Design and Simulation of Dual Polarization GST-on-Silicon Nitride Optical Modulator

Grain boundaries have long held a special significance to ceramicists. In part, this has been because it has been impossible until now to actually observe the boundaries themselves. Just as important, however, is the fact that the grain boundaries and their environs have a determing influence on both the mechanisms by which powder compaction occurs during fabrication, and on the overall mechanical properties of the material. One area where the grain boundary plays a particularly important role is in the high temperature strength of hot-pressed ceramics. This is a subject of current interest as extensive efforts are being made to develop ceramics, such as silicon nitride alloys, for high temperature structural applications. In this presentation we describe how the techniques of lattice fringe imaging have made it possible to study the grain boundaries in a number of refractory ceramics, and illustrate some of the findings.

Download Full-text

TEM Studies of Grain Boundary Films in Si3N4 Ceramics

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100088968 ◽

1991 ◽

Vol 49 ◽

pp. 930-931

Author(s):

H.-J. Kleebe ◽

J.S. Vetrano ◽

J. Bruley ◽

M. Rühle

Keyword(s):

Mechanical Properties ◽

High Temperature ◽

Silicon Nitride ◽

Hot Isostatic Pressing ◽

Amorphous Film ◽

Liquid Phase Sintering ◽

Second Phase ◽

High Temperature Mechanical Properties ◽

Triple Points ◽

Boundary Films

It is expected that silicon nitride based ceramics will be used as high-temperature structural components. Though much progress has been made in both processing techniques and microstructural control, the mechanical properties required have not yet been achieved. It is thought that the high-temperature mechanical properties of Si3N4 are limited largely by the secondary glassy phases present at triple points. These are due to various oxide additives used to promote liquid-phase sintering. Therefore, many attempts have been performed to crystallize these second phase glassy pockets in order to improve high temperature properties. In addition to the glassy or crystallized second phases at triple points a thin amorphous film exists at two-grain junctions. This thin film is found even in silicon nitride formed by hot isostatic pressing (HIPing) without additives. It has been proposed by Clarke that an amorphous film can exist at two-grain junctions with an equilibrium thickness.

Download Full-text

Electron Microscopy of Silicon Nitride-Based Ceramics

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100088944 ◽

1991 ◽

Vol 49 ◽

pp. 926-927

Author(s):

Gareth Thomas

Keyword(s):

Electron Microscopy ◽

High Temperature ◽

Silicon Nitride ◽

World Wide ◽

Sintering Temperature ◽

Liquid Phase Sintering ◽

High Temperature Strength ◽

Sintering Additives ◽

Glass Forming ◽

Dense Product

Silicon nitride and silicon nitride based-ceramics are now well known for their potential as hightemperature structural materials, e.g. in engines. However, as is the case for many ceramics, in order to produce a dense product, sintering additives are utilized which allow liquid-phase sintering to occur; but upon cooling from the sintering temperature residual intergranular phases are formed which can be deleterious to high-temperature strength and oxidation resistance, especially if these phases are nonviscous glasses. Many oxide sintering additives have been utilized in processing attempts world-wide to produce dense creep resistant components using Si3N4 but the problem of controlling intergranular phases requires an understanding of the glass forming and subsequent glass-crystalline transformations that can occur at the grain boundaries.

Download Full-text

Examination of Fracture Interfaces in Silicon Nitride

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100113925 ◽

1975 ◽

Vol 33 ◽

pp. 60-61

Author(s):

Nancy J. Tighe

Keyword(s):

Silicon Nitride ◽

Grain Boundary ◽

Crack Growth ◽

Subcritical Crack Growth ◽

Slow Crack Growth ◽

Ceramic Materials ◽

Grain Boundary Sliding ◽

Boundary Phase ◽

Turbine Engines ◽

Boundary Sliding

Silicon nitride is one of the ceramic materials being considered for the components in gas turbine engines which will be exposed to temperatures of 1000 to 1400°C. Test specimens from hot-pressed billets exhibit flexural strengths of approximately 50 MN/m2 at 1000°C. However, the strength degrades rapidly to less than 20 MN/m2 at 1400°C. The strength degradition is attributed to subcritical crack growth phenomena evidenced by a stress rate dependence of the flexural strength and the stress intensity factor. This phenomena is termed slow crack growth and is associated with the onset of plastic deformation at the crack tip. Lange attributed the subcritical crack growth tb a glassy silicate grain boundary phase which decreased in viscosity with increased temperature and permitted a form of grain boundary sliding to occur.

Download Full-text