Development of a Real-Time NOx Prediction Model Based on Heat Release Analysis in a Direct-Injection Diesel Engine

2013 ◽  
Vol 136 (3) ◽  
Author(s):  
Dong Wang ◽  
Chao Zhang
Keyword(s):  
Diesel Engine ◽  
Prediction Model ◽  
Heat Release ◽  
Real Time ◽  
Heat Release Rate ◽  
Release Rate ◽  
Direct Injection ◽  
Operating Conditions ◽  
Nox Emissions ◽  
Direct Injection Diesel Engine

A prediction model, which describes linear relationship between the nitrogen oxides (NOx) emissions and the in-cylinder heat release rate in a direct-injection diesel engine, was developed through numerical simulations. A modified KIVA-3 V code was used to calculate NOx formations and to conduct heat release analyses in a direct-injection diesel engine under different operating conditions. The numerical simulation results indicated that the NOx formation amount was related to both the magnitude and the timing of the peak heat release rate in each engine cycle. Based on the above observations, a control-oriented dynamic NOx model was constructed and then implemented into a feedback emission control system on a small diesel engine. A new parameter—combustion acceleration—was proposed in this research to describe the intensity of the premixed combustion. Experimental work was also conducted to measure the real-time in-cylinder pressure at each crank-angle when the engine was running and the heat release rate was calculated instantaneously to control an exhaust gas recirculation (EGR) valve. The experimental results showed that the proposed NOx prediction model was effective in controlling NOx emissions under high rpm conditions.

Determination of the Start and End of Combustion in a Direct Injection Diesel Engine Using the Apparent Heat Release Rate

2017 ◽  
Author(s):  
Joseph Gerard T. Reyes ◽  
Edwin N. Quiros
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Direct Injection ◽  
Injection Timing ◽  
Fuel Injector ◽  
Direct Injection Diesel Engine ◽  
Crank Angle ◽  
Start Of Combustion

The combustion duration in an internal combustion engine is the period bounded by the engine crank angles known as the start of combustion (SOC) and end of combustion (EOC), respectively. This period is essential in analysis of combustion for the such as the production of exhaust emissions. For compression-ignition engines, such as diesel engines, several approaches were developed in order to approximate the crank angle for the start of combustion. These approaches utilized the curves of measured in-cylinder pressures and determining by inspection the crank angle where the slope is steep following a minimum value, indicating that combustion has begun. These pressure data may also be utilized together with the corresponding cylinder volumes to generate the apparent heat release rate (AHRR), which shows the trend of heat transfer of the gases enclosed in the engine cylinder. The start of combustion is then determined at the point where the value of the AHRR is minimum and followed by a rapid increase in value, whereas the EOC is at the crank angle where the AHRR attains a flat slope prior to the exhaust stroke of the engine. To verify the location of the SOC, injection line pressures and fuel injection timing are also used. This method was applied in an engine test bench using a four-cylinder common-rail direct injection diesel engine with a pressure transducer installed in the first cylinder. Injector line pressures and fuel injector voltage signals per engine cycle were also recorded and plotted. By analyzing the trends of this curves in line with the generated AHRR curves, the SOC may be readily determined.

scholarly journals Effect of Various Supercharger Boost Pressure to in-Cylinder Pressure and Heat Release Rate Characteristics of Direct Injection Diesel Engine at Various Engine Rotation

2019 ◽  
Vol 130 ◽  
pp. 01036
Author(s):  
Willyanto Anggono ◽  
Wataru Ikoma ◽  
Haoyu Chen ◽  
Zhiyuan Liu ◽  
Mitsuhisa Ichiyanagi ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Power Efficiency ◽  
Direct Injection ◽  
Boost Pressure ◽  
Cylinder Pressure ◽  
Stroke Length ◽  
Direct Injection Diesel Engine

The diesel engines are superior in terms of power efficiency and fuel economy compared to gasoline engines. In order to optimize the performance of direct injection diesel engine, the effect of various intake pressure (boost pressure) from supercharging direct injection diesel engine was studied at various engine rotation. A single cylinder direct injection diesel engine was used in this experiment. The bore diameter of the engine used was set to 85 mm, the stroke length was set to 96.9 mm, and the compression ratio was set to 16.3. The variation of engine rotation started from 800 rpm to 2 000 rpm with 400 rpm increment. The variation of boost pressure is bounded from 0 kPa boost pressure (naturally aspirated) to the maximum of 60 kPa boost pressure with 20 kPa boost pressure increment. The performance of the engine is evaluated in terms of in-cylinder pressure and heat release rate as the most important performance characteristics of the diesel engine. The in-cylinder pressure and heat release rate of direct injection diesel engine are increased with the elevation of boost pressure at various engine rotation. The raise of engine rotation resulted in the decrease of maximum in-cylinder pressure and heat release rate.

