Separation and Stall of an Impulsively Started Elliptic Cylinder

1967 ◽  
Vol 34 (4) ◽  
pp. 823-828 ◽  
Author(s):  
Chang-Yi Wang
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Angle Of Attack ◽  
Elliptic Cylinder ◽  
Inviscid Flow ◽  
Reynolds Numbers ◽  
Thickness Ratio ◽  
Two Dimensional ◽  
Small Times ◽  
Weakly Dependent

Separation and stall of an impulsively started elliptic cylinder at an angle of attack are investigated through the method of inner and outer expansions. The assumptions are large Reynolds numbers and small times. The interactions between the boundary layer and the outer inviscid flow are taken into consideration. Uniformly valid solutions are obtained for general two-dimensional cylinders. The movements of the separation points on an elliptic cylinder are calculated. Stall is found to be strongly dependent on the thickness ratio and the angle of attack of the cylinder but to be weakly dependent on the Reynolds number.

On the impulsively started rotating sphere

1967 ◽  
Vol 27 (4) ◽  
pp. 779-788 ◽  
Author(s):  
K. E. Barrett
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Velocity Field ◽  
Reynolds Numbers ◽  
Time Dependent ◽  
Series Solutions ◽  
Rotating Sphere ◽  
Boundary Layer Equations ◽  
Small Times ◽  
3 Omega

The velocity field generated in a fluid of viscosity, v, by impulsively starting at time t = 0, a sphere of radius a spinning with angular velocity Ω about a diameter is described using a new expansion variable 2 √vt/r. It is first shown how the standard time-dependent boundary-layer equations can be modified to give series solutions satisfying all the boundary conditions. Next, that these new solutions are relevant when the Reynolds number R = a2Ω/v goes to infinity in such a way that $R^{\frac{1}{3}} \Omega t$ is large. Lastly, solutions are given, applicable at small times for non-zero Reynolds numbers. These last expansions show that the velocity components decay algebraically rather than exponentially at large distances.

scholarly journals Non-modal stability analysis of the boundary layer under solitary waves

2017 ◽  
Vol 836 ◽  
pp. 740-772 ◽  
Author(s):  
Joris C. G. Verschaeve ◽  
Geir K. Pedersen ◽  
Cameron Tropea
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Stability Analysis ◽  
Solitary Waves ◽  
Reynolds Numbers ◽  
Two Dimensional ◽  
Modal Theory ◽  
Critical Reynolds Numbers ◽  
Streamwise Streaks ◽  
The Stability

In the present work, a stability analysis of the bottom boundary layer under solitary waves based on energy bounds and non-modal theory is performed. The instability mechanism of this flow consists of a competition between streamwise streaks and two-dimensional perturbations. For lower Reynolds numbers and early times, streamwise streaks display larger amplification due to their quadratic dependence on the Reynolds number, whereas two-dimensional perturbations become dominant for larger Reynolds numbers and later times in the deceleration region of this flow, as the maximum amplification of two-dimensional perturbations grows exponentially with the Reynolds number. By means of the present findings, we can give some indications on the physical mechanism and on the interpretation of the results by direct numerical simulation in Vittori & Blondeaux (J. Fluid Mech., vol. 615, 2008, pp. 433–443) and Özdemir et al. (J. Fluid Mech., vol. 731, 2013, pp. 545–578) and by experiments in Sumer et al. (J. Fluid Mech., vol. 646, 2010, pp. 207–231). In addition, three critical Reynolds numbers can be defined for which the stability properties of the flow change. In particular, it is shown that this boundary layer changes from a monotonically stable to a non-monotonically stable flow at a Reynolds number of $Re_{\unicode[STIX]{x1D6FF}}=18$.

