Modeling of the Rate Responsive Behavior of Elastomer Foam Materials

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
Feixia Pan
Keyword(s):  
Finite Element ◽  
Constitutive Model ◽  
Test Data ◽  
Experimental Test ◽  
Strain Rates ◽  
Foam Material ◽  
Material Models ◽  
Rate Dependent ◽  
Responsive Behavior ◽  
Rate Responsive

Elastomer foam materials are shock absorbers that have been extensively used in applications of electronic packaging. Finite element modeling simulation plays an important role in helping the designers determine the best elastomer foam material and the best structure of a shock absorber. Elastomer foam materials have very complicated material behaviors. The prediction of the rate responsive behavior is one of the most interesting topics in elastomer material modeling. The focus of this article is to present a unique method for deriving the rate dependent constitutive model of an elastomer foam based on the extension of the Cowper and Symond law and the curve fitting on experimental test data. The research on rate dependent material models and the material models available in commercially available finite element analysis software have been reviewed. Test data collection at various strain rates has been discussed. Two steps of curve fitting on experimental test data are used to retrieve analytical expression of the constitutive model. The performance of the constitutive model for a foam material has been illustrated and shown to be quite good. This method is easy to understand and the simple formulation of the constitutive model is very suitable for applications in numerical simulation. The constitutive model could be used to predict the stress-strain curves of a foam material at any strain rate, especially at the intermediate strain rates, which are the most difficult to collect so far. In addition, this model could be readily integrated with the hyperelastic material models to more efficiently evaluate the mechanical behavior of an elastomer foam material. The model could potentially be implemented in commercially available software such as ABAQUS and LS-DYNA. The method presented is also useful in deriving constitutive models of rubberlike elastomer materials.

Rate-Dependent Constitutive Modeling of Polymer Subjected to Dynamic Loading

2012 ◽  
Vol 185 ◽  
pp. 119-121
Author(s):  
Jian Ming Yuan ◽  
Jan Ma ◽  
Geoffrey E.B. Tan ◽  
Jian Fei Liu
Keyword(s):  
Test Data ◽  
Constitutive Modeling ◽  
Dynamic Compression ◽  
Fem Simulation ◽  
Material Model ◽  
Strain Rates ◽  
Compression Tests ◽  
Material Models ◽  
Rate Dependent ◽  
Tension Tests

This paper proposes an effective and systematical method to obtain reliable rate-dependent material models used in FEM simulation for polymers. Compressive stress-strain curves of two types of polymer are obtained at different strain rates. Rate-dependent elastic-plastic models are applied to describe the observed rate-dependent behaviors, whereby the input data of material model are determined from the test data obtained. Verification of the material models is proposed via comparing FEM simulation with test data of quasi-static tension tests and dynamic compression tests of different strain rates.

scholarly journals Biaxial estimation of biomechanical constitutive parameters of passive porcine sclera soft tissue

2021 ◽  
Author(s):  
Zwelihle Ndlovu ◽  
Dawood Desai ◽  
Thanyani Pandelani ◽  
Harry Ngwangwa ◽  
Fulufhelo Nemavhola
Keyword(s):  
Finite Element ◽  
Soft Tissue ◽  
Finite Element Model ◽  
Test Data ◽  
Element Model ◽  
Finite Element Models ◽  
Anisotropic Model ◽  
Material Models ◽  
Material Parameters ◽  
Constitutive Parameters

This study assesses the modelling capabilities of four constitutive hyperplastic material models to fit the experimental data of the porcine sclera soft tissue. It further estimates the material parameters and discusses their applicability to a finite element model by examining the statistical dispersion measured through the standard deviation. Fifteen sclera tissues were harvested from porcine’ slaughtered at an abattoir and were subjected to equi-biaxial testing. The results show that all the four material models yielded very good correlations at correlations above 96 %. The polynomial (anisotropic) model gave the best correlation of 98 %. However, the estimated material parameters varied widely from one test to another such that there would be needed to normalise the test data to avoid long optimisation processes after applying the average material parameters to finite element models. However, for application of the estimated material parameters to finite element models, there would be needed to consider normalising the test data to reduce the search region for the optimisation algorithms. Although the polynomial (anisotropic) model yielded the best correlation, it was found that the Choi-Vito had the least variation in the estimated material parameters thereby making it an easier option for application of its material parameters to a finite element model and also requiring minimum effort in the optimisation procedure. For the porcine sclera tissue, it was found that the anisotropy more influenced by the fiber-related properties than the background material matrix related properties.