Comparative Performance, Emission, and Combustion Characteristics of Rice-Bran Oil and Its Biodiesel in a Transportation Diesel Engine

2010 ◽  
Vol 132 (6) ◽  
Author(s):  
Avinash Kumar Agarwal ◽  
Atul Dhar
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Rice Bran ◽  
Heat Release Rate ◽  
Release Rate ◽  
Rice Bran Oil ◽  
Direct Injection ◽  
Pressure Rise ◽  
Combustion Characteristics ◽  
Comparative Performance

The methyl esters of vegetable oils known as biodiesel are becoming increasingly popular because of their low environmental impact and potential as a green alternative fuel for diesel engines. Methyl ester of rice-bran oil (RBOME) is prepared through the process of transesterification. In the present investigation, experiments have been carried out to examine the performance, emission, and combustion characteristics of a direct-injection transportation diesel engine running with diesel, 20% blend of rice-bran oil (RBO), and 20% blend of RBOME with mineral diesel. A four-stroke, four-cylinder, direct-injection transportation diesel engine (MDI 3000) was instrumented for the measurement of the engine performance, emissions, in-cylinder pressure-crank angle history, rate of pressure rise, and other important combustion parameters such as instantaneous heat release rate, cumulative heat release rate, mass fraction burned, etc. A careful analysis of the performance, emissions, combustion, and heat release parameters has been carried out. HC, CO, and smoke emissions for RBO and RBOME blends were lower than mineral diesel while NOx emissions were almost similar and brake specific fuel consumption (BSFC) was slightly higher than mineral diesel. Combustion characteristics were quite similar for the three fuels.

Combustion Characteristics of Rice Bran Oil Derived Biodiesel in a Transportation Diesel Engine

2006 ◽  
Author(s):  
Shailendra Sinha ◽  
Avinash Kumar Agarwal
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Rice Bran ◽  
Heat Release Rate ◽  
Release Rate ◽  
Rice Bran Oil ◽  
Direct Injection ◽  
Pressure Rise ◽  
Combustion Characteristics ◽  
Experimental Investigations

The methyl esters of vegetable oils, known as biodiesel are becoming increasingly popular because of their low environmental impact and potential as a green alternative fuel for diesel engines. They do not require significant modification in existing engine hardware. Methyl ester of rice bran oil (ROME) is prepared through the process of transesterification. Previous research has shown that ROME has comparable performance, lower bsfc in comparison to diesel. There was reduction in the emissions of CO, HC, and smoke but NOx emissions increased. In the present research, experimental investigations have been carried out to examine the combustion characteristics of a direct injection transportation diesel engine running with diesel, and 20% blend of ROME with diesel. A four-stroke, four-cylinder, direct-injection transportation diesel engine (MDI 3000) was fully instrumented for the measurement of combustion pressure, rate of pressure rise and other combustion parameters such as instantaneous heat release rate, cumulative heat release rate, mass fraction burned etc. Tests were performed at different loads ranging from no load to 100%, at constant engine speed. No engine hardware modification was carried out for the present study. A careful analysis of combustion and heat release parameters has been carried out, which gives precise information about the in-cylinder combustion of rice bran oil based biodiesel vis-a`-vis mineral diesel.

Fundamental Study of Diesel-Piloted Natural Gas Direct Injection Under Different Operating Conditions

2019 ◽  
Vol 141 (9) ◽  
Author(s):  
Georg Fink ◽  
Michael Jud ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Soot Formation ◽  
Direct Injection ◽  
Combustion Process ◽  
Operating Conditions ◽  
Gas Jet ◽  
Ignition And Combustion

Natural gas as an alternative fuel in engine applications substantially reduces both pollutant and greenhouse gas emissions. High pressure dual fuel (HPDF) direct injection of natural gas and diesel pilot has the potential to minimize methane slip from gas engines and increase the fuel flexibility, while retaining the high efficiency of a diesel engine. Speed and load variations as well as various strategies for emission reduction entail a wide range of different operating conditions. The influence of these operating conditions on the ignition and combustion process is investigated on a rapid compression expansion machine (RCEM). By combining simultaneous shadowgraphy (SG) and OH* imaging with heat release rate analysis, an improved understanding of the ignition and combustion process is established. At high temperatures and pressures, the reduced pilot ignition delay and lift-off length minimize the effect of natural gas jet entrainment on pilot mixture formation. A simple geometrical constraint was found to reflect the susceptibility for misfiring. At the same time, natural gas ignition is delayed by the early pilot ignition close to the injector tip. The shape of heat release is only marginally affected by the operating conditions and mainly determined by the degree of premixing at the time of gas jet ignition. Luminescence from the sooting natural gas flame is generally only detected after the flame extends across the whole gas jet at peak heat release rate. Termination of gas injection at this time was confirmed to effectively suppress soot formation, while a strongly sooting pilot seems to intensify soot formation within the natural gas jet.

