Performance of a Residential-Sized GAX Absorption Chiller

2001 ◽  
Vol 123 (3) ◽  
pp. 236-241 ◽  
Author(s):  
Douglas K. Priedeman ◽  
Michael A. Garrabrant ◽  
James A. Mathias ◽  
Roger E. Stout ◽  
Richard N. Christensen
Keyword(s):  
Market Research ◽  
Experimental Testing ◽  
Research Effort ◽  
Cooling Capacity ◽  
Coefficient Of Performance ◽  
Working Fluid ◽  
Cooling Load ◽  
Absorption Chiller ◽  
Flow Meters ◽  
Pressure Transducers

This research effort involved experimentally testing an advanced-cycle, ammonia-water absorption chiller with a cooling capacity of 17.6 kW (5 refrigeration tons (RT)). The system was a generator-absorber heat exchange (GAX) cycle and was sized for residential and light commercial use, where very little absorption equipment is currently used. The components of the cycle were assembled with instrumentation, including flow meters, pressure transducers, and thermocouples. The findings of the research were cycle cooling load and coefficient of performance (COP), as well as many component heat duties and working fluid state points throughout the cycle. The COP of the chiller at essentially full load was measured at 0.68. A simulation of the GAX cycle was performed with a computer program that predicted the heat duties of each component and the cooling load of the cycle. The simulation of the GAX cycle and experimental testing compared closely. Existing market research shows that significant business opportunities exist for a GAX heat pump or chiller with a cooling COP of 0.70 or greater. The work performed in this study consisted of testing a GAX cycle with a COP that approached the target value of 0.70 and identified improvements that must be made to reach the target COP value.

Thermodynamic analysis of triple effect ammonia–water absorption compression (hybrid) cycle

2021 ◽  
pp. 095440892199568
Author(s):  
CP Jawahar
Keyword(s):  
Water Absorption ◽  
Energy Analysis ◽  
Cooling Capacity ◽  
Coefficient Of Performance ◽  
Working Fluid ◽  
Performance Parameters ◽  
Evaporator Temperature ◽  
Ammonia Water ◽  
Absorption Cycle ◽  
Hybrid Cycle

This paper presents the energy analysis of a triple effect absorption compression (hybrid) cycle employing ammonia water as working fluid. The performance parameters such as cooling capacity and coefficient of performance of the hybrid cycle is analyzed by varying the temperature of evaporator from −10 °C to 10 °C, absorber and condenser temperatures in first stage from 25 °C to 45 °C, degassing width in both the stages from 0.02 to 0.12 and is compared with the conventional triple effect absorption cycle. The results of the analysis show that the maximum cooling capacity attained in the hybrid cycle is 472.3 kW, at 10 °C evaporator temperature and first stage degassing width of 0.12. The coefficient of performance of the hybrid cycle is about 30 to 65% more than the coefficient of performance of conventional triple effect cycle.

scholarly journals Installation and Operation of a Solar Cooling and Heating System Incorporated with Air-Source Heat Pumps

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 996 ◽  
Author(s):  
Li Huang ◽  
Rongyue Zheng ◽  
Udo Piontek
Keyword(s):  
Heating System ◽  
Cooling Capacity ◽  
Heat Pumps ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Energy Yield ◽  
Absorption Chiller ◽  
Annual Average ◽  
Water Storage Tank ◽  
Solar Cooling

A solar cooling and heating system incorporated with two air-source heat pumps was installed in Ningbo City, China and has been operating since 2018. It is composed of 40 evacuated tube modules with a total aperture area of 120 m2, a single-stage and LiBr–water-based absorption chiller with a cooling capacity of 35 kW, a cooling tower, a hot water storage tank, a buffer tank, and two air-source heat pumps, each with a rated cooling capacity of 23.8 kW and heating capacity of 33 kW as the auxiliary system. This paper presents the operational results and performance evaluation of the system during the summer cooling and winter heatingperiod, as well as on a typical summer day in 2018. It was found that the collector field yield and cooling energy yield increased by more than 40% when the solar cooling and heating system is incorporated with heat pumps. The annual average collector efficiency was 44% for cooling and 42% for heating, and the average coefficient of performance (COP) of the absorption chiller ranged between 0.68 and 0.76. The annual average solar fraction reached 56.6% for cooling and 62.5% for heating respectively. The yearly electricity savings accounted for 41.1% of the total electricity consumption for building cooling and heating.

scholarly journals Investigation on the improvement of car air conditioning system performance using an ejector

2018 ◽  
Vol 197 ◽  
pp. 08013
Author(s):  
Enang Suma Arifianto ◽  
Ega Taqwali Berman ◽  
Mutaufiq Mutaufiq
Keyword(s):  
System Performance ◽  
Test Procedure ◽  
Cooling Capacity ◽  
Coefficient Of Performance ◽  
Working Fluid ◽  
Refrigeration Cycle ◽  
Air Conditioner ◽  
Air Conditioning System ◽  
Compressor Work ◽  
R 134A

