Research on Key Issues in Design of Outer-Plated Steel-Concrete Continuous Composite Beams

2012 ◽  
Vol 166-169 ◽  
pp. 414-419
Author(s):  
Li Hua Chen ◽  
Fei Xiao ◽  
Qi Liang Jin
Keyword(s):  
Composite Beam ◽  
Bending Moment ◽  
Longitudinal Shear ◽  
Structural Features ◽  
Composite Beams ◽  
Steel Beam ◽  
Negative Moment ◽  
Key Issues ◽  
Negative Bending ◽  
The Moment

Based on the theoretical analysis and testing results, some key issues in design of outer-plated steel-concrete continuous composite beams are discussed. The influence of the form of steel beam upper flange on the behavior of composite beam is analyzed. The requirements about longitudinal reinforcement strength in the concrete flange of the negative moment region are given. It is suggested that the moment-shear interaction should be neglected when calculating the flexural capacity of outer-plated steel-concrete composite beams under negative bending moment. The behavior of longitudinal shear resistance at the interface between the concrete flange and web of composite beam is studied, and the related calculating formula is put forward based on the structural features of the composite beam.

Study on the Crack in Concrete Flange of Outer-Plated Steel-Concrete Continuous Composite Beams

2012 ◽  
Vol 166-169 ◽  
pp. 1023-1028 ◽  
Author(s):  
Li Hua Chen ◽  
Qi Liang Jin ◽  
Haiyu Si
Keyword(s):  
Crack Width ◽  
Static Load ◽  
Bending Moment ◽  
Structural Features ◽  
Composite Beams ◽  
Test Results ◽  
Load Tests ◽  
Reversed Loading ◽  
Negative Bending ◽  
Stress Block

Static load tests were conducted on two reversed-loading simply supported and two continuous outer-plated steel-concrete composite beams to study the formation and development of cracks in such beams under negative bending moment. The test results show that based on the plane section assumption, it is an effective and economical method to calculate the cracking moment of the composite beams assuming a rectangular stress block for concrete in tension zone. Considering the structural features of outer-plated steel-concrete composite beams, the formula for calculating crack width of concrete flange of outer-plated steel-concrete composite beams is discussed and presented, and the calculated values of crack width agree well with the experimental results.

scholarly journals Experimental Study on Fatigue Performance of Negative Bending Moment of Steel-Concrete Continuous Composite Box Girder

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Pu Gao ◽  
Kuan Li ◽  
Yuanxun Zheng
Keyword(s):  
Concrete Slab ◽  
Bending Moment ◽  
Composite Beams ◽  
Fatigue Tests ◽  
Reinforcement Ratio ◽  
Fatigue Performance ◽  
Fatigue Load ◽  
Shear Connection ◽  
Negative Moment ◽  
Negative Bending

The experimental work presents results on the fatigue performance of composite beams in the negative moment region and the changes of stiffness and deformation of composite beams under repeated loads; fatigue tests were carried out on two double-layer composite beams. The fatigue performance of composite beams with different reinforcement ratios under complete shear connection and the variation of deflection, strain of the reinforcement, strain of steel beam, and crack growth under fatigue load were obtained. The results showed that the fatigue resistance performance of concrete slab with low reinforcement ratio was much lower than that of concrete slab with high reinforcement ratio whereas, under the fatigue load, the stress of the welding nail in the negative moment region was small and the slip was almost negligible. The degradation of stiffness and the development of cracks were mainly due to the degradation of bond-slip between the concrete and reinforcement. The fatigue failure mode was the fracture of the upper reinforcement in negative moment region. The results obtained in this study are helpful in the design of composite beam.

scholarly journals Experimental and Numerical Studies on the Negative Flexural Behavior of Steel-UHPC Composite Beams

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Xinhua Liu ◽  
Jianren Zhang ◽  
Zihan Cheng ◽  
Meng Ye
Keyword(s):  
Crack Width ◽  
Bending Moment ◽  
Composite Beams ◽  
Flexural Behavior ◽  
Element Analysis ◽  
Conventional Concrete ◽  
Bond Slip ◽  
Cracking Performance ◽  
Negative Moment ◽  
Negative Bending

The cracking of concrete in the negative moment region for a composite beam subjected to a negative bending moment reduces the beam’s strength and stiffness. To improve the cracking performance of composite beams, this paper presents an experimental investigation on applying ultrahigh-performance concrete (UHPC) instead of conventional concrete. Three steel-UHPC composite beams with different forms of joints were designed and tested through a unique rotation angle loading method using a spring displacement control testing setup. The crack distribution, rotation versus crack width, load versus spring displacement, and strains in the UHPC slab and steel girders were measured and studied. Nonlinear finite element analysis using ABAQUS based on the damaged plasticity model of concrete was carried out for comparison with the test results. The experimental and numerical results showed that the use of a UHPC slab can enhance the cracking performance of composite beams. Considering the convenience of construction, a reasonable joint form was suggested, and the appropriate UHPC longitudinal laying length in the negative moment region was proposed to be 0.1 L. Furthermore, a simplified formula for calculating the UHPC crack width was developed based on bond-slip theory.

