Dye Mixing Effects on Photocatalytic Water Splitting Activity on Dye-Modified KTaO3 Catalyst

2010 ◽  
Vol 132 (2) ◽  
Author(s):  
Hidehisa Hagiwara ◽  
Hiroshige Matsumoto ◽  
Tatsumi Ishihara

Dye mixing effects on water splitting activity of KTaO3 photocatalyst modified by various porphyrinoids was investigated. Photocatalytic activity of dye-modified KTaO3 catalyst is greatly improved by mixing various porphyrinoids, in which transition metals such as Cr, Fe, and Co are used as central metal. Pentametylene bis[4-(10, 15, 20-triphenyl porphine-5-yl) benzoate]-dizinc(II) (Zn-TPP dimer) showed positive effect on photocatalytic activity, and H2 and O2 formation rates are 365 μmol g−cat.−1 h−1 and 152 μmol g−cat.−1 h−1, respectively. On the other hand, the combination of chloroprotoporphyrinato iron (III) (chlorohemin) with Cr-phthalocyanine (CrPc) is the most effective for increasing water splitting activity, and the formation rates of H2 and O2 are 2.12 mmol g−cat.−1 h−1 and 1.11 mmol g−cat.−1 h−1, respectively. Energy conversion efficiency of this photocatalyst is estimated to be approximately 0.05%. From X-ray photoelectron spectroscopy measurement and cyclic voltammetry of organic dyes, it is suggested that the electronic state of the dye mixture is modified compared with that of a single dye. Energy transfer between mixing dyes is observed in the fluorescence spectra of dye-modified KTaO3 photocatalysts. Recombination of photoexited charge in KTaO3 is clearly suppressed by dye mixing, thus improvement of photocatalytic activity is attributed to the lengthening of excitation lifetime. This study reveals that mixing porphyrinoid dyes is an effective method for increasing water splitting activity of dye-modified KTaO3 photocatalysts.

2014 ◽  
Vol 2014 ◽  
pp. 1-6
Author(s):  
M.-J. Zhou ◽  
N. Zhang ◽  
Z. H. Hou

In the present work, graphene-WO3nanowire clusters were synthesizedviaa facile hydrothermal method. The obtained graphene-WO3nanowire clusters were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, and ultraviolet-visible diffuse reflectance spectroscopy (DRS) techniques. The photocatalytic oxygen (O2) evolution properties of the as-synthesized samples were investigated by measuring the amount of evolved O2from water splitting. The graphene-WO3nanowire clusters exhibited enhanced performance compared to pure WO3nanowire clusters for O2evolution. The amount of evolved O2from water splitting after 8 h for the graphene-WO3nanowire clusters isca.0.345 mmol/L, which is more than 1.9 times as much as that of the pure WO3nanowire clusters (ca.0.175 mmol/L). The high photocatalytic activity of the graphene-WO3nanowire clusters was attributed to a high charge transfer rate in the presence of graphene.


2017 ◽  
Vol 76 (8) ◽  
pp. 2120-2132 ◽  
Author(s):  
Q. Song ◽  
L. Li ◽  
N. Zhuo ◽  
H. N. Zhang ◽  
X. Chen ◽  
...  

Taking cetyltrimethylammonium bromide (CTAB) as the template and using TiO2 as the substrate, coral-globular-like composite Ag/TiO2-SnO2 (CTAB) was successfully synthesized by the sol–gel combined with a temperature-programmed treatment method. X-ray diffraction, scanning electron microscopy (SEM), UV–vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, SEM combined with X-ray energy dispersive spectroscopy, and N2 adsorption–desorption tests were employed to characterize samples' crystalline phase, chemical composition, morphology and surface physicochemical properties. Results showed that composites not only had TiO2 anatase structure, but also had some generated SnTiO4, and the silver species was metallic Ag0. Ag/TiO2-SnO2 (CTAB) possessed a coral-globular-like structure with nanosheets in large quantities. The photocatalytic activity of Ag/TiO2-SnO2 (CTAB) had studied by degrading organic dyes under multi-modes, mainly using rhodamine B as the model molecule. Results showed that the coral-globular-like Ag/TiO2-SnO2 (CTAB) was higher photocatalytic activity than that of commercial TiO2, Ag/TiO2-SnO2, TiO2-SnO2 (CTAB), and TiO2-SnO2 under ultraviolet light irradiation. Moreover, Ag/TiO2-SnO2 (CTAB) composite can significantly affect the photocatalytic degradation under multi-modes including UV light, visible light, simulated solar light and microwave-assisted irradiation. Meanwhile, the photocatalytic activity of Ag/TiO2-SnO2 (CTAB) was maintained even after three cycles, indicating that the catalyst had good usability.


