Local Characteristics of Convective Heat Transfer From Simulated Microelectronic Chips to Impinging Submerged Round Water Jets

1993 ◽  
Vol 115 (1) ◽  
pp. 71-77 ◽  
Author(s):  
H. Sun ◽  
C. F. Ma ◽  
W. Nakayama
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Convective Heat Transfer ◽  
Stagnation Point ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Rates ◽  
Local Characteristics ◽  
Plate Spacing ◽  
Water Jets

An experimental study was performed to investigate the local characteristics of heat transfer from vertical simulated micro-chips to impinging submerged circular water jets. The effects of jet velocity, and nozzle-to-plate spacing were studied in the range of Re = 5.0 × 103 ˜ 3.6 × 104. Heat transfer rates at the stagnation point and local heat transfer distributions were correlated. Transition from laminar to turbulent flow was observed.

scholarly journals Empirical mapping of the convective heat transfer coefficients with local hot spots on highly conductive surfaces

2017 ◽  
Vol 21 (3) ◽  
pp. 1231-1240
Author(s):  
Murat Tekelioğlu
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Hot Spots ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Transfer Rates ◽  
Heat Transfer Coefficients ◽  
Convective Heat Transfer Coefficients

An experimental method was proposed to assess the natural and forced convective heat transfer coefficients on highly conductive bodies. Experiments were performed at air velocities of 0m/s, 4.0m/s, and 5.4m/s, and comparisons were made between the current results and available literature. These experiments were extended to arbitrary-shape bodies. External flow conditions were maintained throughout. In the proposed method, in determination of the surface convective heat transfer coefficients, flow condition is immaterial, i.e., either laminar or turbulent. With the present method, it was aimed to acquire the local heat transfer coefficients on any arbitrary conductive shape. This method was intended to be implemented by the heat transfer engineer to identify the local heat transfer rates with local hot spots. Finally, after analyzing the proposed experimental results, appropriate decisions can be made to control the amount of the convective heat transfer off the surface. Limited mass transport was quantified on the cooled plate.

Experimental Study on Convective Heat Transfer of Radial Air Flow in Rotating Multi-Channels

1995 ◽  
Author(s):  
G. J. Hwang ◽  
C. R. Kuo ◽  
C. Y. Chang
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Air Flow ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Cross Sectional ◽  
Transfer Measurement ◽  
Single Flow

Experimental study on the convective heat transfer of radial air flow in rotating multi-channels was performed. Three sets of test sections, one single-flow passage, one nine-flow passages and one twenty-five-flow passages with the same cross sectional area of 9π mm2, were applied to the experiments. The test section was formed by rectangular blocks of aluminum alloy with circular flow passages. Between two adjacent blocks, a Bakelite board of 1 mm thickness was placed to separate axial wall heat conduction for local heat transfer measurement. The parameters involved are the Reynolds number Re, the Rotation number Ro, the Buoyancy parameter Gr/Re2, and the ratio of the heat transfer area Ap/Ac. The heat transfer results of radially rotating circular ducts based on per-passage and per-system were obtained.

AN EXPERIMENTAL AND NUMERICAL STUDY OF HEAT TRANSFER IN A SIMULATED COLLECTOR FOR A SOLAR DRYER

1993 ◽  
Vol 17 (2) ◽  
pp. 145-160
Author(s):  
P.H. Oosthuizen ◽  
A. Sheriff
Keyword(s):  
Heat Transfer ◽  
Numerical Study ◽  
Local Heat Transfer ◽  
Lower Surface ◽  
Local Heat ◽  
Electrical Heating ◽  
Temperature Profiles ◽  
Measured Temperature ◽  
Transfer Rates ◽  
Thermocouple Probe