scholarly journals Extension of Flow Behaviour and Damage Models for Cast Iron Alloys with Strain Rate Effect

2020 ◽  
Author(s):  
Chuang Liu ◽  
Dongzhi Sun ◽  
Xianfeng Zhang ◽  
Florence Andrieux ◽  
Tobias Gerster
Keyword(s):  
Cast Iron ◽  
Constitutive Model ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Damage Model ◽  
Iron Alloys ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Damage Models ◽  
Rate Dependent

Abstract Cast iron alloys with low production cost and quite good mechanical properties are widely used in the automotive industry. To study the mechanical behavior of a typical ductile cast iron (GJS-450) with nodular graphite, uni-axial quasi-static and dynamic tensile tests at strain rates of 10− 4, 1, 10, 100, and 250 s− 1 were carried out. In order to investigate the effects of stress state, specimens with various geometries were used in the experiments. Stress–strain curves and fracture strains of the GJS-450 alloy in the strain-rate range of 10− 4 to 250 s− 1 were obtained. A strain rate-dependent plastic flow law based on the Voce model is proposed to describe the mechanical behavior in the corresponding strain-rate range. The deformation behavior at various strain rates is observed and analyzed through simulations with the proposed strain rate-dependent constitutive model. The available damage model from Bai and Wierzbicki is extended to take the strain rate into account and calibrated based on the analysis of local fracture strains. The validity of the proposed constitutive model including the damage model was verified by the corresponding experimental results. The results show that the strain rate has obviously nonlinear effects on the yield stress and fracture strain of GJS-450 alloys. The predictions with the proposed constitutive model and damage models at various strain rates agree well with the experimental results, which illustrates that the rate-dependent flow rule and damage models can be used to describe the mechanical behavior of cast iron alloys at elevated strain rates.

Thermo-Elastoviscoplastic Buckling Behavior of Plates

1994 ◽  
Vol 61 (1) ◽  
pp. 169-175 ◽  
Author(s):  
G. J. Simitses ◽  
Y. Song
Keyword(s):  
Finite Element ◽  
Constitutive Equations ◽  
Material Models ◽  
Inelastic Buckling ◽  
Finite Element Approach ◽  
Numerical Examples ◽  
Initial Imperfections ◽  
Rate Dependent ◽  
Buckling Behavior ◽  
Element Approach

The thermo-elastoviscoplastic buckling behavior of plates is investigated. The analysis is based on nonlinear kinematic relations and nonlinear rate-dependent unified constitutive equations which include both Bodner-Partom’s and Walker’s material models. A finite element approach is employed to predict the inelastic buckling behavior. Numerical examples are given to demonstrate the effects of several parameters, which include temperature, small initial imperfections, and the thickness of the plate. Comparisons of buckling responses for the two models, Bodner-Partom’s and Walker’s, are also presented.

A Numerical Study on Ductile Failure of Porous Ductile Solids With Rate-Dependent Matrix Behavior

2019 ◽  
Vol 87 (3) ◽  
Author(s):  
Lars Edvard Blystad Dæhli ◽  
David Morin ◽  
Tore Børvik ◽  
Ahmed Benallal ◽  
Odd Sture Hopperstad
Keyword(s):  
Finite Element ◽  
Strain Rate ◽  
Strain Localization ◽  
Ductile Failure ◽  
Unit Cell ◽  
Strain Rates ◽  
Proportional Loading ◽  
Loading Paths ◽  
Rate Dependent ◽  
Constitutive Formulation

