The Effect of Rotary Arms on Corotating Disk Flow

1995 ◽  
Vol 117 (2) ◽  
pp. 259-262 ◽  
Author(s):  
John Girard ◽  
Scott Abrahamson ◽  
Kevin Uznanski
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Radial Flow ◽  
Disk Drives ◽  
Number Range ◽  
Reynolds Number Range ◽  
Through Flow ◽  
Dominant Feature ◽  
Flow Visualizations ◽  
The Impact

This investigation studied the impact of rotary style arms on the flow between corotating disks contained by a stationary cylindrical enclosure. Both ventilated and nonventilated hub configurations were considered. The particular geometry used represents a simplified model for common disk drives. Flow visualizations were performed over the Reynolds number range of 3.4 × 104 to 3.4 × 105. The arms were observed to dramatically alter the flow field and to produce an azimuthal pressure gradient throughout the flow field. The dominant feature of the flow between two disks was the arm wake. Moreover, an exchange of fluid across the shroud opening, which provided arm access, was observed. Arm effects became stronger as the arm tips were positioned closer to the hub. The combination of arms and radial through flow was studied over a similar Reynolds number range. In this case, the flow field remained dominated by arm effects, although some effects arising from the radial flow were observed.

Fluid Dynamics Measurements and Flow Visualizations of a Free Slot Jet of Air

2003 ◽  
Author(s):  
F. Gori ◽  
E. Nino
Keyword(s):  
Fluid Dynamics ◽  
Reynolds Number ◽  
Jet Flow ◽  
Hydraulic Diameter ◽  
Hot Wire ◽  
Number Range ◽  
Reynolds Number Range ◽  
Experimental Apparatus ◽  
Hot Wire Anemometry ◽  
Flow Visualizations

The paper reports flow visualizations of a free slot jet of air, obtained with the shadowgraph technique, in the Reynolds number range allowed by the experimental apparatus, i.e. from Re=1,682 to Re=22,107. The Reynolds number is based on the hydraulic diameter of the slot. The shadowgraphs have confirmed the presence of the undisturbed region of flow, which is the zone of the jet flow where velocity and turbulence are about the same as those measured on the slot exit. The undisturbed region of flow is dependent on the Reynolds number. It is higher than three times the slot height, for Re=1,682, and equal to the slot height, for Re=22,107. To confirm the findings of the visualizations, fluid dynamics measurements have been carried out with the hot wire anemometry. The fluid dynamics measurements have confirmed these values with a little over-prediction.

scholarly journals Experimental Investigation of Centrifugal Flow in Rotor–Stator Cavities at High Reynolds Numbers >108

2021 ◽  
Vol 6 (2) ◽  
pp. 13
Author(s):  
Tilman Schröder ◽  
Sebastian Schuster ◽  
Dieter Brillert
Keyword(s):  
Reynolds Number ◽  
Pressure Distribution ◽  
Radial Pressure ◽  
Reynolds Numbers ◽  
Axial Thrust ◽  
Number Range ◽  
High Reynolds Numbers ◽  
Reynolds Number Range ◽  
Through Flow ◽  
High Reynolds

The designers of radial turbomachinery need detailed information on the impact of the side chamber flow on axial thrust and torque. A previous paper investigated centripetal flow through narrow rotor–stator cavities and compared axial thrust, rotor torque and radial pressure distribution to the case without through-flow. Consequently, this paper extends the investigated range to centrifugal through-flow as it may occur in the hub side chamber of radial turbomachinery. The chosen operating conditions are representative of high-pressure centrifugal compressors used in, for example, carbon capture and storage applications as well as hydrogen compression. To date, only the Reynolds number range up to Re=2·107 has been investigated for centrifugal through-flow. This paper extends the range to Reynolds numbers of Re=2·108 and reports results of experimental and numerical investigations. It focuses on the radial pressure distribution in the rotor–stator cavity and shows the influence of the Reynolds number, cavity width and centrifugal mass flow rate. It therefore extends the range of available valid data that can be used to design radial turbomachinery. Additionally, this analysis compares the results to data and models from scientific literature, showing that in the higher Reynolds number range, a new correlation is required. Finally, the analysis of velocity profiles and wall shear delineates the switch from purely radial outflow in the cavity to outflow on the rotor and inflow on the stator at high Reynolds numbers in comparison to the results reported by others for Reynolds numbers up to Re=2·107.