COMPARATIVE STUDY ON THE BENDING PROPERTIES FOR TWO TYPES OF COMPOSITE BEAMS

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Xian Liang ◽  
Shujin Duan ◽  
Runming Niu ◽  
Fang Li
Keyword(s):  
Composite Beam ◽  
Concrete Slab ◽  
Process Analysis ◽  
Bending Moment ◽  
Composite Beams ◽  
Bending Properties ◽  
Laminated Beam ◽  
Whole Process ◽  
The Difference ◽  
Negative Bending

The difference between the steel and concrete composite-laminated action beam and the double steel and concrete composite action beam is in the connection of the top concrete slab and the steel top flange. The bending properties about the composite-laminated beam and the double composite beam in the negative flexural region are investigated in this paper. The relation of the cross section bending moment-curvature for the two types of composite beams under the action of negative bending moment are drawn by the whole process analysis method, and then the corresponding cracking moment, elastic ultimate bending moment and plastic ultimate bending moment are obtained. The analysis results have a good agreement with test data. Although the sectional bending stiffness and bending-carrying capacity of the composite-laminated beam and the double composite beam are comparable in the elastic state, the crack resistance of the composite-laminated beam is much better than that of the double composite beam.

Model Test of Steel-Concrete Composite Beam Deck under Negative Moment

2021 ◽  
Vol 871 ◽  
pp. 340-348
Author(s):  
Rui Rong ◽  
Yu Hui Shan ◽  
Li Zhao ◽  
Bao Qun Wang
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Model Test ◽  
Composite Beam ◽  
Bending Moment ◽  
Cable Stayed Bridge ◽  
Composite Girder ◽  
Force Transfer ◽  
Negative Moment ◽  
Negative Bending

In order to understand the mechanical properties and force transfer law of steel-concrete composite beam deck under negative bending moment, and further guide the design. Based on a steel-concrete composite girder cable-stayed bridge, the model test of the mechanical behavior of the steel-concrete composite girder deck under the action of negative moment was carried out. The characteristics of mechanical failure and mechanical properties were analyzed.

scholarly journals Longitudinal shear capacity of the slabs of composite beams

1976 ◽  
Vol 3 (4) ◽  
pp. 514-522 ◽  
Author(s):  
M. N. El-Ghazzi ◽  
H. Robinson ◽  
I. A. S. Elkholy
Keyword(s):  
Composite Beam ◽  
Shear Failure ◽  
Concrete Slab ◽  
Compressive Force ◽  
Longitudinal Shear ◽  
Composite Beams ◽  
Shear Capacity ◽  
Slab Width ◽  
Two Parameters ◽  
Concrete Elements

The longitudinal shear failure of the slab of composite beams is constrained to occur at a predetermined shear surface. A method for calculating the longitudinal shear capacity of the slab of simply-supported steel–concrete composite beams is presented. The method is based on analyzing the stresses at failure of the concrete elements located at the slab shear surface.A design chart based on estimating the transverse normal stress required within the concrete slab to achieve the full ultimate flexural capacity of the composite beam is proposed. Alternatively, using elastic–plastic stress distribution across the concrete slab, the longitudinal compressive force due to bending and hence the applied moment can be predicted for any longitudinal shear capacity of the slab. The proposed design and analysis when compared to previous tests and analysis showed good agreement.The slab width and the shear span of the composite beam are found to be two important parameters which cannot be neglected when estimating the longitudinal shear capacity of the slab. These two parameters have been neglected in the empirical solutions previously adopted.

Monotonic and fatigue assessment of steel-concrete composite beams strengthened with externally post-tensioned tendons

2018 ◽  
Author(s):  
◽  
Ayman Elzohairy
Keyword(s):  
Numerical Model ◽  
Composite Beam ◽  
Composite Beams ◽  
Fatigue Tests ◽  
Flexural Behavior ◽  
Bending Test ◽  
Steel Beam ◽  
Premature Failure ◽  
Post Tensioning ◽  
Post Tensioned