Abstract This work examines the effects of loading rate on the plastic flow and ductile failure of porous solids exhibiting rate-dependent behavior relevant to many structural metals. Two different modeling approaches for ductile failure are employed and numerical analyses are performed over a wide range of strain rates. Finite element unit cell simulations are carried out to evaluate the macroscopic mechanical response and ductile failure by void coalescence for various macroscopic strain rates. The unit cell results are then used to assess the accuracy of a rate-dependent porous plasticity model, which is subsequently used in strain localization analyses based on the imperfection band approach. Strain localization analyses are conducted for (i) proportional loading paths and (ii) non-proportional loading paths obtained from finite element simulations of axisymmetric and flat tensile specimens. The effects of strain rate are most apparent on the stress–strain response, whereas the effects of strain rate on ductile failure is found to be small for the adopted rate-dependent constitutive model. However, the rate-dependent constitutive formulation tends to regularize the plastic strain field when the strain rate increases. In the unit cell simulations, this slightly increases the strain at coalescence with increasing strain rate compared to a rate-independent constitutive formulation. When the strain rate is sufficiently high, the strain at coalescence becomes constant. The strain localization analyses show a negligible effect of strain rate under proportional loading, while the effect of strain rate is more pronounced when non-proportional loading paths are assigned.

A Second Generation of Numerical Implementation of Nonlinear Piezoelectric Models in Commercially Available Tools

2008 ◽  
Author(s):  
M. A. Siddiq Qidwai ◽  
V. G. DeGiorgi
Keyword(s):  
Finite Element ◽  
Constitutive Model ◽  
Domain Switching ◽  
Piezoelectric Materials ◽  
Nonlinear Behavior ◽  
Material Behavior ◽  
Device Performance ◽  
Performance Improvements ◽  
Rate Dependent ◽  
Theoretical Developments

Domain switching based nonlinear behavior is characteristic of relaxor-type piezoelectric material such as PMN-PT single crystals. These materials offer significant device performance improvements over traditional polycrystalline piezoelectric materials such as PZT-5A. The promise of increased performance of these materials has led to work in development of constitutive characterizations so that material behavior under load and material failure mechanisms can be understood and predicted. However, there is a gap between development of such theoretical developments and in workable manifestations available as part of commercial finite element codes for use in device design. In the current work, the authors extend previously documented implementation of a macro-mechanical constitutive model which addresses domain switching, into a commercially available finite element code. A rate dependent version of the constitutive model has been successfully realized and used to reproduce a variety of piezoelectric constitutive behaviors.

Rate-Dependent Behavior and Constitutive Model of Polycarbonate at Strain Rate from 10-5 to 103 S-1

2011 ◽  
Vol 117-119 ◽  
pp. 434-437
Author(s):  
Wen Jun Hu ◽  
Xi Cheng Huang ◽  
Fang Ju Zhang ◽  
Cheng Jun Chen
Keyword(s):  
Constitutive Model ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Temperature Dependent ◽  
Static Tests ◽  
Rate Range ◽  
Rate Dependent ◽  
Dependent Behavior

Uni-axial quasi-static tests at strain rates 10-5, 10-4, 10-3,10-2 and 10-1 s-1 and dynamic compressive tests at strain rates 1679, 2769,5000 and 8200 s-1 have been carried out to study the mechanical behavior for polycarbonate used in the avigation industry. The stress–strain curves of polycarbonate in the strain-rate range from 10-5 to 8200 s-1 have been obtained. The effects of the strain rate on yield phenomenon and rate-dependent mechanical behavior are discussed. A plastic flow law based on the DSGZ rate-temperature-dependent constitutive model was used to describe the mechanical behavior of polycarbonate in the strain-rate range from 10-5 to 103 s-1. The results at the six strain rates are in excellent agreement with the experimental data, which illustrates that the constitutive model can describe the mechanical behavior for polycarbonate at low and high strain rates perfectly.

