scholarly journals Effect of Blade Cambering on Dynamic Stall in View of Designing Vertical Axis Turbines

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Pablo Ouro ◽  
Thorsten Stoesser ◽  
Luis Ramírez
Keyword(s):  
Vertical Axis ◽  
Dynamic Stall ◽  
Hysteresis Cycle ◽  
Aerodynamic Coefficients ◽  
Pitching Motion ◽  
Large Eddy ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Good Agreement

This paper presents large eddy simulations (LESs) of symmetric and asymmetric (cambered) airfoils forced to undergo deep dynamic stall due to a prescribed pitching motion. Experimental data in terms of lift, drag, and moment coefficients are available for the symmetric NACA 0012 airfoil and these are used to validate the LESs. Good agreement between computed and experimentally observed coefficients is found confirming the accuracy of the method. The influence of foil asymmetry on the aerodynamic coefficients is analyzed by subjecting a NACA 4412 airfoil to the same flow and pitching motion conditions. Flow visualizations and analysis of aerodynamic forces allow an understanding and quantification of dynamic stall on both straight and cambered foils. The results confirm that cambered airfoils provide an increased lift-to-drag ratio and a decreased force hysteresis cycle in comparison to their symmetric counterparts. This may translate into increased performance and lower fatigue loads when using cambered airfoils in the design of vertical axis turbines (VATs) operating at low tip-speed ratios.

scholarly journals A Parametric Study of Trailing Edge Flap Implementation on Three Different Airfoils Through an Artificial Neuronal Network

Symmetry ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 828
Author(s):  
Igor Rodriguez-Eguia ◽  
Iñigo Errasti ◽  
Unai Fernandez-Gamiz ◽  
Jesús María Blanco ◽  
Ekaitz Zulueta ◽  
...  
Keyword(s):  
Aerodynamic Coefficients ◽  
Trailing Edge ◽  
High Lift ◽  
Trailing Edge Flaps ◽  
Artificial Neural Network Ann ◽  
Lift And Drag ◽  
Artificial Neuronal Network ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Trailing edge flaps (TEFs) are high-lift devices that generate changes in the lift and drag coefficients of an airfoil. A large number of 2D simulations are performed in this study, in order to measure these changes in aerodynamic coefficients and to analyze them for a given Reynolds number. Three different airfoils, namely NACA 0012, NACA 64(3)-618, and S810, are studied in relation to three combinations of the following parameters: angle of attack, flap angle (deflection), and flaplength. Results are in concordance with the aerodynamic results expected when studying a TEF on an airfoil, showing the effect exerted by the three parameters on both aerodynamic coefficients lift and drag. Depending on whether the airfoil flap is deployed on either the pressure zone or the suction zone, the lift-to-drag ratio, CL/CD, will increase or decrease, respectively. Besides, the use of a larger flap length will increase the higher values and decrease the lower values of the CL/CD ratio. In addition, an artificial neural network (ANN) based prediction model for aerodynamic forces was built through the results obtained from the research.

Wingtip Vortex Control Via Tip-Mounted Half-Delta Wings of Different Geometric Configurations

2015 ◽  
Vol 137 (12) ◽  
Author(s):  
T. Lee ◽  
S. Choi
Keyword(s):  
Tip Vortex ◽  
Delta Wings ◽  
Vortex Control ◽  
Vortex Pattern ◽  
Geometric Configurations ◽  
Wingtip Vortex ◽  
Wing Chord ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio

The control of the tip vortex, generated by a rectangular NACA 0012 wing, via tip-mounted half-delta wings (HDWs), of different slendernesses Λ, root chords cr, and deflections δ, was investigated experimentally at Re = 2.45 × 105. The results show that regardless of Λ, cr, and δ, the addition of HDWs consistently led to a diffused tip vortex. The degree of diffusion was, however, found to increase with decreasing Λ and cr. HDWs with cr ≤ 50% of the baseline-wing chord c caused a rapid diffusion of vorticity and rendered a weak circulation flowlike tip vortex, suggesting an enhanced wake-vortex decay and alleviation. The cr = 0.5c HDW also produced an improved lift-to-drag ratio. A unique double-vortex pattern also exhibited downstream of the cr ≤ 50%c HDW wings. The interaction and merging of the double vortex were expedited by upward HDW deflection.