[ACCESS RESTRICTED TO THE UNIVERSITY OF MISSOURI AT AUTHOR'S REQUEST.] The steel-concrete composite beam represents a structural system widely employed in both buildings and girder bridges. The coupling between steel beams and concrete flanges assures both economic and structural benefits because of quick construction of steel structures and large increase in stiffness due to the presence of concrete. Strengthening with external post-tensioning (PT) force is particularly effective and economical for long-span steel-concrete composite beams and has been employed with great success to increase the bending and shear resistance and correct excessive deflections. Applying external PT force to the steel-concrete composite beam is considered an active strengthening technique that can create permanent internal straining action in the beam which is opposite to the existing straining action due to the applied service loads. The most benefits of using this system of strengthening are an elastic performance to higher loads, higher ultimate capacity, and reduction in deformation under the applied loads. Under service loads, bridge superstructures are subjected to cyclic loads which may cause a premature failure due to fatigue. Therefore, fatigue testing is critical to evaluate existing design methods of steel-concrete composite beams. ... This research presents static and fatigue tests on four steel-concrete composite specimens to evaluate the effect of externally post-tensioned tendons on the ultimate strength and fatigue behavior of composite beams. Fatigue tests are conducted to a million cycles under a four-point bending test. In addition, final static tests are performed on fatigued specimens to evaluate the residual strength of the strengthened specimen. A numerical model is described to predict the fatigue response of the composite beam by considering the fatigue damage in the concrete flange. The accuracy of the developed numerical model is validated using the existing test data. The static test results indicate that the external post-tensioning force improves the flexural behavior of the strengthened specimen by increasing the beam capacity and reducing the tensile stress in the bottom flange of the steel beam. The fatigue results demonstrate that the external post-tensioning significantly decreases the strains in the shear connectors, concrete flange, and steel beam. The tendons demonstrated an excellent fatigue performance, with no indication of distress at the anchors.

scholarly journals Lateral distortional buckling of cellular composite-beams

2018 ◽  
Vol 11 (2) ◽  
pp. 331-356 ◽  
Author(s):  
A. D. PIASSI ◽  
J. V. DIAS ◽  
A. F. G. CALENZANI ◽  
F. C. C. MENANDRO
Keyword(s):  
Flexural Rigidity ◽  
Lateral Displacement ◽  
Limit State ◽  
Composite Beams ◽  
Bottom Flange ◽  
Distortional Buckling ◽  
Critical Moment ◽  
Negative Moment ◽  
Resistant Moment ◽  
Negative Bending

Abstract In the region of negative bending moments of continuous and semi-continuous steel and concrete composite beams, the inferior portion of the steel section is subjected to compression while the top flange is restricted by the slab, which may cause a global instability limit state know as lateral distortional buckling (LDB) characterized by a lateral displacement and rotation of the bottom flange with a distortion of the section’s web when it doesn’t have enough flexural rigidity. The ABNT NBR 8800:2008 provides an approximate procedure for the verification of this limit state, in which the resistant moment to LDB is obtained from the elastic critical moment in the negative moment region. One of the essential parameters for the evaluation of the critical moment is the composite beam’s rotational rigidity. This procedure is restricted only to to steel and concrete composite beams with sections that have plane webs. In this paper, an equation for the calculation of the rotational rigidity of cellular sections was developed in order to determine the LDB elastic critical moment. The formulation was verified by numerical analyses performed in ANSYS and its efficiency was confirmed. Finally, the procedure described in ABNT NBR 8800:2008 for the calculation of the critical LDB moment was expanded to composite beams with cellular sections in a numerical example with the appropriate modifications in geometric properties and rotational rigidity.

The Fatigue Behavior of Negative Moment Regions of Continuous Composite Beams at Low Temperatures

1975 ◽  
Vol 2 (1) ◽  
pp. 98-115
Author(s):  
A. E. Long ◽  
K. Van Dalen ◽  
P. Csagoly
Keyword(s):  
Fatigue Behavior ◽  
Bending Moment ◽  
Composite Beams ◽  
Horizontal Shear ◽  
Shear Connectors ◽  
Significant Difference ◽  
Show Evidence ◽  
Negative Moment ◽  
Central Support ◽  
Push Out

The fatigue behavior of the negative moment region of continuous steel–concrete composite beams under Canadian temperature conditions was studied. Tests were conducted on three 26 ft 0 in. (7.92 m) long beams, continuous over a central support, and on 11 conventional push-out specimens. These were supplemented by a theoretical study of the internal forces in the beams using an iterative method of analysis.The close agreement between measured and theoretical strains and deflections indicated that good interaction was achieved throughout the length of the beams. The beams sustained 500 000 cycles of loading with no serious deterioration of composite action. The pattern of stud failures was consistent from beam to beam and reflected closely the calculated distribution of horizontal shear force at the steel–concrete interface. Stud shear connectors in the negative moment region where the slab had cracked in tension were found to be slightly less effective than studs in the positive bending moment regions.Neither the detailed study of individual connectors in the beams nor the results of the push-out tests show evidence of a reduction in the fatigue life of studs at −20 °F (−29 °C) relative to room temperature. The beams also exhibited no significant difference in their overall performance at these two temperatures.

Sign in / Sign up

Export Citation Format

Share Document