scholarly journals Plunging Airfoil: Reynolds Number and Angle of Attack Effects

Aerospace ◽  
2021 ◽  
Vol 8 (8) ◽  
pp. 216
Author(s):  
Emanuel A. R. Camacho ◽  
Fernando M. S. P. Neves ◽  
André R. R. Silva ◽  
Jorge M. M. Barata
Keyword(s):  
Reynolds Number ◽  
High Performance ◽  
Angle Of Attack ◽  
Systems Design ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Low Reynolds Numbers ◽  
Operational Conditions ◽  
Naca0012 Airfoil ◽  
The Mean

Natural flight has consistently been the wellspring of many creative minds, yet recreating the propulsive systems of natural flyers is quite hard and challenging. Regarding propulsive systems design, biomimetics offers a wide variety of solutions that can be applied at low Reynolds numbers, achieving high performance and maneuverability systems. The main goal of the current work is to computationally investigate the thrust-power intricacies while operating at different Reynolds numbers, reduced frequencies, nondimensional amplitudes, and mean angles of attack of the oscillatory motion of a NACA0012 airfoil. Simulations are performed utilizing a RANS (Reynolds Averaged Navier-Stokes) approach for a Reynolds number between 8.5×103 and 3.4×104, reduced frequencies within 1 and 5, and Strouhal numbers from 0.1 to 0.4. The influence of the mean angle-of-attack is also studied in the range of 0∘ to 10∘. The outcomes show ideal operational conditions for the diverse Reynolds numbers, and results regarding thrust-power correlations and the influence of the mean angle-of-attack on the aerodynamic coefficients and the propulsive efficiency are widely explored.

The Effect of Pulsed Blowing on the Boundary Layer of a Highly Loaded Low Pressure Turbine Blade

2013 ◽  
Author(s):  
Marion Mack ◽  
Roland Brachmanski ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Trailing Edge ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Highly Loaded

The performance of the low pressure turbine (LPT) can vary appreciably, because this component operates under a wide range of Reynolds numbers. At higher Reynolds numbers, mid and aft loaded profiles have the advantage that transition of suction side boundary layer happens further downstream than at front loaded profiles, resulting in lower profile loss. At lower Reynolds numbers, aft loading of the blade can mean that if a suction side separation exists, it may remain open up to the trailing edge. This is especially the case when blade lift is increased via increased pitch to chord ratio. There is a trend in research towards exploring the effect of coupling boundary layer control with highly loaded turbine blades, in order to maximize performance over the full relevant Reynolds number range. In an earlier work, pulsed blowing with fluidic oscillators was shown to be effective in reducing the extent of the separated flow region and to significantly decrease the profile losses caused by separation over a wide range of Reynolds numbers. These experiments were carried out in the High-Speed Cascade Wind Tunnel of the German Federal Armed Forces University Munich, Germany, which allows to capture the effects of pulsed blowing at engine relevant conditions. The assumed control mechanism was the triggering of boundary layer transition by excitation of the Tollmien-Schlichting waves. The current work aims to gain further insight into the effects of pulsed blowing. It investigates the effect of a highly efficient configuration of pulsed blowing at a frequency of 9.5 kHz on the boundary layer at a Reynolds number of 70000 and exit Mach number of 0.6. The boundary layer profiles were measured at five positions between peak Mach number and the trailing edge with hot wire anemometry and pneumatic probes. Experiments were conducted with and without actuation under steady as well as periodically unsteady inflow conditions. The results show the development of the boundary layer and its interaction with incoming wakes. It is shown that pulsed blowing accelerates transition over the separation bubble and drastically reduces the boundary layer thickness.