Control of shock-induced vortex breakdown on a delta-wing-body configuration in the transonic regime

2021 ◽  
pp. 1-25
Author(s):  
Rajan B. Kurade ◽  
L. Venkatakrishnan ◽  
G. Jagadeesh
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Pressure Fluctuations ◽  
Angle Of Attack ◽  
Aerodynamic Coefficients ◽  
Delta Wings ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Sudden Jump ◽  
Modest Level

Abstract Shock-induced vortex breakdown, which occurs on the delta wings at transonic speed, causes a sudden and significant change in the aerodynamic coefficients at a moderate angle-of-attack. Wind-tunnel tests show a sudden jump in the aerodynamic coefficients such as lift force, pitching moment and centre of pressure which affect the longitudinal stability and controllability of the vehicle. A pneumatic jet operated at sonic condition blown spanwise and along the vortex core over a 60° swept delta-wing-body configuration is found to be effective in postponing this phenomenon by energising the vortical structure, pushing the vortex breakdown location downstream. The study reports that a modest level of spanwise blowing enhances the lift by about 6 to 9% and lift-to-drag ratio by about 4 to 9%, depending on the free-stream transonic Mach number, and extends the usable angle-of-attack range by 2°. The blowing is found to reduce the magnitude of unsteady pressure fluctuations by 8% to 20% in the aft portion of the wing, depending upon the method of blowing. Detailed investigations carried out on the location of blowing reveal that the blowing close to the apex of the wing maximises the benefits.

scholarly journals Proposal of an Optimized Airfoil Geometry for Vertical-Axis Wind Turbine Applications

Proceedings ◽  
2018 ◽  
Vol 2 (23) ◽  
pp. 1464
Author(s):  
Andrés Meana-Fernández ◽  
Lorena Díaz-Artos ◽  
Jesús Manuel Fernández Oro ◽  
Sandra Velarde-Suárez
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
High Lift ◽  
Actual Solution ◽  
Stall Angle ◽  
User Friendly ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
High Angles Of Attack

In this work, an airfoil geometry optimized for vertical-axis wind turbine applications is presented. Different airfoil shapes have been analyzed with JavaFoil, a panel method software. Then, the results from the analysis have been used to optimize the performance of the proposed airfoil shape (UO-17-LDA). This airfoil presents a high lift-to-drag ratio and a delayed stall angle with respect to the original FX-63-137 airfoil, making it suitable for vertical-axis wind turbine applications. The practicality of JavaFoil for the comparison of different airfoil geometries has been verified, as it is capable of obtaining results for a wide number of flow conditions in small computational times and with a user-friendly interface. Nevertheless, the results diverge from the actual solution for high angles of attack (beyond stall).

scholarly journals Design and experimental analysis of morphing wing based on biomimicry

2018 ◽  
Vol 7 (3.3) ◽  
pp. 239
Author(s):  
Mugeshwaran A ◽  
Guru Prasad Bacha ◽  
Rajkumar S
Keyword(s):  
Gear Ratio ◽  
Machining Process ◽  
Control Surface ◽  
Cad Model ◽  
Morphing Wing ◽  
Lift And Drag ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Aluminum Material

In this paper narrate about the study of aerodynamics in the multi-section morphing wing variation of baseline configuration to camber con-figuration. In particularly NACA 0012, section tried to morph as NACA 9312 camber section to achieve the lift to drag ratio in the flight condition based on the bio-mimicry. The CAD model and fabricated morphing wing in geometry scale of 20 cm chord and a 36 cm wing-span, with aluminum material ribs divided into 6 sections. Each section was able to rotate approximately 6 degrees without causing a discon-tinuity in the wing surface and also in order avoid the control surface based on the bio mimicry the morphing wing was designed and tested. DC-motor located at main spar with the two equal gear ratio the rib section used to morph the wing through the linear mechanical linkages. The aluminum ribs section are made through the EDM-Wire cut machining process for capable to actuate the morphing wing. In each sec-tion morphing wing can able provide up to 10 percent variation in the symmetrical airfoil to the cambered airfoil. The experimental test of the morphing was carried out in the cascade tunnel by force balancing method and the lift and drag output are compared.  

Effects of Aspect Ratio on the Hydrodynamic Performance of Circular Cambered Otter Board

2018 ◽  
Author(s):  
Liuyi Huang ◽  
Yuyan Li ◽  
Jiqiang Xu ◽  
Qingchang Xu ◽  
Fenfang Zhao ◽  
...  
Keyword(s):  
Lift Coefficient ◽  
Flow Distribution ◽  
Full Scale ◽  
Hydrodynamic Performance ◽  
High Lift ◽  
Aspect Ratios ◽  
Simulation Results ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Good Agreement

An otter board is an important device that provides a desired horizontal opening of a trawl net. A high lift coefficient or lift-to-drag ratio is required for an otter board to maintain fishing efficiency. In the present work, the hydrodynamic performance of a circular cambered otter board was studied by numerical simulation, including the effects of aspect ratios (AR), and flow distribution around the otter board. Model tests were conducted in the flume tank as well as a comparison to the numerical results. It showed that simulation results exhibited very good agreement with experiment results. Results demonstrated that the model otter board had a critical angle of attack (AOA) of 50° (when the stall appeared). The maximum lift coefficient and lift-to-drag ratio of the model otter board were 2.421 and 3.719, respectively. However, the maximum values of the full-scale otter board increased first and then decreased with an increasing AR. And the full-scale otter board had a better performance when AR = 2.489, it can enhance the lift coefficient by 17.4% compared with the initial otter board (AR = 1.25). In addition, the flow distribution around the otter board showed that the flow was smooth at small AOAs, when it attacked at large AOA (exceeded 55°), flow separation and eddies were appeared at the lee-side of the otter board.