Indirect passive solar crop dryers have the potential to considerably reduce the losses that presently occur during drying of some crops in many parts of the “developing” world. The performance so far achieved with such dryers has, however, not proved to be very satisfactory. If this performance is to be improved it is necessary to have an accurate computer model of such dryers to assist in their design. An important element is any dryer model is an accurate equation for the convective heat transfer in the collector. To assist in the development of such an equation, an experimental and numerical study of the collector heat transfer has been undertaken. In the experimental study, the collector was simulated by a 1m long by 1m wide channel with a gap of 4 cm between the upper and lower surfaces. The lower surface of the channel consisted of an aluminium plate with an electrical heating element, simulating the solar heating, bonded to its lower surface. Air was blown through this channel at a measured rate and the temperature profiles at various points along the channel were measured using a shielded thermocouple probe. Local heat transfer rates were then determined from these measured temperature profiles. In the numerical study, the parabolic forms of the governing equations were solved by a forward-marching finite difference procedure.

Heat Transfer in Separated, Reattached, and Redevelopment Regions Behind a Double Step at Entrance to a Flat Duct

1967 ◽  
Vol 89 (2) ◽  
pp. 163-167 ◽  
Author(s):  
E. G. Filetti ◽  
W. M. Kays
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Duct Flow ◽  
Double Step ◽  
Maximum Heat ◽  
Transfer Rates ◽  
Maximum Heat Transfer ◽  
Flow Cross

Experimental data are presented for local heat transfer rates near the entrance to a flat duct in which there is an abrupt symmetrical enlargement in flow cross section. Two enlargement area ratios are considered, and Reynolds numbers, based on duct hydraulic diameter, varied from 70,000 to 205,000. It is found that such a flow is characterized by a long stall on one side and a short stall on the other. Maximum heat transfer occurs in both cases at the point of reattachment, followed by a decay toward the values for fully developed duct flow. Empirical equations are given for the Nusselt number at the reattachment point, correlated as functions of duct Reynolds number and enlargement ratio.

Local and Average Heat Transfer Characteristics for a Disk Situated Perpendicular to a Uniform Flow

1985 ◽  
Vol 107 (2) ◽  
pp. 321-326 ◽  
Author(s):  
E. M. Sparrow ◽  
G. T. Geiger
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Stagnation Point ◽  
Radial Distance ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Local Heat Transfer Coefficient ◽  
Average Heat ◽  
Radial Profiles

Wind tunnel experiments were performed to determine both the average heat transfer coefficient and the radial distribution of the local heat transfer coefficient for a circular disk facing a uniform oncoming flow. The experiments covered the range of Reynolds numbers Re from 5000 to 50,000 and were performed using the naphthalene sublimation technique. To complement the experiments, an analysis incorporating both potential flow theory and boundary layer theory was used to predict the stagnation point heat transfer. The measured average Nusselt numbers definitively resolved a deep disparity between information from the literature and yielded the correlation Nu = 1.05 Pr0.36 Re1/2. The radial distributions of the local heat transfer coefficient were found to be congruent when they were normalized by Re1/2. Furthermore, the radial profiles showed that the local coefficient takes on its minimum value at the stagnation point and increases with increasing radial distance from the center of the disk. At the outer edge of the disk, the coefficient is more than twice as large as that at the stagnation point. The theoretical predictions of the stagnation point heat transfer exceeded the experimental values by about 6 percent. This overprediction is similar to that which occurs for cylinders and spheres in crossflow.

Three-Dimensional Natural Convection From Vertical Heated Plates With Adjoining Cool Surfaces

1992 ◽  
Vol 114 (1) ◽  
pp. 115-120 ◽  
Author(s):  
B. W. Webb ◽  
T. L. Bergman
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Control Volume ◽  
Three Dimensional ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Uniform Heat Flux ◽  
Infrared Thermal Imaging ◽  
Transfer Rates ◽  
Thermal Boundary Conditions

Natural convection in an enclosure with a uniform heat flux on two vertical surfaces and constant temperature at the adjoining walls has been investigated both experimentally and theoretically. The thermal boundary conditions and enclosure geometry render the buoyancy-induced flow and heat transfer inherently three dimensional. The experimental measurements include temperature distributions of the isoflux walls obtained using an infrared thermal imaging technique, while the three-dimensional equations governing conservation of mass, momentum, and energy were solved using a control volume-based finite difference scheme. Measurements and predictions are in good agreement and the model predictions reveal strongly three-dimensional flow in the enclosure, as well as high local heat transfer rates at the edges of the isoflux wall. Predicted average heat transfer rates were correlated over a range of the relevant dimensionless parameters.