Essential Ingredients for the Computation of Steady and Unsteady Blade Boundary Layers

1991 ◽  
Vol 113 (4) ◽  
pp. 608-616 ◽  
Author(s):  
H. M. Jang ◽  
J. A. Ekaterinaris ◽  
M. F. Platzer ◽  
T. Cebeci
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Stokes Equations ◽  
Inviscid Flow ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Transitional Region ◽  
Low Reynolds Numbers ◽  
Flow Equations ◽  
Low Reynolds

Two methods are described for calculating pressure distributions and boundary layers on blades subjected to low Reynolds numbers and ramp-type motion. The first is based on an interactive scheme in which the inviscid flow is computed by a panel method and the boundary layer flow by an inverse method that makes use of the Hilbert integral to couple the solutions of the inviscid and viscous flow equations. The second method is based on the solution of the compressible Navier–Stokes equations with an embedded grid technique that permits accurate calculation of boundary layer flows. Studies for the Eppler-387 and NACA-0012 airfoils indicate that both methods can be used to calculate the behavior of unsteady blade boundary layers at low Reynolds numbers provided that the location of transition is computed with the en method and the transitional region is modeled properly.

Bifurcation Characteristics of Flows in Rectangular Sudden Expansion Channels

2005 ◽  
Author(s):  
Francine Battaglia ◽  
George Papadopoulos
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Critical Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Expansion Ratio ◽  
Sudden Expansion ◽  
Two Dimensional ◽  
Effective Expansion ◽  
Three Dimensional Simulations

The effect of three-dimensionality on low Reynolds number flows past a symmetric sudden expansion in a channel was investigated. The geometric expansion ratio of in the current study was 2:1 and the aspect ratio was 6:1. Both experimental velocity measurements and two- and three-dimensional simulations for the flow along the centerplane of the rectangular duct are presented for Reynolds numbers in the range of 150 to 600. Comparison of the two-dimensional simulations with the experiments revealed that the simulations fail to capture completely the total expansion effect on the flow, which couples both geometric and hydrodynamic effects. To properly do so requires the definition of an effective expansion ratio, which is the ratio of the downstream and upstream hydraulic diameters and is therefore a function of both the expansion and aspect ratios. When the two-dimensional geometry was consistent with the effective expansion ratio, the new results agreed well with the three-dimensional simulations and the experiments. Furthermore, in the range of Reynolds numbers investigated, the laminar flow through the expansion underwent a symmetry-breaking bifurcation. The critical Reynolds number evaluated from the experiments and the simulations was compared to other values reported in the literature. Overall, side-wall proximity was found to enhance flow stability, helping to sustain laminar flow symmetry to higher Reynolds numbers in comparison to nominally two-dimensional double-expansion geometries. Lastly, and most importantly, when the logarithm of the critical Reynolds number from all these studies was plotted against the reciprocal of the effective expansion ratio, a linear trend emerged that uniquely captured the bifurcation dynamics of all symmetric double-sided planar expansions.

scholarly journals Finite-amplitude steady waves in plane viscous shear flows

1985 ◽  
Vol 160 ◽  
pp. 281-295 ◽  
Author(s):  
F. A. Milinazzo ◽  
P. G. Saffman
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Stokes Equations ◽  
Reynolds Numbers ◽  
Finite Amplitude ◽  
Linear Instability ◽  
Navier Stokes ◽  
Unidirectional Flow ◽  
Viscous Shear ◽  
Finite Amplitude Waves

Computations of two-dimensional solutions of the Navier–Stokes equations are carried out for finite-amplitude waves on steady unidirectional flow. Several cases are considered. The numerical method employs pseudospectral techniques in the streamwise direction and finite differences on a stretched grid in the transverse direction, with matching to asymptotic solutions when unbounded. Earlier results for Poiseuille flow in a channel are re-obtained, except that attention is drawn to the dependence of the minimum Reynolds number on the physical constraint of constant flux or constant pressure gradient. Attempts to calculate waves in Couette flow by continuation in the velocity of a channel wall fail. The asymptotic suction boundary layer is shown to possess finite-amplitude waves at Reynolds numbers orders of magnitude less than the critical Reynolds number for linear instability. Waves in the Blasius boundary layer and unsteady Rayleigh profile are calculated by employing the artifice of adding a body force to cancel the spatial or temporal growth. The results are verified by comparison with perturbation analysis in the vicinity of the linear-instability critical Reynolds numbers.