The purpose of this research is to know the improvement of car air conditioner system performance using an ejector. The study was conducted on a car engine with power 100 PS (74 kW) @ 5000 rpm. The test procedure is carried out under two conditions: the normal refrigeration cycle mode and the refrigeration cycle mode with the ejector. The working fluid used in the refrigeration cycle is R-134a. Performance data was measured on engine revolutions ranging from 1500 - 3000 rpm. Finally, the results showed that ejector usage on AC system generates an increase in the refrigeration effect and coefficient of performance (COP) of 25% and 22%, respectively. This has implications to better cooling capacity and compressor work that is lighter.

scholarly journals Investigation of the launch time of NH3-H2O absorption chiller under different working condition

2019 ◽  
Vol 234 (1) ◽  
pp. 15-28 ◽  
Author(s):  
A Ebrahimnataj Tiji ◽  
A Ramiar ◽  
MR Ebrahimnataj
Keyword(s):  
Working Condition ◽  
Coefficient Of Performance ◽  
Working Fluid ◽  
Liquid Temperature ◽  
Absorption Chiller ◽  
Software Environment ◽  
Matlab Software ◽  
Subcooled Liquid ◽  
Lumped Parameter ◽  
Ammonia Absorption

This study deals with the launch time of main characteristic of NH3-H 2O absorption chiller under different working condition. The aim of this work was about to scrutinize a lumped-parameter dynamic simulation of aqua-ammonia absorption chiller in addition to investigating the effect of subcooled liquid at condenser/absorber outlet on absorption chiller’s key parameters launch time. Also, the effect of ambient temperature on absorption chiller’s key parameters’ launch time is studied. In order to determine the thermodynamic properties of the working fluid, the Engineering Equation Solver software is applied. By making a link between Engineering Equation Solver and MATLAB software, the differential equations are solved in the MATLAB software environment by fourth-order Rung–Kutta method. According to the result, increase of the sub-cool liquid temperature at condenser outlet has no effect on absorption chiller’s key parameters’ launch time. Besides, 10 ℃-increase in subcooled liquid temperature at the absorber outlet leads to decreasing the launch time of the coefficient of performance to 19.35%. The result shows that if cooling tower temperature goes from 22 ℃ to 30 ℃, launch time of the coefficient of performance rises by 10.43%, while evaporator heat transfer rate falls by 30%. To validate the dynamic model, the results deduced from numerical simulation are compared with peer steady–state results.

scholarly journals Experimental Investigation of a Split Air Conditioning Using Condensate as Direct Evaporative Cooling

2021 ◽  
Vol 86 (1) ◽  
pp. 140-153
Author(s):  
Azridjal Aziz ◽  
Muhammad Rif’at Syahnan ◽  
Afdhal Kurniawan Mainil ◽  
Rahmat Iman Mainil
Keyword(s):  
Air Conditioning ◽  
Evaporative Cooling ◽  
Cooling Capacity ◽  
Coefficient Of Performance ◽  
Cooling Load ◽  
Air Conditioner ◽  
Direct Evaporative Cooling ◽  
Compressor Power ◽  
Discharge Pressure ◽  
Air Conditioning Systems

Split air conditioning systems produce reasonable amount of condensate which is usually not utilized and thrown away to the environment. On the other hand, it consumes a lot of energy during operation. The aim of this study is to investigate the improvement of air conditioning systems performance utilizing condensate. A direct evaporative cooling using condensate is incorporated on a 0.74 ton-cooling capacity of split air conditioning to decrease the air temperature before entering the condenser. Performances of the split air conditioning with and without direct evaporative cooling are compared and presented in this paper. The results show that the use of direct evaporative cooling using condensate into the air before passing through the condenser reduces the compressor discharge pressure. The decrease of the condenser pressure led to 4.7% and 7% reduction of power consumption for air conditioner without cooling load and air conditioner with 2000 W cooling load, respectively. The cooling effect and coefficient of performance (COP) increase with the decrease of compressor power. The use of direct evaporative cooling with condensate into the air before entering the condensing system can enhance the system performance and protect the environment.

Numerical Study of Ejector as an Expansion Device in Split-Type Air Conditioner

2013 ◽  
Vol 388 ◽  
pp. 101-105 ◽  
Author(s):  
Kasni Sumeru ◽  
Nasution Henry ◽  
Farid Nasir Ani
Keyword(s):  
Capillary Tube ◽  
Numerical Study ◽  
Geographical Area ◽  
Numerical Approach ◽  
Cooling Capacity ◽  
Coefficient Of Performance ◽  
Working Fluid ◽  
Air Conditioner ◽  
Constant Area ◽  
Condenser Temperature

This paper presents a numerical approach for determining the motive nozzle and constant-area of an ejector as an expansion device, based on cooling capacity of the split-type air conditioner using R22 as working fluid. The use of an ejector as an expansion device in split-type air conditioner can enhance the coefficient of performance (COP) system. Typically, the split-type air conditioner may be installed on the geographical area with moderate or high outdoor air temperature using capillary tube. For this reason, the motive nozzle and constant-area diameters of the ejector must be designed according to these conditions. The diameters of the ejector are crucial in improving the COP. The results showed that the motive nozzle diameter is constant (1.14 mm) with variations of the condenser temperature, whereas the constant-area diameter decreases as the condenser temperature increases.