Separations ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 25
Author(s):  
Chukwuka Bethel Anucha ◽  
Ilknur Altin ◽  
Emin Bacaksız ◽  
Tayfur Kucukomeroglu ◽  
Masho Hilawie Belay ◽  
...  

Abatement of contaminants of emerging concerns (CECs) in water sources has been widely studied employing TiO2 based heterogeneous photocatalysis. However, low quantum energy yield among other limitations of titania has led to its modification with other semiconductor materials for improved photocatalytic activity. In this work, a 0.05 wt.% CuWO4 over TiO2 was prepared as a powder composite. Each component part synthesized via the sol-gel method for TiO2, and CuWO4 by co-precipitation assisted hydrothermal method from precursor salts, underwent gentle mechanical agitation. Homogenization of the nanopowder precursors was performed by zirconia ball milling for 2 h. The final material was obtained after annealing at 500 °C for 3.5 h. Structural and morphological characterization of the synthesized material has been achieved employing X-ray diffraction (XRD), Fourier transform infra-red (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) N2 adsorption–desorption analysis, Scanning electron microscopy-coupled Energy dispersive X-ray spectroscopy (SEM-EDS), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectroscopy (UV-vis DRS) for optical characterization. The 0.05 wt.% CuWO4-TiO2 catalyst was investigated for its photocatalytic activity over carbamazepine (CBZ), achieving a degradation of almost 100% after 2 h irradiation. A comparison with pure TiO2 prepared under those same conditions was made. The effect of pH, chemical scavengers, H2O2 as well as contaminant ion effects (anions, cations), and humic acid (HA) was investigated, and their related influences on the photocatalyst efficiency towards CBZ degradation highlighted accordingly.


2020 ◽  
Vol 2020 ◽  
pp. 1-9 ◽  
Author(s):  
N. Cruz-González ◽  
O. Calzadilla ◽  
J. Roque ◽  
F. Chalé-Lara ◽  
J. K. Olarte ◽  
...  

In the last decade, the urgent need to environmental protection has promoted the development of new materials with potential applications to remediate air and polluted water. In this work, the effect of the TiO2 thin layer over MoS2 material in photocatalytic activity is reported. We prepared different heterostructures, using a combination of electrospinning, solvothermal, and spin-coating techniques. The properties of the samples were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), X-ray diffraction (XRD), nitrogen adsorption-desorption isotherms, UV-Vis diffuse reflectance spectroscopy (UV-Vis-DRS), and X-ray photoelectron spectroscopy (XPS). The adsorption and photocatalytic activity were evaluated by discoloration of rhodamine B solution. The TiO2-MoS2/TiO2 heterostructure presented three optical absorption edges at 1.3 eV, 2.28 eV, and 3.23 eV. The high adsorption capacity of MoS2 was eliminated with the addition of TiO2 thin film. The samples show high photocatalytic activity in the visible-IR light spectrum.


2015 ◽  
Vol 827 ◽  
pp. 19-24 ◽  
Author(s):  
Nur Afifah ◽  
Nadia Febiana Djaja ◽  
Rosari Saleh

In this study, the photocatalytic activity of pure Fe- doped ZnO and Fe- doped ZnO/Montmorillonite nanocomposite has been investigated for the degradation of malachite green under UV light irradiation. Both photocatalysts were synthesized using co-precipitation method and characterized by X-ray diffraction, energy dispersive X-ray spectroscopy, Fourier-transform infrared absorption, and electron spin resonance. The results showed that the photocatalytic efficiency is better in the presence of montmorillonite compared to pure Fe- doped ZnO. To detect the possible reactive species involved in degradation of organic dyes control experiments with introducing scavengers into the solution of organic dyes were carried out. It is found that electron plays an important role in the degradation of malachite green.


2011 ◽  
Vol 383-390 ◽  
pp. 3188-3191
Author(s):  
Han Jie Huang ◽  
Wen Long She ◽  
Ling Wen Yang ◽  
Hai Peng Huang

A visible-light-responsive TiO2-xNx photocatalyst was prepared by a very simple method. Ammonia solution was used as nitrogen resource in this paper. The TiO2-xNx photocatalyst was characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), UV-Vis diffuse reflection spectra (DRS), and X-ray photoelectron spectroscopy (XPS). The ethylene was selected as a target pollutant under visible light excitation to evaluate the activity of this photocatalyst. The new prepared TiO2-xNx photocatalyst with strong photocatalytic activity under visible light irradiation was demonstrated in the experiment.


