The Improvement of Signal Integrity (SI) according to The Location of Via in The Vicinity of A Slot in The Reference Plane

Author(s):  
Tae Lee ◽  
Junho Kim ◽  
Hyungsoo Kim ◽  
Pil Jun ◽  
Joungho Kim
2017 ◽  
Vol 14 (4) ◽  
pp. 342-347
Author(s):  
Chang Fei Yee ◽  
Asral Bahari Jambek ◽  
Azremi Abdullah Al-Hadi

Purpose This paper aims to analyze the impact of non-perfect reference plane on the integrity of microstrip differential signals at multi-gigabit transmission on a printed circuit board (PCB). The effects of non-perfect reference contributed by signal crossing over split plane such as impedance discontinuity and crosstalk are investigated by performing analysis in two phases. Design/methodology/approach The first phase involves three-dimensional electromagnetic modeling extraction using Keysight EMPro software. Meanwhile, the second phase involves the import of model extracted from EMPro into simulation using Keysight Advanced Design System that covers insertion loss, return loss, crosstalk, time domain reflectometry and eye diagram. Findings A non-perfect reference plane has a negative impact on signal reflection, attenuation and crosstalk. The analysis results are presented and discussed in detail in the later section of this paper. Originality/value The work that studied the impact of the width and the amount of gaps due to crossing of split planes being experienced on the signal integrity was performed by other researchers. Meanwhile, this paper focused on the impact of length and depth of the gap on signal integrity. These research papers serve as a reference guide for high-speed PCB layout design.


2014 ◽  
Vol 5 (1) ◽  
pp. 737-741
Author(s):  
Alejandro Dueñas Jiménez ◽  
Francisco Jiménez Hernández

Because of the high volume of processing, transmission, and information storage, electronic systems presently requires faster clock speeds tosynchronizethe integrated circuits. Presently the “speeds” on the connections of a printed circuit board (PCB) are in the order of the GHz. At these frequencies the behavior of the interconnects are more like that of a transmission line, and hence distortion, delay, and phase shift- effects caused by phenomena like cross talk, ringing and over shot are present and may be undesirable for the performance of a circuit or system.Some of these phrases were extracted from the chapter eight of book “2-D Electromagnetic Simulation of Passive Microstrip Circuits” from the corresponding author of this paper.


Author(s):  
Teoh King Long ◽  
Ko Yin Fern

Abstract In time domain reflectometry (TDR), the main emphasis lies on the reflected waveform. Poor probing contact is one of the common problems in getting an accurate waveform. TDR probe normalization is essential before measuring any TDR waveforms. The advantages of normalization include removal of test setup errors in the original test pulse and the establishment of a measurement reference plane. This article presents two case histories. The first case is about a Plastic Ball Grid Array package consisting of 352 solder balls where the open failure mode was encountered at various terminals after reliability assessment. In the second, a three-digit display LED suspected of an electrical short failure was analyzed using TDR as a fault isolation tool. TDR has been successfully used to perform non-destructive fault isolation in assisting the routine failure analysis of open and short failure. It is shown to be accurate and reduces the time needed to identify fault locations.


2021 ◽  
Vol 13 (14) ◽  
pp. 2769
Author(s):  
Xiaomei Lu ◽  
Yongxiang Hu ◽  
Ali Omar ◽  
Rosemary Baize ◽  
Mark Vaughan ◽  
...  

Recent studies indicate that the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) aboard the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) satellite provides valuable information about ocean phytoplankton distributions. CALIOP’s attenuated backscatter coefficients, measured at 532 nm in receiver channels oriented parallel and perpendicular to the laser’s linear polarization plane, are significantly improved in the Version 4 data product. However, due to non-ideal instrument effects, a small fraction of the backscattered optical power polarized parallel to the receiver polarization reference plane is misdirected into the perpendicular channel, and vice versa. This effect, known as polarization crosstalk, typically causes the measured perpendicular signal to be higher than its true value and the measured parallel signal to be lower than its true value. Therefore, the ocean optical properties derived directly from CALIOP’s measured signals will be biased if the polarization crosstalk effect is not taken into account. This paper presents methods that can be used to estimate the CALIOP crosstalk effects from on-orbit measurements. The global ocean depolarization ratios calculated both before and after removing the crosstalk effects are compared. Using CALIOP crosstalk-corrected signals is highly recommended for all ocean subsurface studies.


Author(s):  
Kaixuan Song ◽  
Jinchun Gao ◽  
George T. Flowers ◽  
Ziren Wang ◽  
Qingya Li ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document