Visibility-Culling-Based Geometric Rendering of Large-Scale Particle Data

Author(s):  
Huawei Wang ◽  
Li Xiao ◽  
Yi Cao ◽  
Zhiwei Ai ◽  
Pingjun Xu
Author(s):  
Christopher Pagano ◽  
Flavia Tauro ◽  
Salvatore Grimaldi ◽  
Maurizio Porfiri

Large scale particle image velocimetry (LSPIV) is a nonintrusive environmental monitoring methodology that allows for continuous characterization of surface flows in natural catchments. Despite its promise, the implementation of LSPIV in natural environments is limited to areas accessible to human operators. In this work, we propose a novel experimental configuration that allows for unsupervised LSPIV over large water bodies. Specifically, we design, develop, and characterize a lightweight, low cost, and stable quadricopter hosting a digital acquisition system. An active gimbal maintains the camera lens orthogonal to the water surface, thus preventing severe image distortions. Field experiments are performed to characterize the vehicle and assess the feasibility of the approach. We demonstrate that the quadricopter can hover above an area of 1×1m2 for 4–5 minutes with a payload of 500g. Further, LSPIV measurements on a natural stream confirm that the methodology can be reliably used for surface flow studies.


2017 ◽  
Vol 814 ◽  
pp. 592-613 ◽  
Author(s):  
Andras Nemes ◽  
Teja Dasari ◽  
Jiarong Hong ◽  
Michele Guala ◽  
Filippo Coletti

We report on optical field measurements of snow settling in atmospheric turbulence at $Re_{\unicode[STIX]{x1D706}}=940$. It is found that the snowflakes exhibit hallmark features of inertial particles in turbulence. The snow motion is analysed in both Eulerian and Lagrangian frameworks by large-scale particle imaging, while sonic anemometry is used to characterize the flow field. Additionally, the snowflake size and morphology are assessed by digital in-line holography. The low volume fraction and mass loading imply a one-way interaction with the turbulent air. Acceleration probability density functions show wide exponential tails consistent with laboratory and numerical studies of homogeneous isotropic turbulence. Invoking the assumption that the particle acceleration has a stronger dependence on the Stokes number than on the specific features of the turbulence (e.g. precise Reynolds number and large-scale anisotropy), we make inferences on the snowflakes’ aerodynamic response time. In particular, we observe that their acceleration distribution is consistent with that of particles of Stokes number in the range $St=0.1{-}0.4$ based on the Kolmogorov time scale. The still-air terminal velocities estimated for the resulting range of aerodynamic response times are significantly smaller than the measured snow particle fall speed. This is interpreted as a manifestation of settling enhancement by turbulence, which is observed here for the first time in a natural setting.


Hydrology ◽  
2019 ◽  
Vol 6 (1) ◽  
pp. 27 ◽  
Author(s):  
Mahmood Al-mamari ◽  
Sameh Kantoush ◽  
Sohei Kobayashi ◽  
Tetsuya Sumi ◽  
Mohamed Saber

Flash floods in wadi systems discharge large volumes of water to either the sea or the desert areas after high-intensity rainfall events. Recently, wadi flash floods have frequently occurred in arid regions and caused damage to roads, houses, and properties. Therefore, monitoring and quantifying these events by accurately measuring wadi discharge has become important for the installation of mitigation structures and early warning systems. In this study, image-based methods were used to measure surface flow velocities during a wadi flash flood in 2018 to test the usefulness of large-scale particle image velocimetry (LSPIV) and space–time image velocimetry (STIV) techniques for the estimation of wadi discharge. The results, which indicated the positive performance of the image-based methods, strengthened our hypothesis that the application of LSPIV and STIV techniques is appropriate for the analysis of wadi flash flood velocities. STIV is suitable for unidirectional flow velocity and LSPIV is reliable and stable for two-dimensional measurement along the wadi channel, the direction of flow pattern which varies with time.


Author(s):  
Seung J. Rhee ◽  
Kosuke Ishii

Failure Mode and Effect Analysis (FMEA) is a design tool that helps designers identify risks. The traditional FMEA involves ambiguity with the definition of risk priority number: the product of occurrence, detection difficulty, and severity subjectively measured in a 1 to 10 range. Life-cost Based FMEA alleviates this ambiguity by using the estimated cost of failures. Yet, the methods still relies on judgment of experts in determining variables such as frequency, detection time, fixing time, delay time, and parts cost. To resolve this subjectivity, this paper proposes a systematic use of empirical data for applying life-cost-based FMEA. A case study of a large scale particle accelerator shows the advantages of the proposed approach in predicting life cycle failure cost, measuring risk and planning preventive, scheduled maintenance and ultimately improving up-time.


2008 ◽  
Vol 44 (9) ◽  
Author(s):  
Y. Kim ◽  
M. Muste ◽  
A. Hauet ◽  
W. F. Krajewski ◽  
A. Kruger ◽  
...  

2014 ◽  
Vol 687-691 ◽  
pp. 1258-1261
Author(s):  
Jing Sun ◽  
Hong Tao Wang

With the development of computer graphics, real-time rendering-based VF: technology has been applied in more and more fields. LOD is the key technology in large-scale terrain rendering. In this paper, the basic concept of LOD is introduced briefly and some algorithms of LOD in use are mentioned and analyzed; secondly as one of algorithms of LOD, View-Dependent Progressive Mesh algorithm is studied and improved, the result of implementing the large-scale terrain’s LOD by using VDPM is presented. There are key technologies in LOD Large-scale terrain real-time rendering are researched. Relative technologies are presented such as: LOD of the terrain, visibility culling, and cracks eliminate, view-dependent refine, LOD error, technologies of texture etc. Using LOD technology, VR system can greatly reduce the; number of polygons produced in real-time rendering procedure. Finally, we do experimental design work based on the methods and techniques presented by this paper.


Sign in / Sign up

Export Citation Format

Share Document