2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Huang Liu ◽  
Yanhua Zhang ◽  
Hongtao Yang ◽  
Wei Xiao ◽  
Lanlan Sun

Using the common natural cellulose substance (filter paper) and triblock copolymer (Pluronic P123) micelles as dual templates, porous titania nanotubes with enhanced photocatalytic activity have been successfully synthesized through sol-gel methods. Firstly, P123 micelles were adsorbed onto the surfaces of cellulose nanofibers of filter paper, followed by hydrolysis and condensation of tetrabutyl titanate around these micelles to form titania layer. After calcination to remove the organic templates, hierarchical titania nanotubes with pores in the walls were obtained. The sample was characterized by X-ray diffraction pattern (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen adsorption/desorption, Fourier Transform Infrared Spectroscopy (FT-IR), Ultraviolet-Visible Diffuse Reflectance Spectroscopy (UV-Vis DRS), and X-ray photoelectron spectroscopy (XPS). As compared with commercial P25 catalyst, the porous titania nanotubes prepared by this method displayed significantly enhanced photocatalytic activity for degrading methyl orange under UV irradiation. Within 10 minutes, the porous titania nanotubes are able to degrade over 70% of the original MO, while the value for the commercial Degussa P25 is only about 33%.


2012 ◽  
Vol 2012 ◽  
pp. 1-12 ◽  
Author(s):  
Jiang Zhang ◽  
Zheng-Hong Huang ◽  
Yong Xu ◽  
Feiyu Kang

The iodine-doped Bi2WO6(I-BWO) photocatalyst was prepared via a hydrothermal method using potassium iodide as the source of iodine. The samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM) and selected area electron diffraction (SAED), X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) spectroscopy. The photocatalytic activity of I-BWO for the degradation of rhodamine B (RhB) was higher than that of pure BWO and I2-BWO regardless of visible light (>420 nm) or ultraviolet light (<400 nm) irradiation. The results of DRS analysis showed that the I-BWO and I2-BWO catalysts had narrower band gaps. XPS analysis proved that the multivalent iodine species including I0and were coadsorbed on the defect surface of Bi2WO6in I-BWO. The enhanced PL intensity revealed that a large number of defects of oxygen vacancies were formed by the doping of iodine. The enhanced photocatalytic activity of I-BWO for degradation of RhB was caused by the synergetic effect of a small crystalline size, a narrow band gap, and plenty of oxygen vacancies.


Author(s):  
Irwing M. Ramírez-Sánchez ◽  
Erick R. Bandala

Iron Doped TiO2 nanoparticles (Fe-TiO2) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO2 physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe3+) was in the lattice of TiO2 and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe3+ concentration played a key role in the photocatalytic generation of hydroxyl radical (&bull;OH) and estriol (E3) degradation. Fe-TiO2 materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO2) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO2 (zero-iron TiO2) and Aeroxide&reg; TiO2 P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO2 under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.


Author(s):  
Thế Luân Nguyễn ◽  
Tiến Khoa Lê ◽  
Châu Ngọc Hoàng ◽  
Hữu Khánh Hưng Nguyễn ◽  
Thị Kiều Xuân Huỳnh

The Cu doped ZnO photocatalysts were prepared on ZnO substrate modified with copper nitrate by thermal shock method with different ratio % molar Cu : Zn = 0.3, 0.5, 1.0, 2.0 and 5.0 in order to study the impacts of copper content on the photocatalytic activity of ZnO under both UV and Vis light irradiation. The crystal structure, morphology bulk and surface were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activities were studied via time-dependent degradation of methylene blue in aqueous solution. The results exhibit that crystal structure and morphology of Cu doped ZnO photocatalysts is not modified significally than ZnO original but surface charateristicschanged greatly. The photocatalyst was doped with copper content under 2% showed formation of Cu species. These samples perform photocatalytic activity higher than ZnO. The CuNZO-0.05-500 had the highest rate constants for methylene blue degradation (kUV = 6,901 h-1, kVIS = 0,224 h-1), which are about 2.2 times and 1.3 times higher than unmodified ZnO under UV light and Vis light, respectively. However, the CuNZO-5.0-500 which had the formation of CuO phase and unchangeable ZnO's surface has photocatalytic activity similar to pure ZnO.


Sign in / Sign up

Export Citation Format

Share Document