Experimental Study About Performance Analysis of Parallel Connected Ranque–Hilsch Counter Flow Vortex Tubes With Different Nozzle Numbers and Materials

2018 ◽  
Vol 140 (11) ◽  
Author(s):  
Hüseyin Kaya ◽  
Fahrettin Günver ◽  
Onuralp Uluer ◽  
Volkan Kırmacı
Keyword(s):  
Exergy Analysis ◽  
Vortex Tube ◽  
Cooling Capacity ◽  
Coefficient Of Performance ◽  
Inlet Pressure ◽  
Working Fluid ◽  
Counter Flow ◽  
Heating And Cooling ◽  
Flow Vortex ◽  
Vortex Tubes

An experimental analysis for parallel connected two identical counter flow Ranque–Hilsch vortex tubes (RHVT) with different nozzle materials and numbers was conducted by using compressed air as a working fluid in this paper. Heating and cooling performance of vortex tube system (circuit) and the results of exergy analysis are researched comprehensively according to different inlet pressure, nozzle numbers, and materials. Nozzles made of polyamide plastic, aluminum, and brass were mounted into the vortex tubes individually for each case of experimental investigation with the numbers of nozzles 2, 3, 4, 5, and 6. The range of operated inlet pressure 150–550 kPa with 50 kPa variation. The ratio of length–diameter (L/D) of each vortex tube in the circuit is 14 and the cold mass fraction is 0.36. Coefficient of performance (COP) values, heating, and cooling capacity of the parallel connected RHVT system were evaluated. Further, an exergy analysis was carried out to evaluate the energy losses and second law efficiency of the vortex tube circuit. The greatest thermal performance was obtained with aluminum-six-nozzle when taking into account all parameters such as temperature difference, COP values, heating and cooling capacity, and exergy analysis.

Performance of Thermoacoustic Refrigerators: Cooling Load and Coefficient of Performance

2008 ◽  
Author(s):  
Cila Herman ◽  
Christopher Lavin ◽  
Zdeneˇk Tra´vni´cˇek
Keyword(s):  
Coefficient Of Performance ◽  
Working Fluid ◽  
Cooling Load ◽  
Working Fluids ◽  
Half Wavelength ◽  
Environmentally Safe ◽  
Pure Helium ◽  
Limiting Case ◽  
Load Behavior ◽  
Thermoacoustic Refrigeration

Thermoacoustic refrigeration is an environmentally safe refrigeration technology that has evolved over the past three decades [1–5]. The influence of working fluid on the performance of the thermoacoustic refrigerator (TAR) expressed in terms of the cooling load and the coefficient of performance is discussed in the paper. The calculations rely on the short stack boundary layer approximation. A simple model of a one-dimensional half wavelength resonance tube equipped with stack plates and a pair of heat exchangers was used as the physical model. It is known that a TAR with noble gases and their mixtures as working fluids can achieve high values of the coefficient of performance (COP) because of small Prandtl number values. The present study revealed and quantified that cooling load behavior is quite different from the performance in terms of the COP: the highest cooling load is achieved with pure Helium as the working fluid. A reason is the very high sound speed in Helium. TARs with Helium as the working fluids deliver the highest cooling load of all gases and their mixtures examined here, therefore it has been suggested as a limiting case of the most powerful TAR. The influence of geometry and thermophysical parameters of the device on TAR performance was studied systematically and a performance sensitiviy analysis was presented with particular emphasis on TAR cooling load.

scholarly journals Solar ejector refrigerant system in China’s residential buildings

2014 ◽  
Vol 18 (5) ◽  
pp. 1643-1647
Author(s):  
Hui-Fan Zheng ◽  
Xiao-Wei Fan ◽  
Fang Wang ◽  
Guo-Ji Tian
Keyword(s):  
Air Conditioning ◽  
Residential Buildings ◽  
Cooling Capacity ◽  
Coefficient Of Performance ◽  
Simulation Program ◽  
Efficiency Coefficient ◽  
Cooling Load ◽  
Collector Efficiency

A simulation program describing the performance of solar ejector refrigerant system for air conditioning of China?s residential buildings was established. Hourly performance of the system under different operate conditions, the collector efficiency, coefficient of performance, cooling capacity and cooling load were analyzed. It is found that the collector efficiency and the overall coefficient of performance increase first and then decline, and it can be concluded that the application of solar ejector refrigerant system will have a better developmental prospect in China?s residential buildings.

Sign in / Sign up

Export Citation Format

Share Document