IMPROVEMENT OF THERMAL COMFORT INSIDE A MOSQUE BUILDING

2016 ◽  
Vol 78 (8-4) ◽  
Author(s):  
Fawaz Ghaleb Noman ◽  
Nazri Kamsah ◽  
Haslinda Mohamed Kamar
Keyword(s):  
Thermal Comfort ◽  
Natural Ventilation ◽  
Ventilation System ◽  
Side Wall ◽  
The West ◽  
Cfd Simulations ◽  
Interior Space ◽  
Flow Simulations ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

A combined natural ventilation and mechanical fans are commonly used to cool the interior space inside the mosques in Malaysia. This article presents a study on thermal comfort in the Al-Jawahir Mosque, located in Johor Bahru, Malaysia. The objective is to assess the thermal comfort inside the mosque under the present ventilation system by determining the Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD). These values were then compared to the limits stated in the ASHRAE Standard-55. It was found that the PMV varies from 1.68 to 2.26 while the PPD varies from 61% to 87%. These show that the condition inside the mosque is quite warm. Computational fluid dynamics (CFD) method was used to carry out flow simulations, to identify a suitable strategy to improve the thermal comfort inside the mosque. Results of CFD simulations show that installing four exhaust fans above the windows on the west-side wall of the mosque is the most effective strategy to improve the thermal comfort inside the mosque. Both the PMV and PPD values can potentially be reduced by more than 60%.

Numerical analysis of local thermal comfort in a plan office under natural ventilation

2019 ◽  
Vol 29 (7) ◽  
pp. 972-986 ◽  
Author(s):  
Xiang Deng ◽  
Zijing Tan
Keyword(s):  
Thermal Comfort ◽  
Natural Ventilation ◽  
Meteorological Data ◽  
Ventilation System ◽  
Comfort Level ◽  
Open Plan ◽  
Computational Fluid Dynamics Cfd ◽  
Internal Volume ◽  
Local Thermal Comfort ◽  
Primary Focus

The utilisation of automatic controlled natural wind in office buildings to maintain indoor thermal comfort has gained wide attention in recent years. Generally, it is not necessary to ensure that the whole internal volume of a building with large open spaces meets thermal comfort requirements. Primary focus should be on occupied areas. Accordingly, the local thermal comfort in an open-plan office with automatic controlled natural ventilation system was investigated numerically and experimentally. A computational fluid dynamics (CFD)-based method was presented for indoor environment and thermal comfort prediction. Long-term in situ measurement was conducted during summer and transition seasons. The meteorological data were collected by a mini weather station located on the roof of the target building. Meanwhile, indoor air velocity, temperature, turbulence intensity and wall temperatures were recorded locally. Three thermal comfort indices, i.e. thermal stratification represented by percentage dissatisfied (PD), the extended predicted mean vote (PMVe) and draught rate were employed to evaluate the thermal comfort level of the interested areas during natural ventilation period. The numerical results revealed a risk of local thermal dissatisfaction under low outdoor temperature and strong windy conditions.

scholarly journals ICCM2015: A Comparison of RANS and LES Computational Methods in Analyzing Ventilation Flow Through a Room Fitted with a Two-Sided Windcatcher

2017 ◽  
Vol 14 (03) ◽  
pp. 1750021 ◽  
Author(s):  
A. Niktash ◽  
B. P. Huynh
Keyword(s):  
Natural Ventilation ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Interior Space ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Through ◽  
Cfd Method ◽  
Good Agreement

A windcatcher is a structure for providing natural ventilation using wind power; it is usually fitted on the roof of a building to exhaust the inside stale air to the outside and supplies the outside fresh air into the building interior space working by pressure difference between outside and inside of the building. In this paper, the behavior of free wind flow through a three-dimensional room fitted with a centered position two-canal bottom shape windcatcher model is investigated numerically, using a commercial computational fluid dynamics (CFD) software package and LES (Large Eddy Simulation) CFD method. The results have been compared with the obtained results for the same model but using RANS (Reynolds Averaged Navier–Stokes) CFD method. The model with its surrounded space has been considered in both method. It is found that the achieved results for the model from LES method are in good agreement with RANS method’s results for the same model.