Velocity and Pressure Measurements Along a Row of Confined Cylinders

2006 ◽  
Author(s):  
Barton L. Smith ◽  
Jack J. Stepan ◽  
Donald M. McEligot
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Symmetry Plane ◽  
Field Measurements ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Recirculation Region ◽  
Pressure Measurements ◽  
Layer Transition ◽  
Flow Experiments

The results of flow experiments performed in a cylinder array designed to mimic a VHTR Nuclear Plant lower plenum design are presented. Pressure drop and velocity field measurements were made. Based on these measurements, five regimes of behavior are identified that are found to depend on Reynolds number. It is found that the recirculation region behind the cylinders is shorter than that of half cylinders placed on the wall representing the symmetry plane. Unlike a single cylinder, the separation point is found to always be on the rear of the cylinders, even at very low Reynolds number. Boundary layer transition is found to occur at much lower Reynolds numbers than previously reported.

The boundary layer in crossed-fields m.h.d.

1966 ◽  
Vol 25 (2) ◽  
pp. 229-240 ◽  
Author(s):  
W. R. Sears
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Flat Plate ◽  
Flow Problem ◽  
Inviscid Flow ◽  
Magnetic Reynolds Number ◽  
Large Reynolds Number ◽  
Zero Values ◽  
Plate Solution ◽  
A Current

This study of the boundary layer of steady, incompressible, plane, crossed-fields m.h.d. flow at large Reynolds numberReand magnetic Reynolds numberRmbegins with a review of Hartmann's case, where a boundary layer occurs whose thickness is proportional to (Re Rm)−½. Following this clue, it is shown that in general the boundary layer is a ‘local Hartmann boundary layer’. Its profiles are always exponential and it is determined completely by local quantities. The skin friction and the total electric current in the layer are proportional to the square root of the magnetic Prandtl number, i.e. to (Rm/Re)½. Thus the exterior-flow problem, the solution of which precedes a boundary-layer solution, generally involves a current sheet at the fluid-solid interface.This inviscid-flow problem becomes tractable if (Rm/Re)½is small enough to permit a linearized solution. The flow field about a flat plate at zero incidence is calculated in this approximation. It is pointed out that the thin-cylinder solutions of Sears & Resler (1959), which pertain toRm/Re= 0, can immediately be extended to small, non-zero values of this parameter by linear combination with this flat-plate solution.

Two-dimensional global low-frequency oscillations in a separating boundary-layer flow

2008 ◽  
Vol 614 ◽  
pp. 315-327 ◽  
Author(s):  
UWE EHRENSTEIN ◽  
FRANÇOIS GALLAIRE
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Perturbation Analysis ◽  
Boundary Layer Flow ◽  
Stokes Equations ◽  
Low Frequency ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Optimal Perturbation ◽  
Layer Flow

A separated boundary-layer flow at the rear of a bump is considered. Two-dimensional equilibrium stationary states of the Navier–Stokes equations are determined using a nonlinear continuation procedure varying the bump height as well as the Reynolds number. A global instability analysis of the steady states is performed by computing two-dimensional temporal modes. The onset of instability is shown to be characterized by a family of modes with localized structures around the reattachment point becoming almost simultaneously unstable. The optimal perturbation analysis, by projecting the initial disturbance on the set of temporal eigenmodes, reveals that the non-normal modes are able to describe localized initial perturbations associated with the large transient energy growth. At larger time a global low-frequency oscillation is found, accompanied by a periodic regeneration of the flow perturbation inside the bubble, as the consequence of non-normal cancellation of modes. The initial condition provided by the optimal perturbation analysis is applied to Navier–Stokes time integration and is shown to trigger the nonlinear ‘flapping’ typical of separation bubbles. It is possible to follow the stationary equilibrium state on increasing the Reynolds number far beyond instability, ruling out for the present flow case the hypothesis of some authors that topological flow changes are responsible for the ‘flapping’.

Sign in / Sign up

Export Citation Format

Share Document