Flow and Heat Transfer of Nanoencapsulated Phase Change Material Slurry Past a Unconfined Square Cylinder

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Hamid Reza Seyf ◽  
Michael R. Wilson ◽  
Yuwen Zhang ◽  
H. B. Ma
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Phase Change ◽  
Melting Temperature ◽  
Base Fluid ◽  
Volume Fraction ◽  
Pure Water ◽  
Reynolds Numbers ◽  
Square Cylinder ◽  
Change Material

Numerical solution is carried out to analyze the effect of nanoencapsulated phase change material (NEPCM) slurry on forced convection heat transfer of steady laminar flow past an isothermal square cylinder. The base fluid is water while the NEPCM particles material is n-octadecane with an average diameter of 100 nm. A parametric study was performed for different volume fraction of nanoparticles ranging from 0% to 30%, two melting temperature ranges, i.e., 10 K and 20 K, and different inlet Reynolds numbers ranging from 15 to 45. The governing equations of flow and energy are solved simultaneously using a finite volume method (FVM) on collocated grid arrangement. It was found that for both NEPCM slurry and pure water, local and average heat transfer coefficients increases with increasing Reynolds number. The results of heat transfer characteristics of slurry flow over the square cylinder showed remarkable enhancement relative to that of the base fluid. The enhancement intensifies for higher particle volume concentrations and higher Reynolds numbers. However, utilizing the slurry can cause higher shear stress on the wall due to higher viscosity of mixture compared to the pure water. The melting temperature range of NEPCM particles has slight effect on heat transfer, although with increasing volume fraction and Reynolds number, lower melting range leads to higher heat transfer coefficient.

A Comparative Study on Thermal-Hydraulic Performance of Different Non-Newtonian Nanofluids Through an Elliptical Annulus

2021 ◽  
Vol 13 (5) ◽  
Author(s):  
Prabhakar Zainith ◽  
Niraj Kumar Mishra
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Base Fluid ◽  
Volume Fraction ◽  
Flow Behavior ◽  
Pure Water ◽  
Reynolds Numbers ◽  
Power Law Model ◽  
Laminar Condition

Abstract This paper presents a numerical investigation on heat transfer and flow behavior for non-Newtonian nanofluids with different nanoparticles (Al2O3 and CuO) and carboxymethyl cellulose (CMC) with water as a base fluid. The analysis has been carried out in an elliptical tube. Power-law model is adopted to depict the non-Newtonian nature of nanofluid. The present study has been done with a range of nanosized particles 0–4% by volume, and the variation of Reynolds number is kept under the laminar condition. The physical model covers two concentric tubes used to create an annular space. The effects of volume fraction, particle type, and base fluid have been investigated at different Reynolds numbers numerically. Also, the effect of pressure and heat transfer coefficient on the flow behavior of non-Newtonian nanofluids is analyzed. The results concluded that Al2O3 particles showed 219% and CuO particles give 195% higher heat transfer coefficient as compared with pure water.

Quantitative Experimental Study of SiO2-Water Nanofluids on Backward-Facing Step Flow under Low Reynolds Number

2018 ◽  
Vol 916 ◽  
pp. 221-225
Author(s):  
Ji Zu Lv ◽  
Liang Yu Li ◽  
Cheng Zhi Hu ◽  
Min Li Bai ◽  
Sheng Nan Chang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Volume Fraction ◽  
Pure Water ◽  
Experimental Studies ◽  
Flow Characteristics ◽  
Thermal Engineering ◽  
Heat Transfer Medium ◽  
Step Flow

Nanofluids is an innovative study of nanotechnology applied to the traditional field of thermal engineering. It refers to the metal or non-metallic nanopowder was dispersed into water, alcohol, oil and other traditional heat transfer medium, to prepared as a new heat transfer medium with high thermal conductivity. The role of nanofluids in strengthening heat transfer has been confirmed by a large number of experimental studies. Its heat transfer mechanism is mainly divided into two aspects. On the one hand, the addition of nanoparticles enhances the thermal conductivity. On the other hand, due to the interaction between the nanoparticles and base fluid causing the changes in the flow characteristics, which is also the main factor affecting the heat transfer of nanofluids. Therefore, a intensive study on the flow characteristics of nanofluids will make the study of heat transfer more meaningful. In this experiment, the flow characteristics of SiO2-water nanofluids in two-dimensional backward step flow are quantitatively studied by PIV. The results show that under the same Reynolds number, the turbulence of nanofluids is larger than that of pure water. With the increase of nanofluids volume fraction, the flow characteristics are constantly changing. The quantitative analysis proved that the nanofluids disturbance was enhanced compared with the base liquid, which resulting in the heat transfer enhancement.