Numerical Simulation and Analysis of the Two-Sided Windcatcher Inlet\Outlet Effect on Ventilation Flow Through a Three Dimensional Room

2014 ◽  
Author(s):  
Amirreza Niktash ◽  
B. P. Huynh
Keyword(s):  
Flow Velocity ◽  
Flow Pattern ◽  
Natural Ventilation ◽  
Three Dimensional ◽  
Interior Space ◽  
Different Types ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Through ◽  
Cfd Method ◽  
Living Area

A windcatcher is a structure placed on the roof of a building for providing natural ventilation for interior space working by wind power. It draws out the inside stale air to the outside and supplies the outside fresh air for the building’s interior space. In this paper, the effect of different types of windcatcher’s inlet\outlet on the air flow, flow velocity and flowrate through a three-dimensional room fitted with a two-sided windcatcher is observed numerically, using a commercial computational fluid dynamics (CFD) software package. The standard RANS K-ε CFD method is used in the simulations. The flow pattern, flow velocity and flowrate of the inside ventilation flow is considered for the six different types of a two-sided windcatcher’s inlet\outlet. It is found that the shape of the inlet\outlet of windcatcher strongly affects flow pattern, flow velocity and flowrate and the performance of square windcatcher is higher than the circular one specially in ventilating the living area (lower part) of a room.

scholarly journals Using CFD to Evaluate Natural Ventilation through a 3D Parametric Modeling Approach

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2197
Author(s):  
Nayara Rodrigues Marques Sakiyama ◽  
Jurgen Frick ◽  
Timea Bejat ◽  
Harald Garrecht
Keyword(s):  
Natural Ventilation ◽  
Parametric Modeling ◽  
Cfd Simulations ◽  
3D Design ◽  
Post Process ◽  
Test House ◽  
Model Set ◽  
Computational Fluid Dynamics Cfd ◽  
Set Up ◽  
Passive Strategy

Predicting building air change rates is a challenge for designers seeking to deal with natural ventilation, a more and more popular passive strategy. Among the methods available for this task, computational fluid dynamics (CFD) appears the most compelling, in ascending use. However, CFD simulations require a range of settings and skills that inhibit its wide application. With the primary goal of providing a pragmatic CFD application to promote wind-driven ventilation assessments at the design phase, this paper presents a study that investigates natural ventilation integrating 3D parametric modeling and CFD. From pre- to post-processing, the workflow addresses all simulation steps: geometry and weather definition, including incident wind directions, a model set up, control, results’ edition, and visualization. Both indoor air velocities and air change rates (ACH) were calculated within the procedure, which used a test house and air measurements as a reference. The study explores alternatives in the 3D design platform’s frame to display and compute ACH and parametrically generate surfaces where air velocities are computed. The paper also discusses the effectiveness of the reference building’s natural ventilation by analyzing the CFD outputs. The proposed approach assists the practical use of CFD by designers, providing detailed information about the numerical model, as well as enabling the means to generate the cases, visualize, and post-process the results.

The Potential of Natural Ventilation in Single-Sided Ventilated Apartment to Improve Indoor Thermal Comfort and Air Quality

2011 ◽  
Author(s):  
M. F. Mohamed ◽  
M. Behnia ◽  
S. King ◽  
D. Prasad
Keyword(s):  
Air Quality ◽  
Thermal Comfort ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Natural Ventilation ◽  
Architectural Element ◽  
Flat Design ◽  
Effective Ventilation ◽  
Computational Fluid Dynamics Cfd ◽  
Ventilation Performance

Cross ventilation is a more effective ventilation strategy in comparison to single-sided ventilation. In the NSW Residential Flat Design Code1 (RFDC) the majority of apartments are required to adopt cross ventilation. However, in the case of studio and one-bedroom apartments, it is acknowledged that single-sided ventilation may prevail. Deep plan studio and one-bedroom apartments may achieve lower amenity of summer thermal comfort and indoor air quality where mechanical ventilation is not provided by air conditioning. Since compliance with the code may allow up to 40% of apartments in a development in Sydney to be single sided, it is important to understand the natural ventilation performance of such apartments. The objective of this paper is to investigate the natural ventilation potential in single-sided ventilated apartments to improve indoor air quality and thermal comfort. This investigation includes simulating various facade treatments involving multiple opening and balcony configurations. Balcony configurations are included in this study because, in Sydney, a balcony is a compulsory architectural element in any apartment building. The study uses computational fluid dynamics (CFD) software to simulate and predict the ventilation performance of each apartment configuration. This study suggests that properly configured balconies and openings can significantly improve indoor ventilation performance for enhanced indoor air quality and thermal comfort, by optimizing the available prevailing wind. However, it is important to note that inappropriately designed fac¸ade treatments also could diminish natural ventilation performance.