Research on WALKER Constitutive Model Tangent Modulus

2012 ◽  
Vol 249-250 ◽  
pp. 113-117
Author(s):  
Yan Chen ◽  
Qing Wu Wang ◽  
Quan Shan
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Constitutive Model ◽  
Constitutive Equations ◽  
Tangent Modulus ◽  
Finite Element Code ◽  
Numerical Examples ◽  
Rate Dependent ◽  
Backward Euler ◽  
Elasto Plasticity

In elasto-plasticity computation on materials by sub-increase finite element method, in general, it is necessary to calculate the consistent tangent modulus of elements. In this paper, based on the backward Euler integration, for an unified viscoplasticity constitutive equations, a new expression of consistent tangent modulus is derived for rate-dependent plasticity. The constitutive equations and consistent tangent modulus expression are implemented into a commercial finite element code-MARC. Numerical examples are given to verify the finite element implementation.This template explains and demonstrates how to prepare your camera-ready paper for Trans Tech Publications. The best is to read these instructions and follow the outline of this text.

A constitutive model for frozen soil based on rate-dependent damage evolution

2017 ◽  
Vol 27 (10) ◽  
pp. 1589-1600 ◽  
Author(s):  
Chenxu Cao ◽  
Zhiwu Zhu ◽  
Tiantian Fu ◽  
Zhijie Liu
Keyword(s):  
Constitutive Model ◽  
Damage Evolution ◽  
Mechanical Response ◽  
Split Hopkinson Pressure Bar ◽  
Frozen Soil ◽  
Experimental Results ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Dynamic Mechanical ◽  
Rate Dependent

The deformation of frozen soil under impact loading is usually accompanied by the evolution of internal defects and microdamage. By taking the strain and strain rates into account, a rate-dependent damage evolution law is proposed in this study, under the assumption of equivalent strain. Subsequently, a damage-modified rate-dependent constitutive model is proposed to describe the dynamic mechanical properties of frozen soil. A split Hopkinson pressure bar is utilized to test the dynamic mechanical response of frozen soil at different temperatures and high strain rates. The experimental results show that frozen soil produces obvious strain rate and temperature effects, and that there is a linear relationship between the peak stress and temperature. The theoretical results of the proposed constitutive model agree well with the experimental results, verifying the applicability of the model.

scholarly journals Mechanical Behaviors of Flax Fiber-Reinforced Composites at Different Strain Rates and Rate-Dependent Constitutive Model

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 854 ◽  
Author(s):  
Dayong Hu ◽  
Linwei Dang ◽  
Chong Zhang ◽  
Zhiqiang Zhang
Keyword(s):  
Constitutive Model ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Flax Fiber ◽  
Fiber Reinforced Composites ◽  
Strain Rates ◽  
Reinforced Composites ◽  
Dynamic Mechanical ◽  
Rate Dependent ◽  
Dynamic Mechanical Behavior

Flax fiber-reinforced composites (FFRCs) exhibit excellent environmentally friendly qualities, such as light weight, low cost, recyclability, and excellent mechanical properties. Understanding the dynamic mechanical behavior of FFRCs could broaden their potential applications in lightweight, crashworthy, and impact-critical structures. This study presents a study on the fabrication of FFRCs by vacuum-assisted resin infusion. The dynamic stress–strain responses of the fabricated specimens at strain rates ranging from 0.006 s-1 to 2200 s-1 were evaluated using quasi-static tests and the Split–Hopkinson pressure bar (SHPB). The results indicated that the FFRC exhibited superior strain rate sensitivity. Final deformation photographs and scanning electron micrographs clearly revealed the damage evolution of the FFRC specimens, as well as various failure mechanisms, including fiber–matrix debonding, fiber pull-out, and fiber fracture at different strain rates. On the basis of the experimental results, a simplified Johnson–Cook model was established to describe the strain-rate dependent constitutive model of FFRC. The validation of the suggested constitutive model was embedded in the finite element simulations and could well repeat the strain wave observed from the experiment results. Finally, the quasi-static compression and drop-hammer impact of pyramidal lattice structures with FFRC cores were investigated both numerically and experimentally, proving the effectiveness of the simplified Johnson–Cook model. This study could potentially contribute to a deeper understanding of the dynamic mechanical behavior of FFRCs and provide fundamental experimental data for future engineering applications.

Sign in / Sign up

Export Citation Format

Share Document