Figure of Merit-Based Optimization Approach of Phase Change Material-based Composites for Portable Electronics Using Simplified Model

2021 ◽  
Author(s):  
Ayushman Singh ◽  
Srikanth Rangarajan ◽  
Leila Choobineh ◽  
Bahgat Sammakia
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Phase Change ◽  
Effective Thermal Conductivity ◽  
Phase Change Material ◽  
Figure Of Merit ◽  
Volume Fraction ◽  
Simplified Model ◽  
Transient Temperature ◽  
Change Material

Abstract This work presents an approach to optimally designing a composite with thermal conductivity enhancers (TCEs) infiltrated with phase change material (PCM) based on figure of merit (FOM) for thermal management of portable electronic devices. The FOM defines the balance between effective thermal conductivity and energy storage capacity. In present study, TCEs are in the form of a honeycomb structure. TCEs are often used in conjunction with PCM to enhance the conductivity of the composite medium. Under constrained composite volume, the higher volume fraction of TCEs improves the effective thermal conductivity of the composite, while it reduces the amount of latent heat storage simultaneously. The present work arrives at the optimal design of composite for electronic cooling by maximizing the FOM to resolve the stated trade-off. In this study, the total volume of the composite and the interfacial heat transfer area between the PCM and TCE are constrained for all design points. A benchmarked two-dimensional direct CFD model was employed to investigate the thermal performance of the PCM and TCE composite. Furthermore, assuming conduction-dominated heat transfer in the composite, a simplified effective numerical model that solves the single energy equation with the effective properties of the PCM and TCE has been developed. The effective thermal conductivity of the composite is obtained by minimizing the error between the transient temperature gradient of direct and simplified model by iteratively varying the effective thermal conductivity. The FOM is maximized to find the optimal volume fraction for the present design.

scholarly journals Numerical Analysis of Mixed Convective Heat Transfer from a Square Cylinder Utilizing Nanofluids with Multi-Phase Modelling Approach

Energies ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5485
Author(s):  
Rajendra S. Rajpoot ◽  
Shanmugam. Dhinakaran ◽  
Md. Mahbub Alam
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Convective Heat Transfer ◽  
Richardson Number ◽  
Base Fluid ◽  
Square Cylinder ◽  
Heat Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Multi Phase ◽  
Modelling Approach

The present study deals with the numerical simulation of mixed convective heat transfer from an unconfined heated square cylinder using nanofluids (Al2O3-water) for Reynolds number (Re) 10–150, Richardson number (Ri) 0–1, and nanoparticles volume fractions (φ) 0–5%. Two-phase modelling approach (i.e., Eulerian-mixture model) is adopted to analyze the flow and heat transfer characteristics of nanofluids. A square cylinder with a constant temperature higher than that of the ambient is exposed to a uniform flow. The governing equations are discretized and solved by using a finite volume method employing the SIMPLE algorithm for pressure–velocity coupling. The thermo-physical properties of nanofluids are calculated from the theoretical models using a single-phase approach. The flow and heat transfer characteristics of nanofluids are studied for considered parameters and compared with those of the base fluid. The temperature field and flow structure around the square cylinder are visualized and compared for single and multi-phase approaches. The thermal performance under thermal buoyancy conditions for both steady and unsteady flow regimes is presented. Minor variations in flow and thermal characteristics are observed between the two approaches for the range of nanoparticle volume fractions considered. Variation in φ affects CD when Reynolds number is varied from 10 to 50. Beyond Reynolds number 50, no significant change in CD is observed with change in φ. The local and mean Nusselt numbers increase with Reynolds number, Richardson number, and nanoparticle volume fraction. For instance, the mean Nusselt number of nanofluids at Re = 100, φ = 5%, and Ri = 1 is approximately 12.4% higher than that of the base fluid. Overall, the thermal enhancement ratio increases with φ and decreases with Re regardless of Ri variation.

CFD Investigation of Al2O3 Nanoparticles Effect on Heat Transfer Enhancement of Newtonian and Non-Newtonian Fluids in a Helical Coil

2019 ◽  
Vol 14 (3) ◽  
Author(s):  
Javad Aminian Dehkordi ◽  
Arezou Jafari
Keyword(s):  
Heat Transfer ◽  
Aqueous Solution ◽  
Nusselt Number ◽  
Base Fluid ◽  
Volume Fraction ◽  
Reynolds Numbers ◽  
Helical Coil ◽  
Al2o3 Nanoparticles ◽  
Nanoparticles Volume Fraction ◽  
Computational Fluid Dynamics Cfd