Comparative research on the air pollutant prevention and thermal comfort for different types of ventilation

2020 ◽  
pp. 1420326X2092552
Author(s):  
Yang Zhang ◽  
Wenxuan Yu ◽  
Youli Li ◽  
Han Li
Keyword(s):  
Thermal Comfort ◽  
Cfd Simulation ◽  
Thermal Sensation ◽  
Side Wall ◽  
Air Pollutant ◽  
Indoor Thermal Comfort ◽  
Subjective Experiment ◽  
Different Types ◽  
Computational Fluid Dynamics Cfd ◽  
Indoor Comfort

In this article, a comparative study on the outdoor air pollutant prevention and indoor thermal comfort for different types of ventilation was carried out. Both objective experiment, subjective experiment and computational fluid dynamics (CFD) simulation were conducted to investigate the differences in air pollutant prevention and thermal comfort between four common ventilation methods, namely supplying on the ceiling and returning on the ceiling (SC-RC), supplying on the ceiling and returning on the side wall (SC-RSW), supplying on the side wall and returning on the ceiling (SSW-RC), and supplying on the side wall and returning on the side wall (SSW-RSW). Results show that SSW-RSW can provide the highest indoor air quality according to the indoor average PM2.5 concentration. Overall thermal sensation was introduced to evaluate the indoor comfort under the four ventilation methods. The voting results show that the indoor thermal comfort can be enhanced by 29–36% under SSW-RSW and SSW-RC. Therefore, SSW-RSW is more suitable for providing a healthy and comfortable indoor environment.

scholarly journals Designing Jet Fan Ventilation for an Underground Car Park by CFD Simulations

2018 ◽  
Vol 63 (1) ◽  
pp. 39-43 ◽  
Author(s):  
Miroslava Kmecová ◽  
Michal Krajčík ◽  
Zuzana Straková
Keyword(s):  
Exchange Rate ◽  
High Efficiency ◽  
Ventilation System ◽  
Cfd Simulations ◽  
Air Exchange Rate ◽  
Air Supply ◽  
Car Park ◽  
Computational Fluid Dynamics Cfd ◽  
Alternative Designs ◽  
Air Exchange

The aim of this study was to design a fire ventilation system with impulse jet fans for an underground car park. With respect to the number of parameters affecting the spread of smoke that need to be considered, there is a good chance of miscalculations if only conventional plain calculations are used in the design process. To avoid mistakes, visualize the fluid flow, and to compare the design variants it is practical to use computational fluid dynamics (CFD). In this study, CFD simulations were used to compare alternative designs of a fire ventilation system. In one alternative the exhaust shafts were located in both parts of the car park and the jet fans were directed to the corresponding shafts. The air exchange rate was 10-times per hour. In another alternative both exhaust shafts were located on one side opposite to the main air supply, and the air exchange rate was 15-times per hour. The results showed preference of the second alternative, when the smoke was completely exhausted and the visibility improved substantially, whereas in the first alternative the car park was not sufficiently ventilated even 600 seconds after the fire had been put out. The results emphasize that proper location of elements of the ventilation system is crucial to attain high efficiency of fire ventilation.

Modeling of Buoyancy-Driven Natural Ventilation in Workshop: Optimization of Distance between Heat Source and Ground

2012 ◽  
Vol 170-173 ◽  
pp. 2579-2582 ◽  
Author(s):  
Ya Xin Su ◽  
A Long Su ◽  
Xin Wan
Keyword(s):  
Heat Source ◽  
Indoor Air ◽  
Energy Cost ◽  
Lower Energy ◽  
Natural Ventilation ◽  
Waste Heat ◽  
Heat Sources ◽  
Hot Air ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

Natural ventilation is suitable for application to workshops with heat sources to keep good indoor air quality at lower energy cost. In this paper, the authors numerically investigated the buoyancy-driven natural ventilation in a workshop with heat source based on computational fluid dynamics (CFD) method. The effect of the distance between heat source and ground on the air flow and temperature distribution was examined. Results showed that the average air temperature at operation zone could be effectively reduced when the distance between heat source and ground increased. The temperature field in the upper zone of the workshop was improved by diminishing the hot air zone near the ceiling and the waste heat directly going into the operation zone decreased when the distance between heat source and ground increased.

Sign in / Sign up

Export Citation Format

Share Document