was investigated through standard fire and loading tests. For the tests, fire-exposure conditions depending on the steel section shape and load ratio applied to the beams were considered as the test parameters. Based on the test results, the applicability of fire design methods for composite beams recommended in current domestic and overseas fire design codes was analyzed. The results indicate that the current temperature-based design method and reduced flexural capacity method specified by the American Institute of Steel Construction may lead to the conservative fire design of steel composite beams owing to the underestimation of the effects of the fire-exposure conditions and load ratios.

Analysis of Bearing Capacity of Steel-High Strength Concrete Composite Beams

2013 ◽  
Vol 838-841 ◽  
pp. 661-664
Author(s):  
Liang Li Xiao ◽  
Ming Yang Pan ◽  
Jian Wei Han
Keyword(s):  
Bearing Capacity ◽  
High Strength Concrete ◽  
Influence Factors ◽  
High Strength ◽  
Composite Beams ◽  
Finite Element Program ◽  
Strength Concrete ◽  
Element Program ◽  
Negative Moment ◽  
Negative Bending

It is very crucial to analyze the flexural bearing capacity of the steel-high strength concrete composite beams, but the combination on the flange of steel beam and their bearing capacity is limited with certain inevitability,in addition, in the negative bending regions of continuous composite beams, with the constant increase of load, the process of the whole structure will cause damages in the negative moment region. In order to avoid this kind of damages, we must use general finite element program ANSYS to analyze thebearing capacity of the steel and high strength concrete composite beams. Besides further studying the influence factors of bearing capacity, and ensuring the safety of our engineering performance can be in favor of the engineering structure.

Sign in / Sign up

Export Citation Format

Share Document