Abstract The present study applied computational fluid dynamics (CFD) to investigate the heat transfer of Newtonian (water) and non-Newtonian (0.3 %wt. aqueous solution of carboxymethylcellulose (CMC)) fluids in the presence of Al2O3 nanoparticles. To analyze the heat transfer rate, investigations were performed in a vertical helical coil as essential heat transfer equipment, at different inlet Reynolds numbers. To verify the accuracy of the simulation model, experimental data reported in the literature were employed. Comparisons showed the validity of simulation results. From the results, compared to the aqueous solution of CMC, water had a higher Nusselt number. In addition, it was observed that adding nanoparticles to a base fluid presented different results in which water/Al2O3 nanofluid with nanoparticles’ volume fraction of 5 % was more effective than the same base fluid with a volume fraction of 10 %. In lower ranges of Reynolds number, adding nanoparticles was more effective. For CMC solution (10 %), increasing concentration of nanoparticles caused an increase in the apparent viscosity. Consequently, the Nusselt number was reduced. The findings reveal the important role of fluid type and nanoparticle concentration in the design and development of heat transfer equipment.

Phase Change Material Particulate Flow Through a Rectangular Channel: Effect of Parachute-Shaped Particles on the Heat Transfer

2011 ◽  
Author(s):  
Laura Small ◽  
Fatemeh Hassanipour
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Phase Change ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Phase Change Material ◽  
Volume Fraction ◽  
Particulate Flow ◽  
Transfer Enhancement ◽  
Change Material

This study presents numerical simulations of forced convection with parachute-shaped encapsulated phase-change material particles in water, flowing through a square cross-section duct with top and bottom iso-flux surfaces. The system is inspired by the gas exchange process in the alveolar capillaries between the red blood cells (RBC) and the lung tissue. The numerical model was developed for the motion of elongated encapsulated phase change particles along a channel in a particulate flow where particle diameters are comparable with the channel height. Results of the heat transfer enhancement for the parachute-shaped particles are compared with the circular particles. Results reveal that the key role in heat transfer enhancement is the snugness movement of the particles and the parachute-shaped geometry yields small changes in heat transfer coefficient when compared to the circular ones. The effects of various parameters including particle diameter and volume-fraction, as well as fluid speed, on the heat transfer coefficient is investigated and reported in this paper.

scholarly journals Flow and Heat Transfer of Cu-Water Nanofluid between a Stretching Sheet and a Porous Surface in a Rotating System

2012 ◽  
Vol 2012 ◽  
pp. 1-18 ◽  
Author(s):  
M. Sheikholeslami ◽  
H. R. Ashorynejad ◽  
G. Domairry ◽  
I. Hashim
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Base Fluid ◽  
Stretching Sheet ◽  
Volume Fraction ◽  
Rotation Parameter ◽  
Nanoparticle Volume Fraction ◽  
Heat Transfer Characteristics ◽  
Rotating System ◽  
Flow And Heat Transfer

The aim of the present paper is to study the flow of nanofluid and heat transfer characteristics between two horizontal plates in a rotating system. The lower plate is a stretching sheet and the upper one is a solid porous plate. Copper (Cu) as nanoparticle and water as its base fluid have been considered. The governing partial differential equations with the corresponding boundary conditions are reduced to a set of ordinary differential equations with the appropriate boundary conditions using similarity transformation, which is then solved analytically using the homotopy analysis method (HAM). Comparison between HAM and numerical solutions results showed an excellent agreement. The results for the flow and heat transfer characteristics are obtained for various values of the nanoparticle volume fraction, suction/injection parameter, rotation parameter, and Reynolds number. It is shown that the inclusion of a nanoparticle into the base fluid of this problem is capable of causing change in the flow pattern. It is found that for both suction and injection, the heat transfer rate at the surface increases with increasing the nanoparticle volume fraction, Reynolds number, and injection/suction parameter and it decreases with power of rotation parameter.

scholarly journals Astray State-Laminar Forced Convective Heat Transfer of Al2O3 – H2O Nanofluid through 3D-Rectangular Cross- Sectional Duct

2019 ◽  
Vol 8 (2S3) ◽  
pp. 899-907
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Convective Heat Transfer ◽  
Friction Factor ◽  
Convective Heat ◽  
Flow Rate ◽  
Base Fluid ◽  
Volume Fraction ◽  
Phase Model ◽  
Forced Convective Heat Transfer