Vortex shedding from a circular cylinder in moderate-Reynolds-number shear flow

1980 ◽  
Vol 101 (4) ◽  
pp. 721-735 ◽  
Author(s):  
Masaru Kiya ◽  
Hisataka Tamura ◽  
Mikio Arie
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Shear Flow ◽  
Vortex Shedding ◽  
Transverse Velocity ◽  
Number Range ◽  
Uniform Shear ◽  
Reynolds Number Range ◽  
Moderate Reynolds Number ◽  
Shear Parameter

The frequency of vortex shedding from a circular cylinder in a uniform shear flow and the flow patterns around it were experimentally investigated. The Reynolds number Re, which was defined in terms of the cylinder diameter and the approaching velocity at its centre, ranged from 35 to 1500. The shear parameter, which is the transverse velocity gradient of the shear flow non-dimensionalized by the above two quantities, was varied from 0 to 0·25. The critical Reynolds number beyond which vortex shedding from the cylinder occurred was found to be higher than that for a uniform stream and increased approximately linearly with increasing shear parameter when it was larger than about 0·06. In the Reynolds-number range 43 < Re < 220, the vortex shedding disappeared for sufficiently large shear parameters. Moreover, in the Reynolds-number range 100 < Re < 1000, the Strouhal number increased as the shear parameter increased beyond about 0·1.

scholarly journals Numerical simulation and experimental research of cavitation nozzle based on equation curve

2021 ◽  
Author(s):  
Lifu Wang ◽  
Dongyan Shi ◽  
Zhixun Yang ◽  
Guangliang Li ◽  
Chunlong Ma ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Reynolds Number ◽  
Flow Field ◽  
High Speed ◽  
Quadratic Equation ◽  
Outer Contour ◽  
Study Results ◽  
Fluent Software ◽  
The Impact ◽  
Better Than

Abstract To further investigate and improve the cleaning ability of the cavitation nozzle, this paper proposes a new model that is based on the Helmholtz nozzle and with the quadratic equation curve as the outer contour of the cavitation chamber. First, the numerical simulation of the flow field in the nozzle chamber was conducted using FLUENT software to analyze and compare the impact of the curve parameters and Reynolds number on the cleaning effect. Next, the flow field was captured by a high-speed camera in order to study the cavitation cycle and evolution process. Then, experiments were performed to compare the cleaning effect of the new nozzle with that of the Helmholtz nozzle. The study results demonstrate that effective cavitation does not occur when the diameter of the cavitation chamber is too large. For the new nozzle, with the increase of the Reynolds number, the degree of cavitation in the chamber first increases and then decreases; the cleaning effect is much better than that of a traditional Helmholtz nozzle under the same conditions; the nozzle has the best cleaning effect for the stand-off distance of 300 mm.

scholarly journals Asymmetrical Split-and-Recombine Micromixer with Baffles

Micromachines ◽  
2019 ◽  
Vol 10 (12) ◽  
pp. 844 ◽  
Author(s):  
Wasim Raza ◽  
Kwang-Yong Kim
Keyword(s):  
Reynolds Number ◽  
Geometrical Parameters ◽  
Mixed Species ◽  
Mixing Index ◽  
Number Range ◽  
Mixing Performance ◽  
Curved Channels ◽  
Advection Diffusion Equation ◽  
Advection Diffusion ◽  
Reynolds Number Range

The present work proposes a planar micromixer design comprising hybrid mixing modules of split-and-recombine units and curved channels with radial baffles. The mixing performance was evaluated numerically by solving the continuity and momentum equations along with the advection-diffusion equation in a Reynolds number range of 0.1–80. The variance of the concentration of the mixed species was considered to quantify the mixing index. The micromixer showed far better mixing performance over whole Reynolds number range than an earlier split-and-recombine micromixer. The mixer achieved mixing indices greater than 90% at Re ≥ 20 and a mixing index of 99.8% at Re = 80. The response of the mixing quality to the change of three geometrical parameters was also studied. A mixing index over 80% was achieved within 63% of the full length at Re = 20.

Strut Interference Effects on Pitot Tube Velocity Measurements

2007 ◽  
Author(s):  
Sandra K. S. Boetcher ◽  
Ephraim M. Sparrow
Keyword(s):  
Reynolds Number ◽  
Reynolds Numbers ◽  
The Body ◽  
Pitot Tube ◽  
Velocity Measurements ◽  
Measuring Device ◽  
Number Range ◽  
Low Reynolds Numbers ◽  
Velocity Measuring ◽  
The Impact

The possible impact of the presence of the strut portion of a Pitot tube on the efficacy of the tube as a velocity-measuring device has been evaluated by numerical simulation. At sufficiently low Reynolds numbers, there is a possibility that the precursive effects of the strut could alter the flow field adjacent to the static taps on the body of the Pitot tube and might even affect the impact pressure measured at the nose. The simulations were performed in dimensionless form with the Reynolds number being the only prescribed parameter, but the dimensions were taken from a short-shanked Pitot tube. Over the Reynolds number range from 1500 to 4000, a slight effect of the strut was identified. However, the variation due to the presence of the shank of the velocity measured by the Pitot tube operating in that range of Reynolds numbers was only 1.5%.

Sign in / Sign up

Export Citation Format

Share Document