scholarly journals Numerical heat transfer analysis of micro-scale jet-impingement cooling in a high-pressure turbine vane

2021 ◽  
Author(s):  
Karan Anand
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Heat Transfer Analysis ◽  
Transfer Rates ◽  
Numerical Heat Transfer ◽  
Turbine Vane ◽  
Single Jet

This research provides a computational analysis of heat transfer due to micro jet-impingement inside a gas turbine vane. A preliminary-parametric analysis of axisymmetric single jet was reported to better understand micro jet-impingement. In general, it was seen that as the Reynolds number increased the Nusselt number values increased. The jet to target spacing had a considerably lower impact on the heat transfer rates. Around 30% improvement was seen by reducing the diameter to half while changing the shape to an ellipse saw 20.8% improvement in Nusselt value. The numerical investigation was then followed by studying the heat transfer characteristics in a three-dimensional, actual-shaped turbine vane. Effects of jet inclination showed enhanced mixing and secondary heat transfer peaks. The effect of reducing the diameter of the jets to 0.125 mm yielded 55% heat transfer improvements compared to 0.51 mm; the tapering effect also enhanced the local heat transfer values as local velocities at jet exit increased.

Effect of Film Extraction on Impingement Heat Transfer Characteristics of Jet Arrays on Spherical-Dimpled Surfaces

2015 ◽  
Author(s):  
Xing Yang ◽  
Zhao Liu ◽  
Zhenping Feng
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Film Cooling ◽  
Coupling Effect ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Target Surface ◽  
Local Heat ◽  
Separation Distance ◽  
Plate Spacing

Detailed heat transfer distributions are numerically investigated on a multiple jet impingement target surface with staggered arrays of spherical dimples where coolant can be extracted through film holes for external film cooling. The three dimensional Reynolds-averaged Navier-Stokes analysis with SST k-ω turbulence model is conducted at jet Reynolds number from 15,000 to 35,000. The separation distance between the jet plate and the target surface varies from 3 to 5 jet diameters and two jet-induced crossflow schemes are included to be referred as large and small crossflow at one and two opposite exit openings correspondingly. Flow and heat transfer results for the dimpled target plate with three suction ratios of 2.5%, 5.0% and 12.0% are compared with those on dimpled surfaces without film holes. The results indicate the presence of film holes could alter the local heat transfer distributions, especially near the channel outlets where the crossflow level is the highest. The heat transfer enhancements by applying film holes to the dimpled surfaces is improved to different degrees at various suction ratios, and the enhancements depend on the coupling effect of impingement and channel flow, which is relevant to jet Reynolds number, jet-to-plate spacing and crossflow scheme.

Heat Transfer From a Cylinder in Crossflow With Transpiration Cooling

1963 ◽  
Vol 85 (2) ◽  
pp. 173-177 ◽  
Author(s):  
B. V. Johnson ◽  
J. P. Hartnett
Keyword(s):  
Heat Transfer ◽  
Stagnation Point ◽  
Heat Transfer Performance ◽  
Separated Flow ◽  
Local Heat Transfer ◽  
Flow Region ◽  
Local Heat ◽  
Stagnation Flow ◽  
Experimental Values ◽  
Good Agreement

Local heat-transfer measurements are reported for a transpiration-cooled cylinder in crossflow. The stagnation point measurements are found to be in good agreement with results from plane stagnation flow theory. In the laminar region beyond the stagnation point, the equivalent wedge method is found to predict heat-transfer performance within 10 percent of the experimental values. In the separated flow region the experimental results demonstrate that the transpiration process is still very effective in reducing the heat transfer.

Sign in / Sign up

Export Citation Format

Share Document