A Steady state-laminar forced convective heat transfer has been simulated by Computational Fluid Dynamics (CFD) with a Single Phase Model (SPM), Multi Phase model & Diameter effects and also determined the effects of nanoparticles concentration and nanofluid flow rate through 3D rectangular duct under certain boundary condition (constant heat flux). The nanofluid contains Alumina nanoparticles of size 60nm diameter used for MPM which is mixed with base fluid (water) with volume fraction of 0% ≤ ȼ ≤ 5% and Reynolds number (Re) ranges from 250 ≤ Re ≤ 1000. ANSYS 18.0 has been used for simulation. Three cases of analysis have been carried out in which the thermal conductivity (k) and dynamic viscosity (µ) of nanofluids are determined using two sets of theoretical models and one set of experimental k & µ data from literature respectively. The nanoparticles which stay more dispersed in the base fluid due to increase in Reynolds number which improves HTC and also decreases the friction factor accordingly. Particular attention has been paid to the variation of heat transfer characteristics when the modeling approach is switched from SPM to MPM. It is revealed that higher heat transfer rates are observed in MPM. The results shows that the friction factor decreases and Nusselt number (Nu) increases when there is an increase in the flow rate and also increase in the volume concentration of the nanofluid, while the pressure drop increases only slightly. The increase in HTC is one of the most important aims for industry and researchers.

Heat Transfer to Suspensions of Microencapsulated Phase Change Material Flowing Through Minichannels

2011 ◽  
Vol 134 (2) ◽  
Author(s):  
Frank Dammel ◽  
Peter Stephan
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Phase Change ◽  
Melting Temperature ◽  
Phase Change Material ◽  
Latent Heat ◽  
Particle Mass ◽  
Cooling Channels ◽  
Microencapsulated Phase Change Material ◽  
Change Material

The heat transfer to water-based suspensions of microencapsulated phase change material (MEPCM) flowing laminarly through rectangular copper minichannels was investigated both experimentally and numerically. The MEPCM-particles had an average size of 5 μm and contained as phase change material n-eicosane, which has a theoretical melting temperature of 36.4 °C. Water and suspensions with particle mass fractions of 10% and 20% were considered. While the experiments result in rather global values such as wall temperatures at certain points, suspension in- and outlet temperatures, and the pressure drop, the numerical simulations allow additionally a more detailed insight, for example, into the temperature distribution in the flowing suspension. The results show that MEPCM suspensions are only advantageous in comparison to water in a certain range of parameter combinations, where the latent heat is exploited to a high degree. The available latent heat storage potential, which depends on the particle fraction in the suspension and on the mass flow rate, has to be in the same order of magnitude as the supplied heat. Moreover, the mean residence time of the particles in the cooling channels must not be considerably shorter than the characteristic time for heat conduction perpendicular to the flow direction. Otherwise, the particles in the center region of the flow leave the cooling channels with still solid cores, and their latent heat is not exploited. Furthermore, the benefit of the added MEPCM particles depends on the inlet temperature, which has to be slightly below the theoretical melting temperature, and on the subcooling temperature after the heat supply, which has to be sufficiently low to guarantee that the entire phase change material solidifies again before it re-enters the cooling channels. The suspensions showed Newtonian behavior in the viscosity measurement. The actual pressure drop determined in the experiments is smaller than the pressure drop estimation based on the measured viscosities. The difference between the two values increases with increasing particle mass fraction. This shows that the particles are not evenly distributed in the flowing suspension, but that there is a particle-depleted layer close to the channel walls. This reduces the required pumping power, but makes it even more important to provide conditions, in which a sufficiently large amount of the supplied heat is conducted to the center region of the channels.

scholarly journals Impact of Surface Undulation on Flow and Heat Transfer Characteristics in an Enclosure Filled with Nanoencapsulated Phase Change Materials (NEPCMs)

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
A. Alhashash ◽  
H. Saleh
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Latent Heat ◽  
Phase Change Materials ◽  
Volume Fraction ◽  
The Core ◽  
Flow And Heat Transfer ◽  
Parametric Studies ◽  
Hybrid Nanofluids ◽  
Change Material

The present study investigates the natural convection in a wavy enclosure caused by a thermal difference between a cold wall and a hot undulated wall. The enclosure is filled with hybrid nanofluids. The hybrid nanofluids are formed of a phase change material (PCM) suspended in the water. The PCM utilizes polyurethane as the shell and nonadecane as the core. The core absorbs or releases its energy in the shape of latent heat inside the water and contributes to thermal energy storage and heat transfer. The governing equations are expressed in PDEs and solved by the finite element method (FEM). Parametric studies were used to analyze the solid concentration, fusion temperature, amplitude of corrugation, number of corrugations, and Rayleigh number. It is found that the heat transfer rate enhances by the rise of the latent heat of the NEPCM cores. The global heat transfer can be improved by more than 12 % by adding 1 % of NEPCM particles volume fraction. However, the heat transfer tends to decrease by applying the wavy surface.

Sign in / Sign up

Export Citation Format

Share Document