Fundamental Study of Diesel-Piloted Natural Gas Direct Injection Under Different Operating Conditions

2018 ◽  
Author(s):  
Georg Fink ◽  
Michael Jud ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Soot Formation ◽  
Direct Injection ◽  
Combustion Process ◽  
Operating Conditions ◽  
Gas Jet ◽  
Ignition And Combustion

Natural gas as an alternative fuel in engine applications substantially reduces both pollutant and greenhouse gas emissions. High pressure dual fuel direct injection of natural gas and Diesel pilot has the potential to minimize methane slip from gas engines and increase the fuel flexibility, while retaining the high efficiency of a Diesel engine. Speed and load variations as well as various strategies for emission reduction entail a wide range of different operating conditions. The influence of these operating conditions on the ignition and combustion process is investigated on a rapid compression expansion machine. By combining simultaneous Shadowgraphy and OH* imaging with heat release rate analysis, an improved understanding of the ignition and combustion process is established. At high temperatures and pressures the reduced pilot ignition delay and lift-off length minimize the effect of natural gas jet entrainment on pilot mixture formation. A simple geometrical constraint was found to reflect the susceptibility for misfiring. At the same time natural gas ignition is delayed by the early pilot ignition close to the injector tip. The shape of heat release is only marginally affected by the operating conditions and mainly determined by the degree of premixing at the time of gas jet ignition. Luminescence from the sooting natural gas flame is generally only detected after the flame extends across the whole gas jet at peak heat release rate. Termination of gas injection at this time was confirmed to effectively suppress soot formation, while a strongly sooting pilot seems to intensify soot formation within the natural gas jet.

scholarly journals Study on the Influence of EGR on the Combustion Performance of Biofuel Diesel at Different Ambient Simulated Pressures

2021 ◽  
Vol 13 (14) ◽  
pp. 7862
Author(s):  
Zefei Tan ◽  
Jun Wang ◽  
Wengang Chen ◽  
Lizhong Shen ◽  
Yuhua Bi
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Atmospheric Pressure ◽  
Volume Fraction ◽  
Nox Emissions ◽  
Power Performance ◽  
Combustion Pressure ◽  
Co Emission

In order to explore the influence of EGR at different altitudes on the performance of biofuel diesel engines, a comparative experimental study is conducted with the biodiesel–ethanol–diesel B15E5 (biodiesel with 15% volume fraction, ethanol with 5% volume fraction and diesel with 80% volume fraction) mixed fuel at different EGR rate and different atmospheric pressure. The experimental results show that diesel engine power performance and economy goes up with the increase of atmospheric pressure, and it decreases with the increase of EGR rate. At 2200 rpm, the improvement range of medium and high diesel engine load is 1.5–6.8%, and that of 1800 rpm is 2.8–11.7%. At the same atmospheric pressure, with the increase of EGR rate, the power and economy turn worse. The peak combustion pressure and heat release rate both increased with the increase of the atmospheric pressure at full load. At the same atmospheric pressure, peak combustion pressure and peak heat release rate fall with the increase of EGR rate. At part load, firstly, smoke emissions fall with the increase of the load and then rise. As the atmospheric pressure goes up, the smoke emissions show a downward trend, with a decline of 6.6–40%, while the NOx emissions show a rising trend, with an increase of 1.2–8.5%. At the same atmospheric pressure, the smoke emission increase with the increase of EGR rate by 9–12.5%, and the NOx emissions increase with the decrease of EGR rate by 2.5–6.8%. The HC and CO Emissions decrease with the increase of atmospheric pressure. HC emission decreases by 9.3–19.1%, and CO emission decreases by 2.9–16.6%. At the same atmospheric pressure, the HC emission decreases with the increase of the EGR rate by 3.3–4.5% at medium and high loads, and the CO emission increases with the EGR rate by 3.1–4.5%.

Combustion and Emission Characteristics of Dual Fuel Engine for Different Parameters

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Jianjun Zhu ◽  
Peng Li ◽  
Yufeng Xie ◽  
Xin Geng
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Compression Ratio ◽  
Release Rate ◽  
Emission Characteristics ◽  
Soot Emission ◽  
Cylinder Pressure ◽  
Fuel Delivery ◽  
Soot Emissions

The effects of compression ratio and fuel delivery advance angle on the combustion and emission characteristics of premixed methanol charge induced ignition by Fischer Tropsch diesel engine were investigated using a CY25TQ diesel engine. In the process of reducing the compression ratio from 16.9 to 15.4, the starting point of combustion is fluctuating, the peak of in-cylinder pressure and the maximum pressure increase rate decrease by 44.5% and 37.7% respectively. The peak instantaneous heat release rate increases by 54.4%. HC and CO emissions are on a rising trend. NOx and soot emissions were greatly decreased. The soot emission has the biggest drop of 50%. Reducing the fuel delivery advance angle will make the peak of in-cylinder pressure and the peak of pressure rise rate increase while the peak of heat release rate decreases. The soot emission is negatively correlated with the fuel delivery advance angle. When the fuel delivery advance angle is 16° CA, the soot emissions increased the most by 130%.

Sign in / Sign up

Export Citation Format

Share Document