scholarly journals Aerodynamic Analysis Models for Vertical-Axis Wind Turbines

1995 ◽  
Vol 2 (1) ◽  
pp. 15-21 ◽  
Author(s):  
M. T. Brahimi ◽  
A. Allet ◽  
I. Paraschivoiu
Keyword(s):  
Wind Turbines ◽  
Turbine Blades ◽  
Vertical Axis ◽  
Dynamic Stall ◽  
Wind Model ◽  
Current Effort ◽  
Vertical Axis Wind Turbines ◽  
Analysis Models ◽  
Good Agreement ◽  
Made In

This work details the progress made in the development of aerodynamic models for studying Vertical-Axis Wind Turbines (VAWT's) with particular emphasis on the prediction of aerodynamic loads and rotor performance as well as dynamic stall simulations. The paper describes current effort and some important findings using streamtube models, 3-D viscous model, stochastic wind model and numerical simulation of the flow around the turbine blades. Comparison of the analytical results with available experimental data have shown good agreement.

scholarly journals Effects of Pitching Motion Elements on Aerodynamic Characteristics of Airfoil

2021 ◽  
Vol 2076 (1) ◽  
pp. 012078
Author(s):  
Rui Yin ◽  
Jing Huang ◽  
Zhi-Yuan He
Keyword(s):  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Initial Angle ◽  
Pitching Motion ◽  
The Difference ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract The aerodynamic characteristics of NACA4412 airfoil with different pitching motion elements were compared and analyzed based on CFD in this research. The results are acquired as follows: the difference between the lift and drag coefficients of the airfoil during pitch up and pitch down motions becomes larger with the increase of the pitching amplitude or initial angle of attack; as the pitching amplitude increases, the lift coefficient grows slightly greater and the drag coefficient grows much greater; as the initial angle of attack increases, the lift coefficient grows much greater and the drag coefficient grows slightly; the smaller the attenuation frequency is, the larger the lift-to-drag ratio of the airfoil will be.

Large Eddy Simulation of the Flow Past Pitching NACA0012 Airfoil at 1E5 Reynolds Number

2014 ◽  
Author(s):  
Venkata Ravishankar Kasibhotla ◽  
Danesh Tafti
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Three Dimensional ◽  
Dynamic Stall ◽  
Eddy Simulation ◽  
Naca0012 Airfoil ◽  
Flow Past ◽  
Reduced Frequency ◽  
Large Eddy ◽  
Naca 0012

The paper is concerned with the prediction and analysis of dynamic stall of flow past pitching NACA-0012 airfoil at 105 Reynolds number based on the chord length of the airfoil and at reduced frequency of 0.188 in a three dimensional flow field. The turbulence in the flow field is resolved using large eddy simulations with dynamic Smagorinsky model at the sub grid scale. The lift hysteresis plots indicate closer match to experimental results, although discrepancies exist during the downstroke. The development of dynamic stall vortex, vortex shedding and reattachment as predicted by the present study are discussed in detail. This study has shown that the downstroke phase of the pitching motion is strongly three dimensional and is highly complex, whereas the flow is practically two dimensional during the upstroke.

scholarly journals Aerofoil optimization for improving the power performance of a vertical axis wind turbine using multiple streamtube model and genetic algorithm

2018 ◽  
Vol 5 (7) ◽  
pp. 180540 ◽  
Author(s):  
Changping Liang ◽  
Huaxing Li
Keyword(s):  
Wind Turbine ◽  
Tangential Force ◽  
Vertical Axis ◽  
Target Range ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Power Performance ◽  
Force Coefficient ◽  
Drag Ratio ◽  
Lift To Drag Ratio

This paper reports on the optimization of the NACA0015 aerofoil for improving the power performance of a vertical axis wind turbine (VAWT). The target range of the chord Re is 3 × 10 5 –10 6 , the tip speed ratio (TSR) is 2–6 and the solidity is 0.2–0.6. This aerofoil is widely applied in small-scale VAWTs. In the optimization process, in which the class and shape function transformation parametrization method was used to perturb the aerofoil geometry, the thickness and camber of the aerofoil were selected as the constraints and the value of the maximum tangential force coefficient was chosen as the objective function. The aerodynamic performance of the aerofoil was calculated by combining the XFOIL program and Viterna–Corrigan post-stall model, while the aerofoil's performance was validated with computational fluid dynamic simulations. The results illustrated that, compared to an unoptimized NACA0015 aerofoil, the optimized aerofoil's lift to drag ratio was improved over a wide range of attack angles and the stall performance was gentler. The maximum lift coefficient, the maximum lift to drag ratio and the maximum tangential force coefficient were increased by 7.5%, 9% and 8.87%, respectively. Finally, this paper predicted the rotor efficiency with both the unoptimized and optimized NACA0015 aerofoils for different TSRs and different solidities using the multiple streamtube model. The results showed that the rotor with the optimized aerofoil has a higher efficiency.

Sign in / Sign up

Export Citation Format

Share Document